Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2020.11–2021.08
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  OPERATION CHECK  


PRECAUTION FOR OPERATION CHECK


CAUTION:
C376913

Use the correct procedure to replace the airbag parts.



CHECK SRS WARNING LIGHT


a.

Primary check

i.
C129423

Turn the ignition switch to ON and check that the SRS warning light turns on.


ii.

Turn the ignition switch off. Wait for at least 2 seconds, and then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system (including the seat belt pretensioners) is performed.

NOTICE:

Turn the ignition switch off when the auxiliary battery is connected.


HINT:
·

If the warning light remains on for approximately 6 seconds or more after the ignition switch has been turned to ON, there may be a malfunction with the SRS airbag system.

·

If the warning light occasionally turns on approximately 6 seconds or more after the ignition switch has been turned to ON, there may be a short to +B, short to ground or an open in the SRS warning light circuit.

·

If the warning light illuminates after turning the ignition switch off or ACC, there may be a malfunction in the power source circuit or combination meter assembly.

·

The SRS warning light turns off, and then turns on. This blinking pattern indicates a source voltage drop. The SRS warning light turns off 10 seconds after the source voltage returns to normal.






FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR


a.

Initial check

i.

Turn the ignition switch to ON.


ii.

The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, and then goes off for approximately 2 seconds.

C401805


iii.

Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the following conditions.

Indicator Operation
Airbag Cutoff Switch Cylinder Sub-assembly Condition Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
ON ON OFF OFF
OFF OFF ON OFF
Switch failure OFF ON ON

HINT:

If the passenger airbag ON/OFF indicator does not operate as specified in the table according to the airbag cutoff switch cylinder sub-assembly status and the SRS warning light is not illuminated, no DTC will be output. Therefore, perform troubleshooting for trouble in the passenger airbag ON/OFF indicator.


C401812E04
3.5,1.906 3.5,0.729 3.5,0.729 3.656,0.729 false 4.146,1.896 4.146,1 4.146,1 4.302,1 false 4.615,1.906 4.615,1.313 4.615,1.313 4.771,1.313 false 0.135,2.542 1.802,3.375 1.667,0.833 10 false Passenger Airbag ON/OFF Indicator ("OFF Indicator"): 1.927,0.49 2.302,0.688 0.375,0.198 10 false ON 0.188,0.917 1.188,1.177 1,0.26 10 false Ignition Switch 1.969,1.219 2.948,1.76 0.979,0.542 10 false Off 1.969,2.927 2.948,3.469 0.979,0.542 10 false Off 1.875,2.188 2.854,2.729 0.979,0.542 10 false On 1.938,4.385 2.896,4.813 0.958,0.427 10 false Off 1.948,3.688 2.927,4.229 0.979,0.542 10 false On 0.104,0.052 4.396,0.573 4.292,0.521 12 false When passenger airbag is ready for activation: 3.771,0.656 5.792,1.115 2.021,0.458 10 false Approximately 4 seconds 4.396,0.927 6,1.74 1.604,0.813 10 false Approximately 2 seconds 4.875,1.24 5.833,2.219 0.958,0.979 10 false Approximately 60 seconds 0.063,3.979 1.729,4.813 1.667,0.833 10 false Passenger Airbag ON/OFF Indicator ("ON Indicator"):

C401813E04
3.375,1.896 3.375,0.719 3.375,0.719 3.531,0.719 false 4.073,1.906 4.073,1 4.073,1 4.229,1 false 0.094,2.563 1.75,3.24 1.656,0.677 10 false Passenger Airbag ON/OFF Indicator ("OFF Indicator"): 1.927,0.479 2.281,0.698 0.354,0.219 10 false ON 0.188,0.917 1.167,1.458 0.979,0.542 10 false Ignition Switch 1.948,1.208 2.927,1.75 0.979,0.542 10 false Off 1.979,2.917 2.958,3.458 0.979,0.542 10 false Off 2.021,2.188 3,2.729 0.979,0.542 10 false On 1.969,4.385 2.958,4.813 0.99,0.427 10 false Off 2,3.635 2.979,4.177 0.979,0.542 10 false On 0.083,0.042 4.146,0.521 4.063,0.479 12 false When passenger airbag is not ready for activation: 3.635,0.635 5.656,1.094 2.021,0.458 10 false Approximately 4 seconds 4.313,0.906 6.01,1.646 1.698,0.74 10 false Approximately 2 seconds 0.104,4.021 1.76,4.74 1.656,0.719 10 false Passenger Airbag ON/OFF Indicator ("ON Indicator"):




INSPECT AIRBAG COMPONENTS


Component to Inspect Procedure
Horn button assembly
1.

Perform a diagnostic system check.

2.

Visually check for defects with the horn button assembly removed from the vehicle.

HINT:

The defects are as follows:

·

The airbag has deployed

·

Cuts on the surface or in the grooves

·

Small cracks on the surface or in the grooves

·

Significant discoloration on the surface or in the grooves

·

Cracks or other damage to the connector

·

Deformation of the steering wheel assembly

·

Deformation of the installation surface of the horn button assembly

·

Interference or uneven clearance between the horn button assembly and steering wheel assembly when a new horn button assembly is installed to the steering wheel assembly



OK:

No defects are found.


If any defects are found, replace the horn button assembly or steering wheel assembly with a new one.


Lower No. 1 instrument panel airbag assembly
1.

Perform a diagnostic system check.

2.

Visually check for defects with the lower No. 1 instrument panel airbag assembly removed from the vehicle.

HINT:

The defects are as follows:

·

The airbag has deployed

·

Cuts

·

Small cracks

·

Significant discoloration

·

Cracks or other damage to the connector

·

Deformation or cracks on the No. 1 instrument panel brace sub-assembly, No. 3 instrument panel to cowl brace sub-assembly or instrument panel reinforcement assembly



OK:

No defects are found.


If any defects are found, replace the lower No. 1 instrument panel airbag assembly, No. 1 instrument panel brace sub-assembly, No. 3 instrument panel to cowl brace sub-assembly or instrument panel reinforcement assembly with a new one.


Instrument panel passenger without door airbag assembly
1.

Perform a diagnostic system check.

2.

Visually check for defects with the instrument panel passenger without door airbag assembly removed from the vehicle.

HINT:

The defects are as follows:

·

The airbag has deployed

·

Cuts

·

Small cracks

·

Significant discoloration

·

Cracks or other damage to the connector

·

Deformation or cracks on the instrument panel sub-assembly or instrument panel reinforcement assembly



OK:

No defects are found.


If any defects are found, replace the instrument panel passenger without door airbag assembly, instrument panel sub-assembly or instrument panel reinforcement assembly with a new one.


Curtain shield airbag assembly
1.

Perform a diagnostic system check.

2.

Visually check for defects with the curtain shield airbag assemblies removed from the vehicle.

HINT:

The defects are as follows:

·

The airbag has deployed

·

Cuts

·

Small cracks

·

Significant discoloration

·

Cracks or other damage to the connector



OK:

No defects are found.


If any defects are found, replace the curtain shield airbag assembly with a new one.


Front seat airbag assembly
1.

Perform a diagnostic system check.

2.

Visually check for defects with the front seat airbag assemblies installed to the vehicle.

HINT:

The defects are as follows:

·

The airbag has deployed

·

Scratches, broken or frayed threads on the surface of the front seatback assembly around the front seat airbag assemblies

·

Small cracks in the front seatback assembly around the front seat airbag assemblies

·

Significant discoloration on the front seatback assembly around the front seat airbag assemblies



OK:

No defects are found.


If any defects are found, replace the front seatback spring assembly, front seatback pad LH and front seatback cover with a new one.

3.

Visually check for defects with the front seat airbag assemblies removed from the vehicle.

HINT:

The defects are as follows:

·

The airbag has deployed

·

Scratches, broken or frayed threads on the surface of the base fabric of the front seat airbag assemblies

·

Marks from being dropped

·

Deformation of the installation surface of the front seat airbag assemblies

·

Cracks or other damage to the wire harness or connector



OK:

No defects are found.


If any defects are found, replace the front seat airbag assembly with a new one.


Front seat outer belt assembly
1.

Perform a diagnostic system check.

2.

Visually check for defects with the front seat outer belt assembly removed from the vehicle.

HINT:

The defects are as follows:

·

The seat belt pretensioner has deployed

·

Cuts

·

Small cracks

·

Significant discoloration

·

Cracks or other damage to the connector



OK:

No defects are found.


If any defects are found, replace the front seat outer belt assembly with a new one.


Pop up hood lifter assembly
1.

Perform a diagnostic system check.

2.

Visually check for defects with the pop up hood lifter assemblies removed from the vehicle.

HINT:

The defects are as follows:

·

The airbag has deployed

·

Cuts

·

Small cracks

·

Significant discoloration

·

Cracks or other damage to the connector



OK:

No defects are found.


If any defects are found, replace the pop up hood lifter assembly with a new one.


Airbag ECU assembly
1.

for Airbag that has not Deployed:

(a)

Perform a diagnostic system check.

(b)

Visually check for defects with the airbag ECU assembly installed to the vehicle.

HINT:

The defects are as follows:

·

Cracks on the ECU housing

·

Dents on the ECU housing

·

Chips on the ECU housing

·

Cracks or other damage to the connector

·

Peeling of the label



OK:

No defects are found.


If any defects are found, replace the airbag ECU assembly with a new one.


2.

for Airbag that has Deployed:

(a)

Replace the airbag ECU assembly.

HINT:

The airbag ECU assembly should be replaced after any of the SRS parts has deployed as it has been subjected to an impact.




Front airbag sensor
1.

When airbags have deployed as the result of a collision, be sure to replace all airbag sensors in the damaged areas (anywhere in need of repair).

2.

Visually check the airbag sensors in undamaged areas for defects.

HINT:

The defects are as follows:

·

Cracks on the sensor housing

·

Dents on the sensor housing

·

Chips on the sensor housing

·

Cracks or other damage to the connector

·

Damage to the serial number

·

Damage to the waterproof rubber seal



OK:

No defects are found.


If any defects are found or an airbag sensor has detected a major collision, replace the airbag sensor with a new one.

3.

Perform a diagnostic system check.


Side airbag sensor
Rear side airbag sensor
Pedestrian protection sensor
Side airbag pressure sensor assembly
Harness and connector
1.

Perform a diagnostic system check.

2.

Check any wire harnesses in exposed contact with the airbag wire harness for damage.

3.

Check the connector of the airbag wire harness for scratches, cracks or damage.