PARKING ASSIST ECU
Disconnect the G13 parking assist ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| G13-1 (+B) - G13-4 (GND1) | Power source signal | Ignition switch off | 11 to 14 V |
| G13-2 (ACC) - G13-4 (GND1) | ACC power source signal | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| G13-3 (IG) - G13-4 (GND1) | IG power source signal | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| G13-4 (GND1) - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G13 parking assist ECU connector.
Measure the voltage, resistance and waveform according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| G13-11 (CANH) | CAN communication line | - | - |
| G13-12 (CANL) | CAN communication line | - | - |
| G13-13 (RSW+) - G13-4 (GND1) | Terminal required by law | Panoramic image being displayed | 0 to 2 V |
| Panoramic image not being displayed | 5.5 to 7.05 V | ||
| G13-15 (BLSW) - G13-4 (GND1) | Panoramic view monitor switch signal | Ignition switch ON, panoramic view monitor switch off | 5.5 to 6.5 V |
| Ignition switch ON, panoramic view monitor switch on | Below 1 V | ||
| G138-1 (GVO+) | Video signal (Digital) | - | - |
| G138-2 (GVO-) | Video signal (Digital) | - | - |
| G138-3 (GVG1) | Shield ground | - | - |
| G140-1 (BGND) - Body ground | Front television camera assembly display ground | Always | Below 1 Ω |
| G140-2 (BCB+) - G140-1 (BGND) | Power source to front television camera | Ignition switch ON | 7 to 8 V |
| G140-3 (BCV-) | Front television camera assembly display ground | - | - |
| G140-4 (BCV+) | Front television camera assembly display signal input | - | - |
| G140-5 (SGND) - Body ground | Front television camera assembly ground (shield) | Always | Below 1 Ω |
| G141-1 (LGND) - Body ground | Side television camera assembly LH ground | Always | Below 1 Ω |
| G141-2 (LCB+) - G141-1 (LGND) | Power source to side television camera assembly LH | Ignition switch ON | 7 to 8 V |
| G141-3 (LCV-) | Side television camera assembly LH display ground | - | - |
| G141-4 (LCV+) | Side television camera assembly LH display signal input | - | - |
| G141-5 (SGND) - Body ground | Side television camera assembly LH ground (shield) | Always | Below 1 Ω |
| G142-1 (CGND) - Body ground | Rear television camera assembly ground | Always | Below 1 Ω |
| G142-2 (CB+) - G142-1 (CGND) | Power source to rear television camera assembly | Ignition switch ON | 7 to 8 V |
| G142-3 (CV-) | Rear television camera assembly display ground | - | - |
| G142-4 (CV+) | Rear television camera assembly display signal input | - | - |
| G142-5 (SGND) - Body ground | Rear television camera assembly ground (shield) | Always | Below 1 Ω |
| G139-1 (RGND) - Body ground | Side television camera assembly RH display ground | Always | Below 1 Ω |
| G139-2 (RCB+) - G139-1 (RGND) | Power source to side television camera assembly RH | Ignition switch ON | 7 to 8 V |
| G139-3 (RCV-) | Side television camera assembly RH display ground | - | - |
| G139-4 (RCV+) | Side television camera assembly RH display signal input | - | - |
| G139-5 (SGND) - Body ground | Side television camera assembly RH ground (shield) | Always | Below 1 Ω |
MULTI-DISPLAY ASSEMBLY
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>TERMINALS OF ECU