Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455450 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2789  No Response from ID BOX  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2789 No Response from ID BOX No communication between the certification ECU and ID code box for 10 seconds or more.
·

ID code box (immobiliser code ECU)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Entry&Start B

WIRING DIAGRAM

B445874E70
4.344,0.396 5.906,0.813 1.563,0.417 10 false from Auxiliary Battery 5.156,0.948 5.563,1.24 0.406,0.292 10 false 1 5.604,0.917 6.5,1.313 0.896,0.396 10 false SMART 4.875,1.073 5.281,1.365 0.406,0.292 10 false +B 4.771,2 5.177,2.292 0.406,0.292 10 false GND 5.167,1.885 5.573,2.177 0.406,0.292 10 false 5 4.229,1.469 4.635,1.76 0.406,0.292 10 false LIN1 4.042,1.323 4.448,1.615 0.406,0.292 10 false 2 2.146,1.323 2.552,1.615 0.406,0.292 10 false 13 0.906,2.313 1.313,2.604 0.406,0.292 10 false D86 0.865,2.521 2.396,3.063 1.531,0.542 10 false Certification ECU (Smart Key ECU Assembly) 0.667,3.479 2.698,3.708 2.031,0.229 10 false : LIN Communication Line 3.938,2.323 4.344,2.615 0.406,0.292 10 false D73 3.927,2.542 5.5,3.083 1.573,0.542 10 false ID Code Box (Immobiliser Code ECU) 1.844,1.469 2.25,1.76 0.406,0.292 10 false LIN

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or immobiliser code ECU, refer to the smart access system with push-button start (for start function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION



HINT:

When the communication between the ID code box (immobiliser code ECU) and certification ECU (smart key ECU assembly) stops, DTC B2785 is also stored.


PROCEDURE

1.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

Procedure1

a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Result:
Result Proceed to
B2789 is output A
B2789 is not output B



Post-procedure1

a.

None



A

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) POWER SOURCE CIRCUIT)

B

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Disconnect the D73 ID code box (immobiliser code ECU) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D73)Location & Routing

Click Connector(D73)Instrument Panel>Instrument Panel Wire>ID Code Box (Immobiliser Code ECU)

D73-5 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D73)Location & Routing

Click Connector(D73)Instrument Panel>Instrument Panel Wire>ID Code Box (Immobiliser Code ECU)

D73-1 (+B) - Body ground Ignition switch off 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ID CODE BOX (IMMOBILISER CODE ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ID CODE BOX (IMMOBILISER CODE ECU))

Pre-procedure1

a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D73 ID code box (immobiliser code ECU) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86,D73)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

Click Connector(D73)Instrument Panel>Instrument Panel Wire>ID Code Box (Immobiliser Code ECU)

D86-13 (LIN) - D73-2 (LIN1) Always Below 1 Ω
D86-13 (LIN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR