Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455114 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  U0125  Lost Communication with Yaw Rate Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  U0129  Lost Communication with Brake System Control Module  U0142  Lost Communication with Body Control Module "B"  U0293  Lost Communication with Hybrid/EV Vehicle Control System  


DESCRIPTION

These DTCs are stored if there is a malfunction in the CAN communication system connected to the blind spot monitor sensor.

HINT:

If CAN communication system DTCs are stored, they may also be stored for other systems.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U0125 Lost Communication with Yaw Rate Sensor Module Lost communication with airbag ECU assembly CAN communication system Blind Spot Monitor Master B
U0126 Lost Communication with Steering Angle Sensor Module Lost communication with steering sensor CAN communication system Blind Spot Monitor Master B
U0129 Lost Communication with Brake System Control Module Lost communication with No. 2 skid control ECU assembly CAN communication system Blind Spot Monitor Master B
U0142 Lost Communication with Body Control Module "B" Lost communication with main body ECU (multiplex network body ECU) CAN communication system Blind Spot Monitor Master B
U0293 Lost Communication with Hybrid/EV Vehicle Control System Lost communication with EV control ECU CAN communication system Blind Spot Monitor Master B

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U0125 Lost Communication with Yaw Rate Sensor Module Lost communication with airbag ECU assembly CAN communication system Blind Spot Monitor Slave B
U0126 Lost Communication with Steering Angle Sensor Module Lost communication with steering sensor CAN communication system Blind Spot Monitor Slave B
U0129 Lost Communication with Brake System Control Module Lost communication with No. 2 skid control ECU assembly CAN communication system Blind Spot Monitor Slave B
U0142 Lost Communication with Body Control Module "B" Lost communication with main body ECU (multiplex network body ECU) CAN communication system Blind Spot Monitor Slave B
U0293 Lost Communication with Hybrid/EV Vehicle Control System Lost communication with EV control ECU CAN communication system Blind Spot Monitor Slave B

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313

HINT:
·

If CAN communication system DTCs are stored, they may also be stored for other systems.

·

If the CAN communication system has been inspected and repaired, the DTCs will not be output when rechecking for DTCs.

·

If these DTCs are output frequently, duplicate the conditions that cause the problem symptoms and perform the inspection again, even if the DTCs were not output when rechecking for DTCs.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK FOR DTC

B

2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

HINT:
·

If CAN communication system DTCs are stored, they may also be stored for other systems.

·

If the CAN communication system has been inspected and repaired, the DTCs will not be output when rechecking for DTCs.

·

If these DTCs are output frequently, duplicate the conditions that cause the problem symptoms and perform the inspection again, even if the DTCs were not output when rechecking for DTCs.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B