DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Current total driving distance | 0 to 16777215 [km/h] | Equivalent to the actual total driving distance | Cannot be used |
| Total Distance Traveled - Unit | - | - | - | Cannot be used |
| Main Switch | Trip switch (headup display switch) status | OFF or ON | OFF: Switch released
ON: Switch pushed |
- |
| +B Voltage | Auxiliary battery voltage | 0 to 25.5 [V] | 11 to 14 V | Ignition switch off |
| Illumination Rate from Illuminance Sensor | Light control sensor input value | 0 to 65535 [lx] | Value according to the brightness is output | 0 is displayed when there is no light |
| Vehicle Speed Meter | Vehicle speed input value | 0 to 255 [km/h] | Almost the same as actual vehicle speed | - |
| Brightness Up Switch | Brightness up switch | OFF or ON | OFF: Switch released
ON: Switch pushed |
This item can be inspected by adjusting a setting in the HUD settings of the settings tab displayed on the multi-information display. |
| Brightness Down Switch | Brightness down switch | OFF or ON | OFF: Switch released
ON: Switch pushed |
This item can be inspected by adjusting a setting in the HUD settings of the settings tab displayed on the multi-information display. |
| Projection Position Up Switch | Projection position up switch | OFF or ON | OFF: Switch released
ON: Switch pushed |
This item can be inspected by adjusting a setting in the HUD settings of the settings tab displayed on the multi-information display. |
| Projection Position Down Switch | Projection position down switch | OFF or ON | OFF: Switch released
ON: Switch pushed |
This item can be inspected by adjusting a setting in the HUD settings of the settings tab displayed on the multi-information display. |
| Display Change Switch | - | - | - | Cannot be used |
| Display Angle | Display angle of headup display | -12.7 to 12.8 [deg] | Current display angle of headup display | ·
Approximately -12.7 deg: vehicle rear ·
Approximately - 0 deg: center ·
Approximately 12.7 deg: vehicle front |
| Ambient Temperature (Celsius) | Ambient temperature (celsius) | -40 to 87 [°C] | Actual ambient temperature displayed | - |
| Ambient Temperature (Fahrenheit) | Ambient temperature (fahrenheit) | -40 to 215 [°F] | Actual ambient temperature displayed | - |
| Illumination Rate from Light Control Sensor | - | 0 to 65535 [lx] | - | - |
| LDA System | Availability of lane tracing assist system | With or Without | With: Vehicle equipped with lane tracing assist system
Without: Vehicle not equipped with lane tracing assist system |
- |
| PCS System | Availability of pre-collision system | With or Without | With: Vehicle equipped with pre-collision system
Without: Vehicle not equipped with pre-collision system |
- |
| ICS System | Availability of parking support brake system | With or Without | With: Vehicle equipped with parking support brake system
Without: Vehicle not equipped with parking support brake system |
- |
| Radar Cruise System | Availability of dynamic radar cruise control system | With or Without | With: w/ Dynamic radar cruise control system
Without: w/o Dynamic radar cruise control system |
- |
| Road Sign Assist System | Availability of road sign assist system | With or Without | With: Vehicle equipped with road sign assist system
Without: Vehicle not equipped with road sign assist system |
- |
| ITS System | Availability of ITS System | With or Without | With: Vehicle equipped with ITS system
Without: Vehicle not equipped with ITS system |
- |
| HV System Indicator | Hybrid system indicator value | -101 to 511 [%] | Current hybrid system indicator status displayed | - |
| Navigation System | Availability of navigation system | With or Without | With: Vehicle equipped with navigation system
Without: Vehicle not equipped with navigation system |
- |
| Master Caution Display Function | Headup display master caution display setting | OFF or ON | Current headup display master caution display setting displayed | - |
| Memory Call Link Function | Headup display memory call link setting | OFF or ON | Current headup display memory call link setting displayed | Cannot be used |
| Seat Switch Link Function | Headup display power seat switch link setting | OFF or ON | Current headup display power seat switch link setting displayed | Cannot be used |
| Pedestrian Reminder System | Availability of pedestrian reminder system | With or Without | With: Vehicle equipped with pedestrian reminder system
Without: Vehicle not equipped with pedestrian reminder system |
- |
| FCTA System | Availability of FCTA system | With or Without | With: Vehicle equipped with FCTA system
Without: Vehicle not equipped with FCTA system |
- |
| LTC System | Availability of LTC system | With or Without | With: Vehicle equipped with FCTA system
Without: Vehicle not equipped with FCTA system |
- |
| LCS System | Availability of LCS system | With or Without | Without: Vehicle not equipped with LCS system
Without: Vehicle not equipped with LCS system |
- |
| LVN System | Availability of LVN system | With or Without | Without: Vehicle not equipped with LVN system
Without: Vehicle not equipped with LVN system |
- |
| Driver Emergency Stop Assist System | - | - | - | Cannot be used |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Color Test Screen (Black) | Displays each color on headup display | ON | - |
| Color Test Screen (White) | Displays each color on headup display | ON | - |
| Color Test Screen (Red) | Displays each color on headup display | ON | - |
| Color Test Screen (Green) | Displays each color on headup display | ON | - |
| Color Test Screen (Blue) | Displays each color on headup display | ON | - |
| Color Test Screen (Color Bars) | Displays each color on headup display | ON | - |
| Color Test Screen (Adjustment) | Displays each color on headup display | ON | - |
| Display Brightness | Changes the brightness of headup display | 0 to 100 [%] | - |
| Display Position | Move the position of headup display | Up (+3)/Up (+2)/Up (+1)/Center/Down (-1)/Down (-2)/Down (-3) | - |