Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2020.11–2021.08
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM D

NETWORKING  CAN COMMUNICATION SYSTEM  DIAGNOSIS SYSTEM  


Description of "Communication Bus Check" Screen


NOTICE:

The following communication bus check screen is provided only as an example. This screen differs from the actual screen for this vehicle.


HINT:

The ECUs and sensors that are normally connected to the CAN communication system are displayed on the GTS.


a.

Select "Communication Bus Check" on the menu screen of the GTS.

HINT:

If items are not selected correctly in the vehicle specification pop up screen, the name of the CAN junction connector to which the ECUs or sensors are connected may not be displayed on the "Communication Bus Check" screen.



b.

Confirm that the "Communication Bus Check" screen is displayed and the ECUs and sensors that have a history of being connected to the monitoring ECU are displayed.

HINT:
·

Even if an ECU or sensor that is connected to a bus that is monitored by a bus monitoring ECU (gateway function equipped ECU) is not communicating, it will remain displayed on the "Communication Bus Check" screen.

·

When an ECU or sensor that is connected to a bus that is not monitored by a bus monitoring ECU (gateway function equipped ECU) is not displayed on the "Communication Bus Check" screen, it means that it is not communicating.

·

ECUs with a history of being connected are displayed even if the ECUs are removed.




c.

The default display setting selected on the combo box is ALL. When checking for ECUs or sensors for a specific bus, choose the bus from the drop down list. ALL, each bus, each sub bus and Central Gateway are listed in the drop down list.

C352726C01
3.146,4.833 3.635,4.646 true 0.135,2.75 0.448,2.948 0.313,0.198 10 false *b 3.719,4.531 4.031,4.729 0.313,0.198 10 false *a
*a Combo box *b Background color is red or yellow


Item Detail
Combo box: ALL Displays all ECUs and sensors connected to the central bus and sub buses.
Combo box: Bus Displays ECUs and sensors connected to the selected bus.
Combo box: Sub bus Displays ECUs and sensors connected to the selected sub bus.
Combo box: Central Gateway Displays all ECUs and sensors connected to the central bus.

NOTICE:
·

When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).

·

In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose the CAN communication system, refer to System Diagram.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM



HINT:

The background color of an ECU or sensor changes according to its connection status as indicated in the following table.

Description of "Communication Bus Check" Screen
Bus Type Background Color Connection Status
Bus White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check.

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4

·

No ECUs or sensors are connected to the bus.*5


Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check.

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU.*6

·

No ECUs or sensors are connected to the sub bus.*7



·

Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.

·

*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.

·

*2: The gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.

·

*3: The gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.

·

*4: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the names of buses, sub buses, ECUs and sensors will not be displayed.

·

*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.

·

If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU (network gateway ECU) and diagnosis bus (The bus that connects the DLC3 to the central gateway ECU (network gateway ECU)) for malfunctions.




d.

Monitor the screen for any ECU or sensor connection status changes for a period of 2 minutes.

HINT:
·

If an open occurs in one of the wires of a CAN branch line, it may interfere with the communication of other ECUs or sensors resulting in an incorrect state being displayed.

·

If the connection status changes intermittently during the inspection, repair the open in the branch line of the ECU or sensor that is not communicating, and then perform the Communication Bus Check again.





Description of "Communication Bus Check (Detail)" Screen


NOTICE:

The following communication bus check screen is provided only as an example. This screen differs from the actual screen for this vehicle.


HINT:

The communication error history of ECUs or sensors which have communication error history can be displayed on the "Communication Bus Check (Detail)" screen.


a.

Select "Communication Bus Check" on the menu screen of the GTS.

HINT:

If items are not selected correctly in the vehicle specification pop up screen, the name of the CAN junction connector to which the ECUs or sensors are connected may not be displayed on the "Communication Bus Check" screen.



b.

Select "Detail" on the "Communication Bus Check" screen.

C352727C01
4.521,4.906 4.167,4.583 4.167,4.583 4,4.583 true 3.802,4.49 4.115,4.688 0.313,0.198 10 false *a
*a Communication Bus Check (Detail) - -



c.

Confirm that the "Communication Bus Check (Detail)" screen is displayed and the communication error history of the ECUs or sensors up to present is displayed.

HINT:
·

Lost Communication Time and Lost Communication Trip are only displayed for the central bus.

·

Lost Communication Time and Lost Communication Trip are not displayed for sub buses.




d.

The default display setting selected on the combo box is ALL. When checking for ECUs or sensors for a specific bus, choose the bus from the drop down list. ALL, each bus, each sub bus and Central Gateway are listed in the drop down list.

C352728C01
3.156,4.833 3.719,4.667 true 0.219,1.906 0.531,2.104 0.313,0.198 10 false *b 3.781,4.552 4.094,4.75 0.313,0.198 10 false *a
*a Combo box *b Background color is red


Item Detail
Combo box: ALL Displays all ECUs and sensors connected to the central bus and sub buses.
Combo box: Bus Displays ECUs and sensors connected to the selected bus.
Combo box: Sub bus Displays ECUs and sensors connected to the selected sub bus.
Combo box: Central Gateway Displays all ECUs and sensors connected to the central bus.
Bus Monitoring ECU Displays the gateway function equipped ECU which monitors the selected bus or sub bus.
Current Trip Displays the total number of trips up to now*
Lost Communication Time(s) Displays the longest period of time in seconds that the ECU or sensor connected to the central bus was not communicating.
Lost Communication Trip Displays the trip in which the longest period of time that the ECU or sensor connected to the central bus was not communicating occurred.

*: If the component has been replaced with a new one, the total number of trips after the replacement is displayed.


NOTICE:
·

The Lost Communication Time column displays the longest period of time in seconds that the central gateway ECU (network gateway ECU) detected a communication stop in the respective ECU or sensor.

·

The Lost Communication Trip column displays the trip in which the central gateway ECU (network gateway ECU) detected the longest communication stop in the respective ECU or sensor.

·

When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).

·

In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose the CAN communication system, refer to the System Diagram.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM



HINT:

The background color of an ECU or sensor changes according to its connection status as indicated in the following table.

Description of "Communication Bus Check (Detail)" Screen
Bus Type Background Color Connection Status
Bus White Either of the following:
·

Communication has been normal.

·

Lost Communication Time is below 6 seconds.


Red Lost Communication Time is 6 seconds or more.
Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*1

·

No ECUs or sensors are connected to the bus.*2


Sub bus White Lost Communication Time is displayed as "-".
Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU.*3

·

No ECUs or sensors are connected to the sub bus.*4



·

If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU (network gateway ECU) and diagnosis bus (The bus that connects the DLC3 to the central gateway ECU (network gateway ECU)) for malfunctions.

·

Lost Communication Time and Lost Communication Trip are not displayed for sub buses.

·

*1: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the names of buses, sub buses, ECUs and sensors will not be displayed.

·

*2: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*3: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the names of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*4: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.





Communication Bus Check (Communication Malfunction Check)


HINT:

DTCs related to CAN communication are displayed for each ECU on the GTS.


a.

Select "Communication Bus Check" on the menu screen of the GTS.


b.

Select "Communication Malfunction Check" on the "Communication Bus Check" screen.

C352729C01
5.073,4.896 4.917,4.583 4.917,4.583 4.083,4.583 true 3.896,4.49 4.208,4.688 0.313,0.198 10 false *a
*a Communication Malfunction Check - -



c.

Confirm that the "Communication Malfunction Check" screen is displayed and CAN communication DTCs for each ECU are displayed.

HINT:

When there are no CAN communication DTCs stored, no DTCs will be displayed.




How to Use "Communication Bus Check" Screen in Inspection


NOTICE:

The following CAN bus wiring diagram or communication bus check screen is provided only as an example. This wiring diagram or screen differs from the actual one for this vehicle.


HINT:
·

If the CAN communication system is currently malfunctioning, it is recommended to use Communication Bus Check rather than Communication DTCs for determining the suspected area.

·

Turn the ignition switch to ON, or perform the necessary operations to reproduce the problem symptom, select "Communication Bus Check" and wait approximately 2 minutes. Check the communication status of each ECU or sensor on the screen while performing this operation.



a.

If the CAN communication system is currently malfunctioning, determine the suspected area using the Communication Bus Check as follows:

Problem Symptoms Table
Problem Symptom Pattern Display on Communication Bus Check Screen Suspected Area
A Almost all of the ECUs and sensors connected to the malfunctioning CAN bus are displayed as not communicating on the "Communication Bus Check" screen.
·

Short between CAN bus lines (CANH and CANL)

·

Short to +B in a CAN bus line (CANH or CANL)

·

Short to ground in a CAN bus line (CANH or CANL)


B ECUs or sensors farther from the central gateway ECU (network gateway ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen. Open in both wires of a main bus line in the central bus
C One ECU or sensor is displayed as not communicating on the "Communication Bus Check" screen.
·

Open in both wires of a branch line connected to an ECU or sensor in the central bus

·

Internal malfunction of an ECU or sensor in the central bus

·

Malfunction in the power supplied to an ECU or sensor in the central bus


D
·

No ECUs or sensors are displayed on the "Communication Bus Check" screen.

·

All ECUs or sensors are displayed as not communicating on the "Communication Bus Check" screen.


·

Internal malfunction of the central gateway ECU (network gateway ECU)

·

Malfunction in the power supplied to the central gateway ECU (network gateway ECU)

·

Open in both wires of the branch line in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU))

·

Short between CAN bus lines (CANH and CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU))

·

Short to +B in a CAN bus line (CANH or CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU))

·

Short to ground in a CAN bus line (CANH or CANL) in the diagnosis bus (DLC3 - Central gateway ECU (network gateway ECU))


E One ECU or sensor is displayed as not communicating in multiple buses on the "Communication Bus Check" screen.
·

Internal malfunction of an ECU or sensor connected to multiple buses

·

Malfunction in the power supplied to an ECU or sensor connected to multiple buses


F Some ECUs or sensors are displayed as not communicating in the central bus and other ECUs or sensors are displayed as not communicating in a sub bus.
·

Open in a wire of a branch line connected to an ECU or sensor in the central bus

·

Internal malfunction of an ECU or sensor in the central bus


G A gateway function equipped ECU is displayed as not communicating in the central bus and ECUs and sensors connected to its respective sub bus are not displayed.
·

Open in both wires of a branch line connected to a gateway function equipped ECU

·

Internal malfunction of a gateway function equipped ECU

·

Malfunction in the power supplied to a gateway function equipped ECU


H One ECU or sensor is displayed as not communicating in a sub bus on the "Communication Bus Check" screen.
·

Open in both wires of a branch line connected to an ECU or sensor in a sub bus

·

Internal malfunction of an ECU or sensor in a sub bus

·

Malfunction in the power supplied to an ECU or sensor in a sub bus


I ECUs or sensors farther from the sub bus monitoring ECU (gateway function equipped ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen. Open in both wires of a main bus line in a sub bus


b.

Problem Symptom Pattern A

Display on Communication Bus Check Screen Almost all of the ECUs and sensors connected to the malfunctioning CAN bus are displayed as not communicating on the "Communication Bus Check" screen.
Details of Malfunction
·

Short between CAN bus lines (CANH and CANL) in Bus 2

·

Short to +B in a CAN bus line (CANH or CANL) in Bus 2

·

Short to ground in a CAN bus line (CANH or CANL) in Bus 2



C416688C01
2.073,3.344 2.677,3.542 0.604,0.198 10 false F-MGC 3.74,3.333 4.198,3.531 0.458,0.198 10 false HVB 1.938,3.917 2.969,4.146 1.031,0.229 10 false CAN J/C 1 4.313,3.333 5.021,3.594 0.708,0.26 10 false R-MGC 2.458,4.5 2.917,4.698 0.458,0.198 10 false BRK 1.844,5.74 2.302,5.938 0.458,0.198 10 false MB 3.052,7.135 3.573,7.344 0.521,0.208 10 false MIR-R 4.969,7.135 5.5,7.365 0.531,0.229 10 false MIR-L 6.406,3.917 6.865,4.115 0.458,0.198 10 false ENG 5.729,5.073 6.188,5.271 0.458,0.198 10 false SRS 1.854,4.5 2.313,4.698 0.458,0.198 10 false HV 6.479,6.521 6.771,6.865 0.292,0.344 10 false ST 1.521,7.188 1.979,7.385 0.458,0.198 10 false DLC3 3.729,5.698 4.188,5.896 0.458,0.198 10 false EPS 4.396,5.698 4.854,5.896 0.458,0.198 10 false STR 5.781,3.26 6.24,3.458 0.458,0.198 10 false : *e 0.448,5.344 0.906,5.542 0.458,0.198 10 false CGW 3.875,3.917 4.906,4.146 1.031,0.229 10 false CAN J/C 2 1.938,5.094 2.969,5.323 1.031,0.229 10 false CAN J/C 3 3.875,5.094 4.906,5.323 1.031,0.229 10 false CAN J/C 4 2.896,6.531 3.927,6.76 1.031,0.229 10 false CAN J/C 5 4.823,6.521 5.854,6.75 1.031,0.229 10 false CAN J/C 6 1,3.74 1.458,3.938 0.458,0.198 10 false *a 1.01,4.917 1.469,5.115 0.458,0.198 10 false *b 1.01,7.073 1.469,7.271 0.458,0.198 10 false *d 1.677,6.167 2.135,6.365 0.458,0.198 10 false *c 0.479,0.74 0.938,0.938 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction
·

Short between CAN bus lines (CANH and CANL) in bus lines

·

Short to +B in a CAN bus line (CANH or CANL) in bus lines

·

Short to ground in a CAN bus line (CANH or CANL) in bus lines


*f Background color is red


HINT:
·

Due to the malfunction, almost all of the ECUs and sensors connected to Bus 2 will be displayed as not communicating and their background color will be red.

·

The malfunction in Bus 2 will not affect the other buses.

·

The malfunctioning part can be determined by inspecting for an open in the main bus line, a short between bus lines or a short to +B or ground.

·

Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.



Display on Communication Bus Check Screen Almost all of the ECUs and sensors connected to the malfunctioning CAN bus are displayed as not communicating on the "Communication Bus Check" screen.
Details of Malfunction
·

Short between CAN bus lines (CANH and CANL) in Bus 4

·

Short to +B in a CAN bus line (CANH or CANL) in Bus 4

·

Short to ground in a CAN bus line (CANH or CANL) in Bus 4



C416689C01
2.063,3.333 2.594,3.573 0.531,0.24 10 false F-MGC 3.74,3.333 4.198,3.531 0.458,0.198 10 false HVB 4.302,3.333 4.906,3.615 0.604,0.281 10 false R-MGC 6.406,3.917 6.865,4.115 0.458,0.198 10 false ENG 1.865,4.49 2.323,4.688 0.458,0.198 10 false HV 2.458,4.49 2.917,4.688 0.458,0.198 10 false BRK 5.74,5.083 6.198,5.281 0.458,0.198 10 false SRS 4.406,5.688 4.865,5.885 0.458,0.198 10 false STR 3.75,5.698 4.208,5.896 0.458,0.198 10 false EPS 1.844,5.75 2.302,5.948 0.458,0.198 10 false MB 6.469,6.531 6.927,6.729 0.458,0.198 10 false ST 4.969,7.135 5.458,7.333 0.49,0.198 10 false MIR-L 3.063,7.135 3.583,7.406 0.521,0.271 10 false MIR-R 1.51,7.188 1.969,7.385 0.458,0.198 10 false DLC3 1.948,3.917 2.698,4.177 0.75,0.26 10 false CAN J/C 1 3.875,3.917 4.625,4.177 0.75,0.26 10 false CAN J/C 2 1.958,5.083 2.708,5.344 0.75,0.26 10 false CAN J/C 3 3.885,5.073 4.635,5.333 0.75,0.26 10 false CAN J/C 4 2.938,6.521 3.688,6.781 0.75,0.26 10 false CAN J/C 5 4.854,6.521 5.604,6.781 0.75,0.26 10 false CAN J/C 6 5.646,3.26 6.104,3.458 0.458,0.198 10 false : *e 1,3.729 1.458,3.927 0.458,0.198 10 false *a 1.01,7.073 1.469,7.271 0.458,0.198 10 false *d 1.698,6.156 2.156,6.354 0.458,0.198 10 false *c 1,4.917 1.458,5.115 0.458,0.198 10 false *b 0.51,1.698 0.969,1.896 0.458,0.198 10 false *f 0.49,2.417 0.948,2.615 0.458,0.198 10 false *g 0.458,5.427 0.917,5.625 0.458,0.198 10 false CGW
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction
·

Short between CAN bus lines (CANH and CANL) in bus lines

·

Short to +B in a CAN bus line (CANH or CANL) in bus lines

·

Short to ground in a CAN bus line (CANH or CANL) in bus lines


*f Background color is red
*g Not displayed - -


HINT:
·

Due to the malfunction, almost all of the ECUs and sensors connected to Bus 4 will be displayed as not communicating and their background color will be red.

·

The malfunction will not affect the other buses of the central bus. However, the sub bus connected to Bus 4 is likely to be affected. the gateway function equipped ECU connected to Bus 4 will not communicate and consequently the sub bus and its respective ECUs or sensors monitored by the gateway function equipped ECU (sub bus monitoring ECU) will not be displayed, indicating that the gateway function equipped ECU is not communicating with the central gateway ECU (network gateway ECU).

·

The malfunctioning part can be determined by inspecting for an open in the main bus line, a short between bus lines or a short to +B or ground.

·

Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.




c.

Problem Symptom Pattern B

Display on Communication Bus Check Screen ECUs or sensors farther from the central gateway ECU (network gateway ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen.
Details of Malfunction Open in both wires of the main bus line between the CGW and No. 1 CAN junction connector in Bus 2

C416690C01
6.406,3.906 6.865,4.104 0.458,0.198 10 false ENG 2.448,4.5 2.906,4.698 0.458,0.198 10 false BRK 2.063,3.333 2.583,3.542 0.521,0.208 10 false F-MGC 1.854,4.5 2.313,4.698 0.458,0.198 10 false HV 4.313,3.333 4.896,3.573 0.583,0.24 10 false R-MGC 3.75,3.333 4.208,3.531 0.458,0.198 10 false HVB 1.844,5.75 2.302,5.948 0.458,0.198 10 false MB 1.521,7.188 1.979,7.385 0.458,0.198 10 false DLC3 6.458,6.521 6.917,6.719 0.458,0.198 10 false ST 3.052,7.135 3.563,7.365 0.51,0.229 10 false MIR-R 1.938,3.927 2.885,4.125 0.948,0.198 10 false CAN J/C 1 4.979,7.135 5.479,7.354 0.5,0.219 10 false MIR-L 3.729,5.708 4.188,5.906 0.458,0.198 10 false EPS 5.729,5.083 6.188,5.281 0.458,0.198 10 false SRS 4.375,5.698 4.833,5.896 0.458,0.198 10 false STR 0.458,5.354 0.917,5.552 0.458,0.198 10 false CGW 1,3.729 1.354,3.948 0.354,0.219 10 false *a 3.865,3.927 4.813,4.125 0.948,0.198 10 false CAN J/C 2 1.927,5.094 2.875,5.292 0.948,0.198 10 false CAN J/C 3 2.906,6.521 3.854,6.719 0.948,0.198 10 false CAN J/C 5 3.865,5.094 4.813,5.292 0.948,0.198 10 false CAN J/C 4 4.833,6.531 5.781,6.729 0.948,0.198 10 false CAN J/C 6 1.021,4.896 1.323,5.115 0.302,0.219 10 false *b 1.698,6.167 2.156,6.365 0.458,0.198 10 false *c 1,7.063 1.385,7.271 0.385,0.208 10 false *d 5.563,3.188 6.021,3.385 0.458,0.198 10 false : *e 0.375,0.792 0.833,0.99 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction (open in both wires of the main bus line) *f Background color is red


HINT:
·

Due to the malfunction, almost all of the ECUs and sensors connected to Bus 2 will be displayed as not communicating and their background color will be red.

·

The malfunction in Bus 2 will not affect the other buses.

·

The malfunctioning part can be determined by inspecting for an open in the main bus line.

·

Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.



Display on Communication Bus Check Screen ECUs or sensors farther from the central gateway ECU (network gateway ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen.
Details of Malfunction Open in both wires of the main bus line between the No. 1 CAN junction connector and No. 2 CAN junction connector in Bus 2

C416691C01
0.458,5.448 0.917,5.646 0.458,0.198 10 false CGW 2.052,3.344 2.646,3.583 0.594,0.24 10 false F-MGC 3.74,3.333 4.198,3.531 0.458,0.198 10 false HVB 4.302,3.344 4.844,3.604 0.542,0.26 10 false R-MGC 6.406,3.906 6.865,4.104 0.458,0.198 10 false ENG 1.854,4.5 2.313,4.698 0.458,0.198 10 false HV 2.448,4.51 2.906,4.708 0.458,0.198 10 false BRK 1.844,5.75 2.302,5.948 0.458,0.198 10 false MB 1.51,7.188 1.969,7.385 0.458,0.198 10 false DLC3 3.052,7.146 3.563,7.354 0.51,0.208 10 false MIR-R 4.979,7.146 5.438,7.344 0.458,0.198 10 false MIR-L 6.469,6.531 6.927,6.729 0.458,0.198 10 false ST 5.729,5.083 6.188,5.281 0.458,0.198 10 false SRS 4.385,5.688 4.844,5.885 0.458,0.198 10 false STR 3.74,5.698 4.198,5.896 0.458,0.198 10 false EPS 1.938,3.927 2.833,4.115 0.896,0.188 10 false CAN J/C 1 3.854,3.927 4.75,4.115 0.896,0.188 10 false CAN J/C 2 1.927,5.094 2.823,5.281 0.896,0.188 10 false CAN J/C 3 3.865,5.083 4.76,5.271 0.896,0.188 10 false CAN J/C 4 2.896,6.542 3.792,6.729 0.896,0.188 10 false CAN J/C 5 4.833,6.531 5.729,6.719 0.896,0.188 10 false CAN J/C 6 5.594,3.24 6.052,3.438 0.458,0.198 10 false : *e 1,3.719 1.458,3.938 0.458,0.219 10 false *a 1,4.896 1.448,5.115 0.448,0.219 10 false *b 1.698,6.156 2.156,6.354 0.458,0.198 10 false *c 1,7.063 1.458,7.26 0.458,0.198 10 false *d 0.531,0.99 0.99,1.188 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction (open in both wires of the main bus line) *f Background color is red


HINT:
·

Due to the malfunction, ECUs or sensors farther from the CGW than the open in the wires will be displayed as not communicating and their background color will be red.

·

The malfunction in Bus 2 will not affect the other buses.

·

The malfunctioning part can be determined by inspecting for an open in the main bus line.

·

Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.



Display on Communication Bus Check Screen ECUs or sensors farther from the central gateway ECU (network gateway ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen.
Details of Malfunction Open in both wires of the main bus line between the No. 2 CAN junction connector and ENG in Bus 2

C416692C01
2.688,1.563 2.604,0.229 2.604,0.229 2.354,0.229 true 4.906,1.469 5.042,0.229 5.042,0.229 5.292,0.229 true 0.448,5.302 0.906,5.5 0.458,0.198 10 false CGW 2.052,3.344 2.604,3.573 0.552,0.229 10 false F-MGC 3.74,3.354 4.198,3.552 0.458,0.198 10 false HVB 4.302,3.344 4.813,3.583 0.51,0.24 10 false R-MGC 6.396,3.927 6.854,4.125 0.458,0.198 10 false ENG 1.854,4.51 2.313,4.708 0.458,0.198 10 false HV 2.448,4.51 2.906,4.708 0.458,0.198 10 false BRK 1.854,5.75 2.313,5.948 0.458,0.198 10 false MB 5.729,5.094 6.188,5.292 0.458,0.198 10 false SRS 4.396,5.698 4.854,5.896 0.458,0.198 10 false STR 3.729,5.708 4.188,5.906 0.458,0.198 10 false EPS 1.51,7.198 1.969,7.396 0.458,0.198 10 false DLC3 3.063,7.135 3.625,7.375 0.563,0.24 10 false MIR-R 4.99,7.135 5.51,7.354 0.521,0.219 10 false MIR-L 6.469,6.531 6.927,6.729 0.458,0.198 10 false ST 1.927,3.927 2.708,4.125 0.781,0.198 10 false CAN J/C 1 3.896,3.927 4.677,4.125 0.781,0.198 10 false CAN J/C 2 1.948,5.094 2.729,5.292 0.781,0.198 10 false CAN J/C 3 3.875,5.094 4.656,5.292 0.781,0.198 10 false CAN J/C 4 2.906,6.542 3.688,6.74 0.781,0.198 10 false CAN J/C 5 4.833,6.542 5.615,6.74 0.781,0.198 10 false CAN J/C 6 1.01,3.74 1.396,3.938 0.385,0.198 10 false *a 1.01,4.906 1.396,5.104 0.385,0.198 10 false *b 1.698,6.156 2.156,6.354 0.458,0.198 10 false *c 1.021,7.073 1.365,7.26 0.344,0.188 10 false *d 5.771,3.198 6.229,3.396 0.458,0.198 10 false : *e 0.115,0.375 0.646,0.594 0.531,0.219 10 false *g 3.677,0.385 3.99,0.604 0.313,0.219 10 false *h 2.188,0.167 2.646,0.365 0.458,0.198 10 false *f 5.333,0.156 5.792,0.354 0.458,0.198 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction (open in both wires of the main bus line) *f Background color is red
*g Pattern 1 *h Pattern 2


HINT:
·

Even when the same part of the main bus line is open, depending on internal electrical noise which changes according to the position of the open in the line, the information displayed on the "Communication Bus Check" screen may differ.

·

In pattern 2, the information displayed may be the same as when there is an open in both wires in the main bus line between the No. 1 CAN junction connector and No. 2 CAN junction connector, which may make it difficult to determine the malfunctioning part.

·

The malfunction in Bus 2 will not affect the other buses.

·

Make sure to perform the inspection to measure resistances of buses to determine the cause of the malfunction.




d.

Problem Symptom Pattern C

Display on Communication Bus Check Screen One ECU or sensor is displayed as not communicating on the "Communication Bus Check" screen.
Details of Malfunction
·

Open in both wires of the branch line connected to F-MGC in Bus 2

·

Internal malfunction of F-MGC in Bus 2

·

Malfunction in the power supplied to F-MGC in Bus 2



C416693C01
0.458,5.375 0.917,5.573 0.458,0.198 10 false CGW 2.052,3.344 2.604,3.563 0.552,0.219 10 false F-MGC 3.74,3.344 4.198,3.542 0.458,0.198 10 false HVB 4.313,3.354 4.885,3.625 0.573,0.271 10 false R-MGC 6.417,3.917 6.875,4.115 0.458,0.198 10 false ENG 1.865,4.51 2.323,4.708 0.458,0.198 10 false HV 2.438,4.51 2.896,4.708 0.458,0.198 10 false BRK 1.844,5.76 2.302,5.958 0.458,0.198 10 false MB 1.51,7.198 1.969,7.396 0.458,0.198 10 false DLC3 3.063,7.135 3.635,7.354 0.573,0.219 10 false MIR-R 3.74,5.719 4.198,5.917 0.458,0.198 10 false EPS 4.396,5.708 4.854,5.906 0.458,0.198 10 false STR 5.729,5.083 6.188,5.281 0.458,0.198 10 false SRS 6.448,6.542 6.906,6.74 0.458,0.198 10 false ST 4.979,7.135 5.448,7.365 0.469,0.229 10 false MIR-L 1.938,3.938 2.896,4.125 0.958,0.188 10 false CAN J/C 1 3.865,3.927 4.823,4.115 0.958,0.188 10 false CAN J/C 2 1.958,5.104 2.917,5.292 0.958,0.188 10 false CAN J/C 3 3.885,5.104 4.844,5.292 0.958,0.188 10 false CAN J/C 4 2.906,6.51 3.865,6.698 0.958,0.188 10 false CAN J/C 5 4.844,6.531 5.802,6.719 0.958,0.188 10 false CAN J/C 6 1,3.708 1.542,3.938 0.542,0.229 10 false *a 1,4.927 1.375,5.125 0.375,0.198 10 false *b 1.688,6.156 2.146,6.354 0.458,0.198 10 false *c 1,7.073 1.354,7.271 0.354,0.198 10 false *d 5.823,3.26 6.281,3.458 0.458,0.198 10 false : *e 0.323,0.385 0.781,0.583 0.458,0.198 10 false *f 5.823,3.521 6.281,3.719 0.458,0.198 10 false : *g
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction 1 (open in both wires of the branch line) *f Background color is red
*g Location of malfunction 2
·

Internal malfunction

·

Power source malfunction


- -


HINT:

The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor, or a malfunction in the power supplied to an ECU or sensor. In this example, the background color of the malfunctioning ECU or sensor will be red.


Display on Communication Bus Check Screen One ECU or sensor is displayed as not communicating on the "Communication Bus Check" screen.
Details of Malfunction Open in both wires of the branch line connected to ENG in Bus 4

C416694C01
0.469,5.302 0.927,5.5 0.458,0.198 10 false CGW 2.063,3.333 2.625,3.573 0.563,0.24 10 false F-MGC 3.75,3.344 4.208,3.542 0.458,0.198 10 false HVB 4.313,3.344 4.865,3.583 0.552,0.24 10 false R-MGC 6.417,3.906 6.875,4.104 0.458,0.198 10 false ENG 1.865,4.5 2.323,4.698 0.458,0.198 10 false HV 2.448,4.5 2.906,4.698 0.458,0.198 10 false BRK 1.854,5.75 2.313,5.948 0.458,0.198 10 false MB 1.51,7.198 1.969,7.396 0.458,0.198 10 false DLC3 3.052,7.135 3.594,7.365 0.542,0.229 10 false MIR-R 4.979,7.125 5.51,7.344 0.531,0.219 10 false MIR-L 6.458,6.51 6.917,6.708 0.458,0.198 10 false ST 5.74,5.083 6.198,5.281 0.458,0.198 10 false SRS 4.396,5.698 4.854,5.896 0.458,0.198 10 false STR 3.74,5.698 4.198,5.896 0.458,0.198 10 false EPS 1.948,3.917 2.729,4.125 0.781,0.208 10 false CAN J/C 1 3.885,3.927 4.667,4.135 0.781,0.208 10 false CAN J/C 2 1.948,5.094 2.729,5.302 0.781,0.208 10 false CAN J/C 3 3.896,5.083 4.677,5.292 0.781,0.208 10 false CAN J/C 4 2.917,6.531 3.698,6.74 0.781,0.208 10 false CAN J/C 5 4.823,6.521 5.604,6.729 0.781,0.208 10 false CAN J/C 6 1,3.719 1.375,3.938 0.375,0.219 10 false *a 0.99,4.906 1.385,5.115 0.396,0.208 10 false *b 1.708,6.135 2.01,6.365 0.302,0.229 10 false *c 1,7.052 1.5,7.292 0.5,0.24 10 false *d 5.688,3.25 5.99,3.479 0.302,0.229 10 false : *e 0.292,1.385 0.594,1.615 0.302,0.229 10 false *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction (open in both wires of the branch line) *f Background color is red


HINT:
·

The malfunction in Bus 4 will not affect the other buses.

·

Due to the malfunction, although ENG is communicating normally with CGW via Bus 2, it is not communicating with CGW via Bus 4. Consequently, it will be displayed as not communicating in Bus 4.




e.

Problem Symptom Pattern D

Display on Communication Bus Check Screen
·

No ECUs or sensors are displayed on the "Communication Bus Check" screen.

·

All ECUs or sensors are displayed as not communicating on the "Communication Bus Check" screen.


Details of Malfunction
·

Internal malfunction of CGW

·

Malfunction in the power supplied to CGW

·

Open in both wires of the branch lines in the diagnosis bus



C416695C01
4.844,1.563 5.198,0.313 5.198,0.313 5.385,0.313 true 0.458,5.313 0.917,5.51 0.458,0.198 10 false CGW 2.063,3.24 2.594,3.469 0.531,0.229 10 false F-MGC 3.74,3.24 4.198,3.438 0.458,0.198 10 false HVB 4.313,3.26 4.854,3.469 0.542,0.208 10 false R-MGC 6.396,3.813 6.854,4.01 0.458,0.198 10 false ENG 2.458,4.406 2.917,4.604 0.458,0.198 10 false BRK 1.844,4.406 2.302,4.604 0.458,0.198 10 false HV 1.833,5.646 2.292,5.844 0.458,0.198 10 false MB 3.052,7.052 3.563,7.271 0.51,0.219 10 false MIR-R 4.979,7.042 5.49,7.26 0.51,0.219 10 false MIR-L 6.469,6.438 6.927,6.635 0.458,0.198 10 false ST 1.521,7.083 1.979,7.281 0.458,0.198 10 false DLC3 3.74,5.604 4.198,5.802 0.458,0.198 10 false EPS 4.385,5.594 4.844,5.792 0.458,0.198 10 false STR 5.729,4.979 6.188,5.177 0.458,0.198 10 false SRS 1.948,3.823 2.823,4.021 0.875,0.198 10 false CAN J/C 1 1.073,3.635 1.406,3.844 0.333,0.208 10 false *a 3.854,3.823 4.729,4.021 0.875,0.198 10 false CAN J/C 2 1.938,5 2.813,5.198 0.875,0.198 10 false CAN J/C 3 3.885,5 4.76,5.198 0.875,0.198 10 false CAN J/C 4 2.906,6.438 3.781,6.635 0.875,0.198 10 false CAN J/C 5 4.823,6.427 5.698,6.625 0.875,0.198 10 false CAN J/C 6 1.083,4.823 1.469,5.01 0.385,0.188 10 false *b 1.719,6.052 2.177,6.25 0.458,0.198 10 false *c 1.083,6.875 1.365,7.104 0.281,0.229 10 false *d 5.823,3.427 6.281,3.625 0.458,0.198 10 false : *g 0.094,1.656 0.365,1.948 0.271,0.292 10 false *f 5.823,3.146 6.281,3.344 0.458,0.198 10 false : *e 0.094,0.406 0.406,0.604 0.313,0.198 10 false *i 3.646,0.396 3.958,0.594 0.313,0.198 10 false *j 5.427,0.229 5.74,0.427 0.313,0.198 10 false *h
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction 1 (open in both wires of the branch line) *f Not displayed
*g Location of malfunction 2 (Internal malfunction) *h Background color is red
*i Pattern 1 (Malfunction occurred before CAN bus check) *j Pattern 2 (Malfunction occurred after CAN bus check)


HINT:

When there is no communication between the GTS and the vehicle, no ECUs or sensors will be displayed.



f.

Problem Symptom Pattern E

Display on Communication Bus Check Screen One ECU or sensor is displayed as not communicating in multiple buses on the "Communication Bus Check" screen.
Details of Malfunction
·

Internal malfunction of BRK

·

Malfunction in the power supplied to BRK



C416696C01
0.448,5.563 0.906,5.76 0.458,0.198 10 false CGW 2.063,3.469 2.615,3.708 0.552,0.24 10 false F-MGC 3.729,3.469 4.188,3.667 0.458,0.198 10 false HVB 4.313,3.479 4.875,3.74 0.563,0.26 10 false R-MGC 6.406,4.042 6.865,4.24 0.458,0.198 10 false ENG 1.854,4.625 2.313,4.823 0.458,0.198 10 false HV 2.5,4.615 2.958,4.813 0.458,0.198 10 false BRK 1.844,5.865 2.302,6.063 0.458,0.198 10 false MB 3.74,5.823 4.198,6.021 0.458,0.198 10 false EPS 4.385,5.823 4.844,6.021 0.458,0.198 10 false STR 5.729,5.219 6.188,5.417 0.458,0.198 10 false SRS 6.479,6.656 6.938,6.854 0.458,0.198 10 false ST 4.979,7.25 5.49,7.458 0.51,0.208 10 false MIR-L 3.052,7.26 3.542,7.5 0.49,0.24 10 false MIR-R 1.521,7.323 1.979,7.521 0.458,0.198 10 false DLC3 1.938,4.042 2.781,4.24 0.844,0.198 10 false CAN J/C 1 0.99,3.865 1.448,4.063 0.458,0.198 10 false *a 1,5.042 1.458,5.24 0.458,0.198 10 false *b 1.677,6.281 2.135,6.479 0.458,0.198 10 false *c 0.99,7.198 1.448,7.396 0.458,0.198 10 false *d 5.823,3.344 6.281,3.542 0.458,0.198 10 false : *e 0.198,0.573 0.656,0.771 0.458,0.198 10 false *f 0.208,2.26 0.667,2.458 0.458,0.198 10 false *f 3.875,4.052 4.719,4.25 0.844,0.198 10 false CAN J/C 2 1.938,5.219 2.781,5.417 0.844,0.198 10 false CAN J/C 3 3.875,5.208 4.719,5.406 0.844,0.198 10 false CAN J/C 4 2.906,6.656 3.75,6.854 0.844,0.198 10 false CAN J/C 5 4.802,6.656 5.646,6.854 0.844,0.198 10 false CAN J/C 6
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction
·

Internal malfunction

·

Power source malfunction


*f Background color is red


HINT:

The information displayed on the "Communication Bus Check" screen will be the same for an internal malfunction of an ECU or sensor, or a malfunction in the power supplied to an ECU or sensor.

Due to the malfunction, BRK is not communicating with CGW via both Bus 2 and Bus 4. Consequently, the background color of BRK will be red for both Bus 2 and Bus 4.



g.

Problem Symptom Pattern F

Display on Communication Bus Check Screen Some ECUs or sensors are displayed as not communicating in the central bus and other ECUs or sensors are displayed as not communicating in a sub bus.
Details of Malfunction
·

Open in a wire of the branch line connected to HV in Bus 4

·

Internal malfunction of HV in Bus 4



C416697C01
0.458,5.25 0.917,5.448 0.458,0.198 10 false CGW 2.063,3.344 2.625,3.583 0.563,0.24 10 false F-MGC 1.854,4.479 2.313,4.677 0.458,0.198 10 false HV 2.448,4.479 2.906,4.677 0.458,0.198 10 false BRK 3.729,3.344 4.188,3.542 0.458,0.198 10 false HVB 4.313,3.344 4.906,3.604 0.594,0.26 10 false R-MGC 6.417,3.906 6.875,4.104 0.458,0.198 10 false ENG 6.469,6.521 6.927,6.719 0.458,0.198 10 false ST 5.729,5.083 6.188,5.281 0.458,0.198 10 false SRS 1.844,5.74 2.302,5.938 0.458,0.198 10 false MB 1.521,7.188 1.979,7.385 0.458,0.198 10 false DLC3 3.063,7.135 3.542,7.354 0.479,0.219 10 false MIR-R 3.729,5.698 4.188,5.896 0.458,0.198 10 false EPS 4.396,5.698 4.854,5.896 0.458,0.198 10 false STR 4.99,7.135 5.448,7.333 0.458,0.198 10 false MIR-L 1.927,3.927 2.792,4.125 0.865,0.198 10 false CAN J/C 1 1,3.74 1.458,3.938 0.458,0.198 10 false *a 1,4.917 1.458,5.115 0.458,0.198 10 false *b 1.688,6.167 2.146,6.365 0.458,0.198 10 false *c 0.99,7.073 1.448,7.271 0.458,0.198 10 false *d 0.25,1.365 0.698,1.573 0.448,0.208 10 false *g 0.24,1.604 0.698,1.802 0.458,0.198 10 false *h 0.281,2.604 0.74,2.802 0.458,0.198 10 false *i 5.823,3.24 6.281,3.438 0.458,0.198 10 false : *e 3.865,3.927 4.729,4.125 0.865,0.198 10 false CAN J/C 2 1.927,5.094 2.792,5.292 0.865,0.198 10 false CAN J/C 3 3.875,5.083 4.74,5.281 0.865,0.198 10 false CAN J/C 4 2.906,6.531 3.771,6.729 0.865,0.198 10 false CAN J/C 5 4.813,6.531 5.677,6.729 0.865,0.198 10 false CAN J/C 6 5.823,3.521 6.281,3.719 0.458,0.198 10 false : *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction 1 (open in a wire of the branch line) *f Location of malfunction 2
·

Internal malfunction

·

Power source malfunction


*g Background color is red *h Background color intermittently becomes yellow or red
*i Not displayed or background color is yellow or red - -


HINT:
·

In the "Communication Bus Check" screen shown in the illustration, electrical noise in the CAN bus caused by an open in a wire in the branch line connected to HV interferes with the communication of MB causing unstable communication. Also, since MB is a gateway function equipped ECU, communication of ECUs connected to its respective sub bus will also be unstable.

·

In the "Communication Bus Check" screen shown in the illustration, because the background color of HV is red, it is suspected that HV is the most likely cause of the malfunction. Therefore, it is suspected that HV is not communicating.




h.

Problem Symptom Pattern G

Display on Communication Bus Check Screen A gateway function equipped ECU is displayed as not communicating in the central bus and ECUs, and sensors connected to its respective sub bus are not displayed.
Details of Malfunction
·

Open in both wires of the branch line connected to MB in Bus 4

·

Internal malfunction of MB in Bus 4

·

Malfunction in the power supplied to MB in Bus 4



C416698C01
0.458,5.281 0.917,5.479 0.458,0.198 10 false CGW 2.052,3.354 2.646,3.594 0.594,0.24 10 false F-MGC 1.854,4.51 2.313,4.708 0.458,0.198 10 false HV 2.458,4.51 2.917,4.708 0.458,0.198 10 false BRK 3.74,3.344 4.198,3.542 0.458,0.198 10 false HVB 4.302,3.354 4.833,3.573 0.531,0.219 10 false R-MGC 6.406,3.927 6.865,4.125 0.458,0.198 10 false ENG 5.729,5.083 6.188,5.281 0.458,0.198 10 false SRS 4.385,5.708 4.844,5.906 0.458,0.198 10 false STR 3.74,5.719 4.198,5.917 0.458,0.198 10 false EPS 1.854,5.729 2.313,5.927 0.458,0.198 10 false MB 1.521,7.208 1.979,7.406 0.458,0.198 10 false DLC3 3.052,7.146 3.552,7.396 0.5,0.25 10 false MIR-R 4.979,7.146 5.469,7.344 0.49,0.198 10 false MIR-L 6.469,6.531 6.927,6.729 0.458,0.198 10 false ST 1.938,3.927 2.719,4.135 0.781,0.208 10 false CAN J/C 1 1,3.75 1.458,3.948 0.458,0.198 10 false *a 3.865,3.927 4.646,4.135 0.781,0.208 10 false CAN J/C 2 1.938,5.094 2.719,5.302 0.781,0.208 10 false CAN J/C 3 3.875,5.104 4.656,5.313 0.781,0.208 10 false CAN J/C 4 2.906,6.531 3.688,6.74 0.781,0.208 10 false CAN J/C 5 4.854,6.542 5.635,6.75 0.781,0.208 10 false CAN J/C 6 1,4.917 1.458,5.115 0.458,0.198 10 false *b 1,7.073 1.458,7.271 0.458,0.198 10 false *d 1.667,6.167 2.125,6.365 0.458,0.198 10 false *c 0.469,1.615 0.927,1.813 0.458,0.198 10 false *g 5.813,3.208 6.271,3.406 0.458,0.198 10 false : *e 0.448,2.479 0.906,2.677 0.458,0.198 10 false *h 5.813,3.531 6.271,3.729 0.458,0.198 10 false : *f
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction 1 (open in both wires of the branch line) *f Location of malfunction 2
·

Internal malfunction

·

Power source malfunction


*g Background color is red *h Not displayed


HINT:
·

If there is a communication malfunction in a gateway function equipped ECU, ECUs connected to its respective sub bus will also be affected and will not be displayed.

·

In the "Communication Bus Check" screen shown in the illustration, MB is a gateway function equipped ECU. Therefore, MB is suspected as not communicating.




i.

Problem Symptoms Pattern H

Display on Communication Bus Check Screen One ECU or sensor is displayed as not communicating in a sub bus on the "Communication Bus Check" screen.
Details of Malfunction
·

Internal malfunction of MIR-L in the sub bus

·

Malfunction in the power supplied to MIR-L in the sub bus

·

Open in both wires of the branch line connected to MIR-L in the sub bus



C416699C01
0.469,5.313 0.927,5.51 0.458,0.198 10 false CGW 2.063,3.344 2.656,3.583 0.594,0.24 10 false F-MGC 3.729,3.344 4.188,3.542 0.458,0.198 10 false HVB 4.313,3.333 4.896,3.604 0.583,0.271 10 false R-MGC 1.854,4.5 2.313,4.698 0.458,0.198 10 false HV 2.469,4.5 2.927,4.698 0.458,0.198 10 false BRK 6.417,3.906 6.875,4.104 0.458,0.198 10 false ENG 1.844,5.75 2.302,5.948 0.458,0.198 10 false MB 3.75,5.698 4.208,5.896 0.458,0.198 10 false EPS 4.396,5.698 4.854,5.896 0.458,0.198 10 false STR 5.729,5.083 6.188,5.281 0.458,0.198 10 false SRS 3.063,7.146 3.635,7.417 0.573,0.271 10 false MIR-R 1.521,7.188 1.979,7.385 0.458,0.198 10 false DLC3 4.969,7.125 5.458,7.333 0.49,0.208 10 false MIR-L 6.458,6.521 6.917,6.719 0.458,0.198 10 false ST 1.958,3.917 2.781,4.125 0.823,0.208 10 false CAN J/C 1 1,3.75 1.458,3.948 0.458,0.198 10 false *a 1,4.917 1.458,5.115 0.458,0.198 10 false *b 1.698,6.156 2.156,6.354 0.458,0.198 10 false *c 0.99,7.073 1.448,7.271 0.458,0.198 10 false *d 5.813,3.521 6.271,3.719 0.458,0.198 10 false : *f 0.271,2.656 0.729,2.854 0.458,0.198 10 false *g 3.875,3.927 4.698,4.115 0.823,0.188 10 false CAN J/C 2 1.948,5.083 2.781,5.302 0.833,0.219 10 false CAN J/C 3 4.844,6.521 5.625,6.74 0.781,0.219 10 false CAN J/C 6 3.854,5.083 4.656,5.25 0.802,0.167 10 false CAN J/C 4 2.917,6.531 3.729,6.76 0.813,0.229 10 false CAN J/C 5 5.813,3.24 6.271,3.438 0.458,0.198 10 false : *e
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction 1 (open in both wires of the branch line) *f Location of malfunction 2
·

Internal malfunction

·

Power source malfunction


*g Background color is red - -


HINT:
·

The malfunction in the sub bus will not affect the other buses.

·

When a gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus and there is a communication malfunction in one of the ECUs or sensors, the background color of the ECU or sensor will change to red and the ECU or sensor will remain displayed.

·

The information displayed on the "Communication Bus Check" screen will be the same for an open in both wires of a branch line, an internal malfunction of an ECU or sensor or a malfunction in the power supplied to an ECU or sensor.




j.

Problem Symptom Pattern I

Display on Communication Bus Check Screen ECUs or sensors farther from the sub bus monitoring ECU (gateway function equipped ECU) than the open in the wires are displayed as not communicating on the "Communication Bus Check" screen.
Details of Malfunction Open in both wires of the main bus line in the sub bus

C416700C01
0.458,5.375 0.917,5.573 0.458,0.198 10 false CGW 2.063,3.344 2.667,3.604 0.604,0.26 10 false F-MGC 3.74,3.344 4.198,3.542 0.458,0.198 10 false HVB 4.302,3.344 4.938,3.583 0.635,0.24 10 false R-MGC 6.406,3.906 6.865,4.104 0.458,0.198 10 false ENG 1.865,4.5 2.323,4.698 0.458,0.198 10 false HV 2.448,4.5 2.906,4.698 0.458,0.198 10 false BRK 1.833,5.74 2.292,5.938 0.458,0.198 10 false MB 3.74,5.698 4.198,5.896 0.458,0.198 10 false EPS 4.396,5.698 4.854,5.896 0.458,0.198 10 false STR 5.729,5.094 6.188,5.292 0.458,0.198 10 false SRS 6.479,6.531 6.938,6.729 0.458,0.198 10 false ST 3.063,7.135 3.583,7.406 0.521,0.271 10 false MIR-R 4.979,7.135 5.479,7.333 0.5,0.198 10 false MIR-L 1.521,7.198 1.979,7.396 0.458,0.198 10 false DLC3 1.958,3.917 2.813,4.115 0.854,0.198 10 false CAN J/C 1 0.99,3.74 1.448,3.938 0.458,0.198 10 false *a 5.646,3.229 6.104,3.427 0.458,0.198 10 false : *e 0.99,4.917 1.448,5.115 0.458,0.198 10 false *b 1.688,6.135 2.146,6.333 0.458,0.198 10 false *c 1,7.083 1.458,7.281 0.458,0.198 10 false *d 0.281,2.677 0.74,2.875 0.458,0.198 10 false *f 3.844,3.917 4.698,4.115 0.854,0.198 10 false CAN J/C 2 1.938,5.094 2.792,5.292 0.854,0.198 10 false CAN J/C 3 3.865,5.083 4.719,5.281 0.854,0.198 10 false CAN J/C 4 2.917,6.531 3.771,6.729 0.854,0.198 10 false CAN J/C 5 4.833,6.531 5.688,6.729 0.854,0.198 10 false CAN J/C 6
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction (open in both wires of the main bus line) *f Background color is red


HINT:

Due to the malfunction, ECUs or sensors farther from the sub bus monitoring ECU (gateway function equipped ECU) than the open in the wires will be displayed as not communicating and their background color will be red.




How to Use "Communication Bus check (Detail)" Screen in Inspection


a.

If the CAN communication system is currently normal but has communication stop history, determine the malfunctioning part using Communication Bus Check (Detail) as follows:

NOTICE:
·

The following CAN bus wiring diagram or communication bus check screen is provided only as an example. This wiring diagram or screen differs from the actual one for this vehicle.

·

The Lost Communication Time column displays the longest period of time in seconds that the central gateway ECU (network gateway ECU) detected a communication stop in the respective ECU or sensor.

·

The Lost Communication Trip column displays the trip in which the central gateway ECU (network gateway ECU) detected the longest communication stop in the respective ECU or sensor.

·

When using the combo box, it may be possible to select a sub bus from the drop down list that does not have any connected ECUs or sensors. This is not a malfunction and occurs when there is no optional device connected to a sub bus which is monitored by a sub bus monitoring ECU (gateway function equipped ECU).

·

In the drop down list, all sub buses applicable to the model are displayed (e.g. LIN communication sub buses are also displayed). For information on sub buses necessary to diagnose the CAN communication system, refer to the System Diagram.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM



HINT:
·

If the CAN communication system is currently malfunctioning, it is recommended to use Communication Bus Check rather than Communication Bus Check (Detail) for determining the suspected area.

·

The communication error history of ECUs or sensors which have communication error history can be displayed on the "Communication Bus Check (Detail)" screen.

·

Lost Communication Time and Lost Communication Trip are only displayed for the central bus.

·

Lost Communication Time and Lost Communication Trip are not displayed for sub buses.




b.

If there is an ECU or sensor displayed with a red background on the "Communication Bus Check (Detail)" screen to indicate that it was not communicating, it is suspected that the ECU or sensor was not communicating.

Details of Malfunction Past malfunction in the wire harness or power supplied to F-MGC in Bus 2

C416701C01
0.458,5.5 0.917,5.698 0.458,0.198 10 false CGW 2.052,3.5 2.615,3.729 0.563,0.229 10 false F-MGC 3.74,3.5 4.198,3.698 0.458,0.198 10 false HVB 4.313,3.5 4.906,3.75 0.594,0.25 10 false R-MGC 6.406,4.073 6.865,4.271 0.458,0.198 10 false ENG 5.74,5.25 6.198,5.448 0.458,0.198 10 false SRS 2.458,4.667 2.917,4.865 0.458,0.198 10 false BRK 1.854,4.667 2.313,4.865 0.458,0.198 10 false HV 1.854,5.906 2.313,6.104 0.458,0.198 10 false MB 1.521,7.354 1.979,7.552 0.458,0.198 10 false DLC3 3.052,7.292 3.583,7.552 0.531,0.26 10 false MIR-R 4.979,7.292 5.469,7.521 0.49,0.229 10 false MIR-L 6.469,6.688 6.927,6.885 0.458,0.198 10 false ST 4.385,5.854 4.844,6.052 0.458,0.198 10 false STR 3.74,5.865 4.198,6.063 0.458,0.198 10 false EPS 1.958,4.073 2.74,4.292 0.781,0.219 10 false CAN J/C 1 1,3.896 1.458,4.094 0.458,0.198 10 false *a 0.99,5.073 1.448,5.271 0.458,0.198 10 false *b 1.698,6.313 2.156,6.51 0.458,0.198 10 false *c 0.979,7.229 1.438,7.427 0.458,0.198 10 false *d 0.781,2.854 1.24,3.052 0.458,0.198 10 false : *e 2.615,0.948 3.073,1.146 0.458,0.198 10 false *f 3.885,4.083 4.646,4.302 0.76,0.219 10 false CAN J/C 2 1.948,5.24 2.76,5.51 0.813,0.271 10 false CAN J/C 3 3.906,5.24 4.688,5.479 0.781,0.24 10 false CAN J/C 4 2.927,6.688 3.76,6.917 0.833,0.229 10 false CAN J/C 5 4.844,6.698 5.625,6.969 0.781,0.271 10 false CAN J/C 6
*a Bus 2 *b Bus 4
*c Sub bus *d Diagnosis bus
*e Location of malfunction
·

Internal malfunction

·

Power source malfunction


*f Background color is red


Description of "Communication Bus Check (Detail)" Screen
Bus Type Background Color Connection Status
Bus White Either of the following:
·

Communication has been normal.

·

Lost Communication Time is below 6 seconds.


Red Lost Communication Time is 6 seconds or more.
Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*1

·

No ECUs or sensors are connected to the bus.*2


Sub bus White Lost Communication Time is displayed as "-".
Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU.*3

·

No ECUs or sensors are connected to the sub bus.*4



HINT:
·

Check the values of Lost Communication Trip and Current Trip for the ECUs or sensors that have a red background color.

·

If the values of Lost Communication Trip and Current Trip are the same for an ECU or sensor, the ECU or sensor is currently not communicating. In this case, it is recommended to use Communication Bus Check rather than Communication Bus Check (Detail) for determining the suspected area.

·

In the "Communication Bus Check (Detail)" screen shown in the illustration, F-MGC had a communication malfunction in the 10th trip. Thus, it is suspected that F-MGC was not communicating.

·

*1: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the names of buses, sub buses, ECUs and sensors will not be displayed.

·

*2: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*3: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the names of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*4: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.





DTC TABLE BY ECU


HINT:
·

In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.

·

If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If there is a malfunction currently, DTCs can be checked by performing steps in the DTC check procedure.



a.

EV Control ECU / GTS Display "EV"

HINT:
·

DTC communication uses the CAN communication system.



Powertrain > EV > Trouble Codes
50001 397
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010387* Lost Communication with Gear Shift Control Module "A" (Hybrid/EV Battery Local Bus) Missing Message Communication stop occurs between the EV control ECU and shift control ECU continuously for 1 second or more. All conditions are met:
·

1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the EV control ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the EV control ECU and airbag ECU assembly continuously for 1 second or more. All conditions are met:
·

1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the EV control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the EV control ECU and steering sensor continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the EV control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. - - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the EV control ECU and brake actuator assembly (No. 2 skid control ECU) ECU assembly continuously for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the EV control ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the EV control ECU and main body ECU (multiplex network body ECU) continuously for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the EV control ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 10 seconds. - - DTC is stored until it is cleared using the GTS.
U015187 Lost Communication with Restraints Control Module Missing Message Communication stop occurs between the EV control ECU and airbag ECU assembly continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the EV control ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 15 seconds. - - DTC is stored until it is cleared using the GTS.
U016487 Lost Communication with HVAC Control Module Missing Message Communication stop occurs between the EV control ECU and air conditioning amplifier assembly continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the EV control ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 15 seconds. - - DTC is stored until it is cleared using the GTS.
U110787 Lost Communication with Power Management Module Missing Message Communication stop occurs between the EV control ECU and certification ECU (smart key ECU assembly) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the EV control ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U117087 Lost Communication with Brake System Control Module (Secondary CAN Line) Missing Message Communication stop occurs between the EV control ECU and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the EV control ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC is stored until it is cleared using the GTS.
U117587 Lost Communication with Hybrid/EV Battery Energy Control Module "A" (Powertrain Bus) Missing Message Communication stop occurs between the EV control ECU and battery ECU assembly continuously for approximately 51 seconds or more. All conditions are met:
·

1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the EV control ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 60 seconds. MIL (Check engine warning light) illuminates. - DTC is stored until it is cleared using the GTS.
U117687 Lost Communication with Gear Shift Control Module "A" (Powertrain Bus) Missing Message Communication stop occurs between the EV control ECU and shift control ECU continuously for approximately 1 second or more. All conditions are met:
·

1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the EV control ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC is stored until it is cleared using the GTS.


b.

Shift Control ECU / GTS Display "EV"

HINT:
·

DTC communication uses the CAN communication system.

·

When the shift control ECU detects a malfunction, the DTC is stored in the EV control ECU.



Powertrain > EV > Trouble Codes
50001 397
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010387* Lost Communication with Gear Shift Control Module "A" (Hybrid/EV Battery Local Bus) Missing Message Communication stop occurs between the EV control ECU and shift control ECU continuously for 1 second or more. All conditions are met:
·

1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the shift control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. MIL (Check engine warning light) illuminates. - DTC is stored until it is cleared using the GTS.
U014000 Lost Communication with Cruise Control Module (Sub) Missing Message Communication stop occurs between the shift control ECU and main body ECU (multiplex network body ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the shift control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U029300 Lost Communication with Hybrid/EV Powertrain Control Module from Gear Shift Control Module "A" Either of the following conditions is met:
·

Communication stop occurs between the shift control ECU and EV control ECU continuously for 1 second or more.

·

Communication stop occurs between the shift control ECU and EV control ECU continuously for approximately 11 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the shift control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 14 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U110700 Lost Communication with Power Management Module (Gear Shift Control Module "A") Communication stop occurs between the shift control ECU and certification ECU (smart key ECU assembly) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the shift control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U111087 Lost Communication with Clearance Sonar Module Missing Message Communication stop occurs between the shift control ECU and clearance warning ECU assembly continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the shift control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U117000 Lost Communication with Brake System Control Module (Gear Shift Control Module "A") Communication stop occurs between the shift control ECU and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the shift control ECU is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


c.

Battery ECU Assembly / GTS Display "EV Battery"

HINT:
·

DTC communication uses the CAN communication system.



Powertrain > EV Battery > Trouble Codes
50001 398
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the battery ECU assembly and EV control ECU continuously for 1 second or more. All conditions are met:
·

1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the battery ECU assembly is 9.6 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. Master warning light illuminates. - Up to 3 trips are stored after the system returns to normal
U115087* Lost Communication with Hybrid Powertrain Control Module (Hybrid/EV Battery Local Bus) Missing Message Communication stop occurs between the battery ECU assembly and EV control ECU continuously for 1 second or more. All conditions are met:
·

1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the battery ECU assembly is 9.6 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. Master warning light illuminates. - Up to 3 trips are stored after the system returns to normal


d.

Brake Actuator Assembly (No. 2 Skid Control ECU) / GTS Display "Brake/EPB"

HINT:

DTC communication uses the CAN communication system.


Chassis > Brake/EPB > Trouble Codes
50001 435
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U011087 Lost Communication with Drive Motor Control Module "A" Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and FC converter assembly continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds.
·

Slip indicator light illuminates.

·

Brake hold indicator light blinks.

·

Brake warning light illuminates.


- DTC is stored until it is cleared using the GTS.
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and airbag ECU assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold indicator light blinks.

·

Brake warning light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and steering sensor continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds.
·

Slip indicator light illuminates.

·

Brake hold indicator light blinks.


- DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and main body ECU (multiplex network body ECU) continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. MIL (Check engine warning light) illuminates. - DTC is stored until it is cleared using the GTS.
U015187 Lost Communication with Restraints Control Module Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and airbag ECU assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U025E87 Lost Communication with Electronic Brake Booster Control Module "A" Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and brake booster with master cylinder assembly (No. 1 skid control ECU) continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. Brake warning light illuminates. - DTC is stored until it is cleared using the GTS.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and EV control ECU continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold indicator light blinks.

·

Brake warning light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U110787 Lost Communication with Power Management Module Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and certification ECU (smart key ECU assembly) continuously for 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds. Brake warning light illuminates. - DTC is stored until it is cleared using the GTS.
U115087 Lost Communication with Hybrid Powertrain Control Module (ch2) Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and EV control ECU continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds.
·

ABS warning light illuminates.

·

Slip indicator light illuminates.

·

Brake hold indicator light blinks.

·

Brake warning light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U115987 Lost Communication with Electronic Brake Booster Control Module "A" (ch3) Missing Message Communication stop occurs between the brake actuator assembly (No. 2 skid control ECU) and brake booster with master cylinder assembly (No. 1 skid control ECU) continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake actuator assembly (No. 2 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. Brake warning light illuminates. - DTC is stored until it is cleared using the GTS.


e.

Brake Booster with Master Cylinder Assembly (No. 1 Skid Control ECU) / GTS Display "Brake Booster"

HINT:

DTC communication uses the CAN communication system.


Chassis > Brake Booster > Trouble Codes
50001 466
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U011000 Lost Communication with Drive Motor Control Module "A" Communication stop occurs between the brake booster with master cylinder assembly (No. 1 skid control ECU) and FC converter assembly continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake booster with master cylinder assembly (No. 1 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. Brake warning light illuminates. - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module "A" Missing Message Communication stop occurs between the brake booster with master cylinder assembly (No. 1 skid control ECU) and brake actuator assembly (No. 2 skid control ECU) continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake booster with master cylinder assembly (No. 1 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. Brake warning light illuminates. - DTC is stored until it is cleared using the GTS.
U029300 Lost Communication with Hybrid/EV Powertrain Control Module Communication stop occurs between the brake booster with master cylinder assembly (No. 1 skid control ECU) and EV control ECU continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake booster with master cylinder assembly (No. 1 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. Brake warning light illuminates. - DTC is stored until it is cleared using the GTS.
U110600 Lost Communication with Electric Parking Brake Module Communication stop occurs between the brake booster with master cylinder assembly (No. 1 skid control ECU) and brake actuator assembly (No. 2 skid control ECU) continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake booster with master cylinder assembly (No. 1 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. - - DTC is stored until it is cleared using the GTS.
U115000 Lost Communication with Hybrid Powertrain Control Module (ch2) Communication stop occurs between the brake booster with master cylinder assembly (No. 1 skid control ECU) and EV control ECU continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake booster with master cylinder assembly (No. 1 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. Brake warning light illuminates. - DTC is stored until it is cleared using the GTS.
U117D87 Lost Communication with Brake System Control Module (ch4) Missing Message Communication stop occurs between the brake booster with master cylinder assembly (No. 1 skid control ECU) and brake actuator assembly (No. 2 skid control ECU) continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the brake booster with master cylinder assembly (No. 1 skid control ECU) is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. Brake warning light illuminates. - DTC is stored until it is cleared using the GTS.


f.

Rack and Pinion Power Steering Gear Assembly / GTS Display "EMPS"

HINT:

DTC communication uses the CAN communication system.


Chassis > EMPS > Trouble Codes
50001 405
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U012900 Lost Communication with Brake System Control Module (System 2) Missing Message Communication stop occurs between the rack and pinion power steering gear assembly and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the rack and pinion power steering gear assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. EPS warning light illuminates. - DTC remains stored only while malfunction is occurring.
U012987 Lost Communication With Brake System Control Module Missing Message Communication stop occurs between the rack and pinion power steering gear assembly and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the rack and pinion power steering gear assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. EPS warning light illuminates. - DTC remains stored only while malfunction is occurring.
U023A00 Lost Communication with Image Processing Module "A" (System 2) Missing Message Communication stop occurs between the rack and pinion power steering gear assembly and forward recognition camera continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the rack and pinion power steering gear assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC remains stored only while malfunction is occurring.
U023A87 Lost Communication with Image Processing Module "A" Missing Message Communication stop occurs between the rack and pinion power steering gear assembly and forward recognition camera continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the rack and pinion power steering gear assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC remains stored only while malfunction is occurring.
U029300 Lost Communication With Hybrid/EV Powertrain Control Module (System 2) Communication stop occurs between the rack and pinion power steering gear assembly and EV control ECU continuously for approximately 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the rack and pinion power steering gear assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds. - - DTC remains stored only while malfunction is occurring.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module (Missing Message) Communication stop occurs between the rack and pinion power steering gear assembly and EV control ECU continuously for 5 minutes or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the rack and pinion power steering gear assembly is 9 V or higher.

·

The vehicle speed is 20 km/h (12 mph) or more.


Drive the vehicle for approximately 5 minutes or more at a speed of 20 km/h (12 mph) or more. - - DTC remains stored only while malfunction is occurring.


g.

EV Control ECU / GTS Display "Radar Cruise1"

HINT:

DTC communication uses the CAN communication system.


Powertrain > Radar Cruise1 > Trouble Codes
50001 399
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U117008 Lost Communication with Brake System Control Module (ch2) Bus Signal / Missing Message Communication stop occurs between the EV control ECU and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 1 second or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The dynamic radar cruise control system is in operation.


Turn the dynamic radar cruise control system on and wait for 4 seconds or more - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


h.

Forward Recognition Camera / GTS Display "Radar Cruise2"

HINT:
·

DTC communication uses the CAN communication system.



Powertrain > Radar Cruise2 > Trouble Codes
50001 426
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag ECU assembly continuously for approximately 1 second or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 4 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor continuously for approximately 1 second or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 4 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 5 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message The forward recognition camera does not receive data from the combination meter assembly for approximately 5 seconds or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 8 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023587* Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message The forward recognition camera does not receive data from the millimeter wave radar sensor assembly for approximately 7 seconds or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 10 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the forward recognition camera and EV control ECU continuously for approximately 1 second or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 4 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030051* Internal Control Module Software Incompatibility Not Programmed The control system information sent from the EV control ECU remains undefined by the forward recognition camera for 3 seconds or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 6 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030057* Internal Control Module Software Incompatibility Invalid / Incompatible Software Component The vehicle information sent from the EV control ECU does not match that stored in the forward recognition camera for 1 second or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 4 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U031851* Software Incompatibility with Brake System Control Module Not Programmed The vehicle information sent from brake actuator assembly (No. 2 skid control ECU) remains undefined by the forward recognition camera for 3 seconds or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 6 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U031857* Software Incompatibility with Brake System Control Module Invalid / Incompatible Software Component The vehicle information sent from the brake actuator assembly (No. 2 skid control ECU) does not match that stored in the forward recognition camera for 2 seconds or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 5 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U032251* Software Incompatibility with Body Control Module Not Programmed The vehicle information sent from the main body ECU (multiplex network body ECU) remains undefined by the forward recognition camera for 6 seconds or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 9 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U032257* Software Incompatibility with Body Control Module Invalid / Incompatible Software Component The vehicle information sent from the main body ECU (multiplex network body ECU) does not match that stored in the forward recognition camera for 4 seconds or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 7 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U059481* Invalid Data Received from Hybrid/EV Powertrain Control Module Invalid Serial Data Received The EV control ECU does not receive data from the forward recognition camera for approximately 2 seconds or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 5 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U110687 Lost Communication with Electric Parking Brake Module Missing Message The forward recognition camera does not receive data from the brake actuator assembly (No. 2 skid control ECU) for approximately 2 seconds or more. All conditions are met:
·

The dynamic radar cruise control system is in operation.

·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


With the dynamic radar cruise operating, drive the vehicle for approximately 7 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


i.

Forward Recognition Camera / GTS Display "Pre-Collision System"

HINT:
·

DTC communication uses the CAN communication system.



Body Electrical > Pre-Collision System > Trouble Codes
50001 432
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag ECU assembly continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

Vehicle speed is 5 km/h (3 mph) or more.


Drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 5 seconds or more. PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U013187 Lost Communication with Power Steering Control Module Missing Message Communication stop occurs between the forward recognition camera and rack and pinion power steering gear assembly continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023587* Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message The forward recognition camera does not receive data from the millimeter wave radar sensor assembly for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023A87* Lost Communication with Image Processing Module "A" Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

2 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the forward recognition camera and EV control ECU continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.

·

Vehicle speed is 5 km/h (3 mph) or more.


Drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 7 seconds or more. PCS warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030051* Internal Control Module Software Incompatibility Not Programmed The vehicle information sent from the EV control ECU remains undefined by the forward recognition camera for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. PCS warning light blinks. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030057* Internal Control Module Software Incompatibility Invalid / Incompatible Software Component The vehicle information sent from the EV control ECU does not match that stored in the forward recognition camera for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. PCS warning light blinks. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U041881* Invalid Data Received from Brake System Control Module Invalid Serial Data Received The forward recognition camera receives an abnormal brake system control signal from the brake actuator assembly (No. 2 skid control ECU) for 1 second or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. PCS warning light blinks. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


j.

Forward Recognition Camera / GTS Display "Front Recognition Camera"

HINT:
·

DTC communication uses the CAN communication system.



Chassis > Front Recognition Camera > Trouble Codes
50001 430
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag ECU assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.

·

The vehicle speed is 1 km/h (1 mph) or more.


Drive the vehicle for 8 seconds or more at a speed of 1 km/h (1 mph) or more. - - DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor continuously for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The vehicle speed is 1 km/h (1 mph) or more.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (No. 2 skid control ECU) assembly continuously for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the forward recognition camera and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the forward recognition camera and EV control ECU continuously for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Drive the vehicle for approximately 8 seconds or more at a speed of 1 km/h (1 mph) or more. - - DTC is stored until it is cleared using the GTS.
U030051* Internal Control Module Software Incompatibility Not Programmed The control system information sent from the EV control ECU remains undefined by the forward recognition camera for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U030057* Internal Control Module Software Incompatibility Invalid / Incompatible Software Component The control system information sent from the EV control ECU does not match that stored in the forward recognition camera for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U032251* Software Incompatibility with Body Control Module Not Programmed The vehicle information sent from the main body ECU (multiplex network body ECU) remains undefined by the forward recognition camera for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U032257* Software Incompatibility with Body Control Module Invalid / Incompatible Software Component The vehicle information sent from the main body ECU (multiplex network body ECU) does not match that stored in the forward recognition camera for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.


k.

Forward Recognition Camera / GTS Display "Front Recognition Camera (Front Lighting Control)"

HINT:
·

DTC communication uses the CAN communication system.



Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag ECU assembly continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more have elapsed with the IG voltage at 10 V or higher from the time the ignition switch is turned ON.

·

The vehicle speed is 1 km/h (1 mph) or more.


The vehicle has been driven for 7 seconds or more at a speed of 1 km/h (1 mph) or more and with the IG voltage at 10 V or higher. Automatic high beam indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (No. 2 skid control ECU) continuously for 5 seconds or more. 2 seconds or more have elapsed with the IG voltage at 10 V or higher from the time the ignition switch is turned ON. Wait at least 7 seconds with the IG voltage at 10 V or higher. Automatic high beam indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the forward recognition camera and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. 2 seconds or more have elapsed with the IG voltage at 10 V or higher from the time the ignition switch is turned ON. Wait at least 7 seconds with the IG voltage at 10 V or higher. Automatic high beam indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U018287* Lost Communication with Lighting Control Module Front Missing Message Communication stop occurs between the forward recognition camera and headlight ECU sub-assembly LH continuously for 5 seconds or more. 2 seconds or more have elapsed with the IG voltage at 10 V or higher from the time the ignition switch is turned ON. Wait at least 7 seconds with the IG voltage at 10 V or higher. - - DTC is stored until it is cleared using the GTS.
U023587* Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message Communication stop occurs between the forward recognition camera and millimeter wave radar sensor assembly continuously for 5 seconds or more. 2 seconds or more have elapsed with the IG voltage at 10 V or higher from the time the ignition switch is turned ON. Wait at least 7 seconds with the IG voltage at 10 V or higher. Automatic high beam indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the forward recognition camera and EV control ECU continuously for 5 seconds or more. All conditions are met:
·

2 seconds or more have elapsed with the IG voltage at 10 V or higher from the time the ignition switch is turned ON.

·

The vehicle speed is 1 km/h (1 mph) or more.


The vehicle has been driven for 7 seconds or more at a speed of 1 km/h (1 mph) or more and with the IG voltage at 10 V or higher. Automatic high beam indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


l.

Forward Recognition Camera / GTS Display "Lane Control"

HINT:
·

DTC communication uses the CAN communication system.



Chassis > Lane Control > Trouble Codes
50001 418
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message The forward recognition camera does not receive data from the airbag ECU assembly sensor for approximately 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The LTA main switch is on.

·

Vehicle speed is 5 km/h (3 mph) or more.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Drive the vehicle for 8 seconds or more at a speed of 5 km/h (3 mph) or more. LTA indicator light (umber) illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the forward recognition camera and steering sensor continuously for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The LTA main switch is on.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. LTA indicator light (umber) illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (No. 2 skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The LTA main switch is on.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. LTA indicator light (umber) illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U013187 Lost Communication with Power Steering Control Module Missing Message Communication stop occurs between the forward recognition camera and rack and pinion power steering gear assembly continuously for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The LTA main switch is on.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. LTA indicator light (umber) illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the forward recognition camera and combination meter assembly continuously for 50 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The LTA main switch is on.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least 53 seconds. LTA indicator light (umber) illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U023587* Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message Communication stop occurs between the forward recognition camera and millimeter wave radar sensor assembly continuously for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The LTA main switch is on.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. LTA indicator light (umber) illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the forward recognition camera and EV control ECU continuously for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The lane control system is in operation.

·

The vehicle speed is 5 km/h (3 mph) or more.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Drive the vehicle for 8 seconds or more at a speed of 5 km/h (3 mph) or more. LTA indicator light (umber) illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030051* Internal Control Module Software Incompatibility Not Programmed The vehicle information sent from the EV control ECU remains undefined by the forward recognition camera. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The LTA/LDA main switch is on.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait for at least approximately 3 seconds. LTA indicator light (umber) illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030057* Internal Control Module Software Incompatibility Invalid / Incompatible Software Component The vehicle information sent from the EV control ECU does not match that stored in the forward recognition camera for 5 seconds or more. All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The LTA/LDA main switch is on.

·

The power source voltage of the forward recognition camera is 10 V or higher.


Turn the ignition switch to ON and wait for at least approximately 8 seconds. LTA indicator light (umber) illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


m.

Forward Recognition Camera / GTS Display "Road Sign Assist"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Road Sign Assist > Trouble Codes
50001 431
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Communication stop occurs between the forward recognition camera and airbag ECU assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Drive the vehicle for 8 seconds or more at a speed of 8 km/h (5 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the forward recognition camera and brake actuator assembly (No. 2 skid control ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the forward recognition camera and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U015587 Lost Communication With Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the forward recognition camera and combination meter assembly continuously for 50 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 53 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the forward recognition camera and EV control ECU continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The power source voltage of the forward recognition camera is 9.5 V or higher.


Drive the vehicle for 8 seconds or more at a speed of 8 km/h (5 mph) or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


n.

Millimeter Wave Radar Sensor Assembly / GTS Display "Front Radar Sensor"

HINT:
·

DTC communication uses the CAN communication system.



DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010487* Lost Communication with Cruise Control Module Missing Message The millimeter wave radar sensor assembly does not receive data from the forward recognition camera for approximately 1 second or more. All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the millimeter wave radar sensor assembly is 8 V or higher.


Turn the ignition switch to ON and wait at least approximately 2 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U030557* Software Incompatibility with Cruise Control Module Invalid / Incompatible Software Component The control system information sent from the forward recognition camera does not match that stored in the millimeter wave radar sensor assembly for 7 seconds or more. All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the millimeter wave radar sensor assembly is 8 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


o.

Blind Spot Monitor Sensor RH (B) / GTS Display "Blind Spot Monitor Master"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0125 Lost Communication with Yaw Rate Sensor Module Communication stop occurs between the blind spot monitor sensor RH (B) and airbag ECU assembly continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the blind spot monitor sensor RH (B) is 10 V or higher.

·

The vehicle speed is 7 km/h (4 mph) or more.


Drive the vehicle at a speed of 7 km/h (4 mph) or more for approximately 7 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Either of the following conditions is met:
·

Communication stop occurs between the blind spot monitor sensor RH (B) and steering sensor continuously for approximately 11 seconds or more.

·

Communication stop occurs between the blind spot monitor sensor RH (B) and steering sensor continuously for approximately 4 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the blind spot monitor sensor RH (B) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 14 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the blind spot monitor sensor RH (B) and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the blind spot monitor sensor RH (B) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the blind spot monitor sensor RH (B) and main body ECU (multiplex network body ECU) continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the blind spot monitor sensor RH (B) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 14 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U0293 Lost Communication with HV/EV ECU Communication stop occurs between the blind spot monitor sensor RH (B) and EV control ECU continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the blind spot monitor sensor RH (B) is 10 V or higher.

·

The vehicle speed is 5 km/h (3 mph) or more.


Drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 14 seconds or more. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


p.

Airbag ECU Assembly / GTS Display "SRS Airbag"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > SRS Airbag > Trouble Codes
50001 444
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Either of the following conditions is met:
·

Communication stop occurs between the airbag ECU assembly and steering sensor continuously for 2 seconds or more.

·

Communication stop occurs between the airbag ECU assembly and steering sensor continuously for approximately 6 seconds or more.


3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 9 seconds. Pedestrian protection system warning light illuminates. - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module "A" Missing Message Either of the following conditions is met:
·

Communication stop occurs between the airbag ECU assembly and brake actuator assembly (No. 2 skid control ECU) continuously for 2 seconds or more.

·

Communication stop occurs between the airbag ECU assembly and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 5 seconds or more.


3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 8 seconds. Pedestrian protection system warning light illuminates. - DTC is stored until it is cleared using the GTS.
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message Communication stop occurs between the airbag ECU assembly and millimeter wave radar sensor assembly continuously for approximately 10 seconds or more. 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 13 seconds.
·

SRS warning light illuminates.

·

Pedestrian protection system warning light illuminates.


- DTC is stored until it is cleared using the GTS.
U023A87 Lost Communication with Image Processing Module "A" Missing Message Communication stop occurs between the airbag ECU assembly and forward recognition camera continuously for approximately 10 seconds or more. 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 13 seconds.
·

SRS warning light illuminates.

·

Pedestrian protection system warning light illuminates.


- DTC is stored until it is cleared using the GTS.


q.

Certification ECU (Smart Key ECU Assembly) / GTS Display "Entry&Start"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Entry&Start > Trouble Codes
50001 125
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0142 Lost Communication with Body Control Module "B" Communication stop occurs between the certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

Approximately 10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

Approximately 10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0293 Lost Communication With Hybrid/EV Vehicle Control System Communication stop occurs between the certification ECU (smart key ECU assembly) and EV control ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


r.

Certification ECU (Smart Key ECU Assembly) / GTS Display "Power Source Control"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Power Source Control > Trouble Codes
50001 223
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 ECM/EV Communication Communication stop occurs between the certification ECU (smart key ECU assembly) and EV control ECU continuously for approximately 4 seconds or more. All conditions are met:
·

Ignition switch is ON.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. - - DTC is stored until it is cleared using the GTS.
U0103 Lost Communication with Gear Shift Module "A" Communication stop occurs between the certification ECU (smart key ECU assembly) and shift control ECU continuously for 5 seconds or more. All conditions are met:
·

Ignition switch is ON.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - - DTC is stored until it is cleared using the GTS.
U0129 Vehicle Speed Signal Communication Communication stop occurs between the certification ECU (smart key ECU assembly) and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

Ignition switch is ON.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. - - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) continuously for 3 seconds or more. All conditions are met:
·

Ignition switch is ON.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 3 seconds. - - DTC is stored until it is cleared using the GTS.
U0164 Lost Communication with HVAC Control Module Communication stop occurs between the certification ECU (smart key ECU assembly) and air conditioning amplifier assembly continuously for 5 seconds or more. Power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off). Turn the ignition switch to ON and wait at least 5 seconds. - - DTC is stored until it is cleared using the GTS.
U0293 HV/EV ECU Communication Communication stop occurs between the certification ECU (smart key ECU assembly) and EV control ECU continuously for approximately 4 seconds or more. All conditions are met:
·

Ignition switch is ON.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. - - DTC is stored until it is cleared using the GTS.


s.

Combination Meter Assembly / GTS Display "Combination Meter"

HINT:
·

DTC communication uses the CAN communication system.

·

*1: w/ Navigation System

·

*2: w/o Navigation System



Body Electrical > Combination Meter > Trouble Codes
50001 409
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010387 Lost Communication with Gear Shift Control Module "A" Missing Message Communication stop occurs between the combination meter assembly and shift control ECU continuously for approximately 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the combination meter assembly and steering sensor continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U012787 Lost Communication with Tire Pressure Monitor Module Missing Message Communication stop occurs between the combination meter assembly and tire pressure warning ECU and receiver continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Either of the following conditions is met:
·

Communication stop occurs between the combination meter assembly and brake actuator assembly (No. 2 skid control ECU) continuously for 1 second or more.

·

Communication stop occurs between the combination meter assembly and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 4 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds.
·

ABS warning light illuminates.

·

VSC OFF indicator light illuminates.

·

Brake warning light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U013187 Lost Communication with Power Steering Control Module Missing Message Communication stop occurs between the combination meter assembly and rack and pinion power steering gear assembly continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. EPS warning light illuminates. - DTC is stored until it is cleared using the GTS.
U014287 Lost Communication with Body Control Module "B" Missing Message Communication stop occurs between the combination meter assembly and main body ECU (multiplex network body ECU) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U015187 Lost Communication with Restraints Control Module Missing Message Communication stop occurs between the combination meter assembly and airbag ECU assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. SRS warning light illuminates. - DTC is stored until it is cleared using the GTS.
U016387 Lost Communication with Navigation Control Module Missing Message
·

Communication stop occurs between the combination meter assembly and radio receiver assembly continuously for 5 seconds or more.*1

·

Communication stop occurs between the combination meter assembly and radio and display receiver assembly continuously for 5 seconds or more.*2


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U016487 Lost Communication with HVAC Control Module Missing Message Communication stop occurs between the combination meter assembly and air conditioning amplifier assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U018287 Lost Communication with Lighting Control Module Front Missing Message Communication stop occurs between the combination meter assembly and headlight ECU sub-assembly LH continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U023387 Lost Communication with Side Obstacle Detection Control Module "B" Missing Message Communication stop occurs between the combination meter assembly and blind spot monitor sensor RH (B) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U023A87 Lost Communication with Image Processing Module "A" Missing Message Communication stop occurs between the combination meter assembly and forward recognition camera continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. Lane departure alert indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the combination meter assembly and EV control ECU continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. - - DTC is stored until it is cleared using the GTS.
U032787 Software Incompatibility with Vehicle Security Control Module Missing Message Communication stop occurs between the combination meter assembly and certification ECU (smart key ECU assembly) continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U110687 Lost Communication with Electric Parking Brake Module Missing Message Communication stop occurs between the combination meter assembly and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. - - DTC is stored until it is cleared using the GTS.
U111087 Lost Communication with Clearance Sonar Module Missing Message Communication stop occurs between the combination meter assembly and clearance warning ECU assembly continuously for 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. CSR OFF indicator light illuminates. - DTC is stored until it is cleared using the GTS.
U111287 Lost Communication with Combination Switch Module Missing Message Communication stop occurs between the combination meter assembly and steering sensor continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 13 seconds. - - DTC is stored until it is cleared using the GTS.
U113387 Lost Communication with PMN Module Missing Message Communication stop occurs between the combination meter assembly and certification ECU (smart key ECU assembly) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the combination meter assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. - - DTC is stored until it is cleared using the GTS.


t.

Meter Mirror Sub-assembly / GTS Display "Head Up Display" (w/ Head Up Display System)

HINT:
·

DTC communication uses the CAN communication system.

·

*1: w/ Navigation System

·

*2: w/o Navigation System



Body Electrical > Head Up Display > Trouble Codes
50001 408
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010387 Lost Communication with Gear Shift Control Module "A" Missing Message Communication stop occurs between the meter mirror sub-assembly and shift control ECU continuously for approximately 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Communication stop occurs between the meter mirror sub-assembly and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. - - DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the meter mirror sub-assembly and main body ECU (multiplex network body ECU) continuously for approximately 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U014287 Lost Communication with Body Control Module "B" Missing Message Communication stop occurs between the meter mirror sub-assembly and main body ECU (multiplex network body ECU) continuously for approximately 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the meter mirror sub-assembly and combination meter assembly continuously for approximately 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U016387 Lost Communication with Navigation Control Module Missing Message
·

Communication stop occurs between the meter mirror sub-assembly and radio receiver assembly continuously for approximately 5 seconds or more.*1

·

Communication stop occurs between the meter mirror sub-assembly and radio and display receiver assembly continuously for approximately 5 seconds or more.*2


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U016487 Lost Communication with HVAC Control Module Missing Message Communication stop occurs between the meter mirror sub-assembly and air conditioning amplifier assembly continuously for approximately 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Missing Message Communication stop occurs between the meter mirror sub-assembly and forward recognition camera continuously for approximately 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U023A87 Lost Communication with Image Processing Module "A" Missing Message Communication stop occurs between the meter mirror sub-assembly and forward recognition camera continuously for approximately 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 8 seconds. - - DTC is stored until it is cleared using the GTS.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Either of the following conditions is met:
·

Communication stop occurs between the meter mirror sub-assembly and EV control ECU continuously for approximately 4 seconds or more.

·

Communication stop occurs between the meter mirror sub-assembly and EV control ECU continuously for approximately 5 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U110487 Lost Communication with Driving Support ECU Missing Message Communication stop occurs between the meter mirror sub-assembly and forward recognition camera continuously for approximately 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.
U111087 Lost Communication with Clearance Sonar Module Missing Message Communication stop occurs between the meter mirror sub-assembly and clearance warning ECU assembly continuously for approximately 5 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the meter mirror sub-assembly is 10.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 8 seconds. - - DTC is stored until it is cleared using the GTS.


u.

Integration Control Sub-assembly / GTS Display "D-SEAT SW" (w/ Navigation System)

HINT:
·

DTC communication uses the CAN communication system.

·

*1: w/ Navigation System

·

*2: w/o Navigation System



Body Electrical > D-SEAT SW > Trouble Codes
50001 181
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0100 Lost Communication with ECM/PCM "A" Communication stop occurs between the integration control sub-assembly and EV control ECU continuously for 10 seconds or more. All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the integration control sub-assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 11 seconds. - - DTC remains stored only while malfunction is occurring.
U0142 Mainbody ECU communication circuit Communication stop occurs between the integration control sub-assembly and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the integration control sub-assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 11 seconds. - - DTC remains stored only while malfunction is occurring.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the integration control sub-assembly and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the integration control sub-assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 11 seconds. - - DTC remains stored only while malfunction is occurring.
U0163 Lost Communication with Navigation Control Module Communication stop occurs between the meter mirror sub-assembly and radio receiver assembly continuously for approximately 5 seconds or more. All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the integration control sub-assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 11 seconds. - - DTC remains stored only while malfunction is occurring.
U0164 Lost Communication with HVAC Control Module Communication stop occurs between the integration control sub-assembly and air conditioning amplifier assembly continuously for 10 seconds or more. All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the integration control sub-assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 11 seconds. - - DTC remains stored only while malfunction is occurring.
U023B Lost Communication with Image Processing Module "B" Communication stop occurs between the integration control sub-assembly and parking assist ECU continuously for 10 seconds or more. All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the integration control sub-assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 11 seconds. - - DTC remains stored only while malfunction is occurring.
U0265 Lost Communication with Image Processing Sensor A Communication stop occurs between the integration control sub-assembly and rear television camera assembly continuously for 10 seconds or more. All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the integration control sub-assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 11 seconds. - - DTC remains stored only while malfunction is occurring.


v.

Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Air Conditioner > Trouble Codes
50001 121
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0131 Lost Communication With Power Steering Control Module Communication stop occurs between the air conditioning amplifier assembly and the rack and pinion power steering gear assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication With Body Control Module "B" Communication stop occurs between the air conditioning amplifier assembly and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication With Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the air conditioning amplifier assembly and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0293 Lost Communication With HV/EV ECU Communication stop occurs between the air conditioning amplifier assembly and EV control ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. Master warning light illuminates. - DTC is stored until it is cleared using the GTS.
U0327 Software Incompatibility with Vehicle Security Control Module Communication stop occurs between the air conditioning amplifier assembly and certification ECU (smart key ECU assembly) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1114 Lost Communication with Driver Seat Module Communication stop occurs between the air conditioning amplifier assembly and integration control sub-assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


w.

Radio Receiver Assembly / GTS Display "Navigation System" (w/ Navigation System)

HINT:
·

DTC communication uses the CAN communication system.

·

ECB*: Electronically Controlled Brake System



Body Electrical > Navigation System > Trouble Codes
50001 212
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0073 Sending Malfunction (Navigation to APGS) Either of the following conditions is met:
·

Bus off condition is detected.

·

CAN bus is not connected.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 3 seconds. - - DTC is stored until it is cleared using the GTS.
U0129 VSC(ECB*)ECU Communication Communication stop occurs between the radio receiver assembly and brake actuator assembly (No. 2 skid control ECU) at vehicle speed of 20 km/h (12 mph) or more continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.

·

The vehicle speed is 20 km/h (12 mph) or more.


Drive the vehicle for 13 seconds or more at a speed of 20 km/h (12 mph) or more. - - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module Either of the following conditions is met:
·

Communication stop occurs between the radio receiver assembly and main body ECU (multiplex network body ECU) continuously for 5 seconds or more.

·

Communication stop occurs between the radio receiver assembly and main body ECU (multiplex network body ECU) continuously for 10 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Meter ECU Communication Either of the following conditions is met:
·

Communication stop occurs between the radio receiver assembly and combination meter assembly continuously for 3 seconds or more.

·

Communication stop occurs between the radio receiver assembly and combination meter assembly continuously for 30 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 33 seconds. - - DTC is stored until it is cleared using the GTS.
U0163 Lost Communication With Navigation Control Module Communication stop occurs between the radio receiver assembly and telematics transceiver continuously for 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds. - - DTC is stored until it is cleared using the GTS.
U0164 Air Conditioner ECU Communication Communication stop occurs between the radio receiver assembly and air conditioning amplifier assembly continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC is stored until it is cleared using the GTS.
U0198 Lost Communication with Telematic Control Module Communication stop occurs between the radio receiver assembly and telematics transceiver continuously for 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds. - - DTC is stored until it is cleared using the GTS.
U023B Lost Communication with Image Processing Module "B" Communication stop occurs between the radio receiver assembly and parking assist ECU continuously for approximately 12 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 15 seconds. - - DTC is stored until it is cleared using the GTS.
U0265 Lost Communication with Image Processing Sensor A Communication stop occurs between the radio receiver assembly and rear television camera assembly continuously for approximately 12 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 15 seconds. - - DTC is stored until it is cleared using the GTS.
U0293 HV/EV ECU Communication Communication stop occurs between the radio receiver assembly and EV control ECU continuously for 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds. - - DTC is stored until it is cleared using the GTS.
Communication stop occurs between the radio receiver assembly and EV control ECU continuously for 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
Communication stop occurs between the radio receiver assembly and EV control ECU at vehicle speed of 20 km/h (12 mph) or more continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.

·

The vehicle speed is 20 km/h (12 mph) or more.


Drive the vehicle for 13 seconds or more at a speed of 20 km/h (12 mph) or more. - - DTC is stored until it is cleared using the GTS.
U1110 Clearance Sonar ECU Communication Communication stop occurs between the radio receiver assembly and clearance warning ECU assembly continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC is stored until it is cleared using the GTS.


x.

Radio and Display Receiver Assembly / GTS Display (w/o Navigation System)

HINT:
·

DTC communication uses the CAN communication system.

·

ECB*: Electronically Controlled Brake System



Body Electrical > Navigation System > Trouble Codes
50001 212
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0073 Sending Malfunction (Navigation to APGS) Either of the following conditions is met:
·

Bus off condition is detected.

·

CAN bus is not connected.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 3 seconds. - - DTC is stored until it is cleared using the GTS.
U0129 VSC(ECB*)ECU Communication Communication stop occurs between the radio and display receiver assembly and brake actuator assembly (No. 2 skid control ECU) at vehicle speed of 20 km/h (12 mph) or more continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.

·

The vehicle speed is 20 km/h (12 mph) or more.


Drive the vehicle for 13 seconds or more at a speed of 20 km/h (12 mph) or more. - - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module Either of the following conditions is met:
·

Communication stop occurs between the radio and display receiver assembly and main body ECU (multiplex network body ECU) continuously for 5 seconds or more.

·

Communication stop occurs between the radio and display receiver assembly and main body ECU (multiplex network body ECU) continuously for 10 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Meter ECU Communication Either of the following conditions is met:
·

Communication stop occurs between the radio and display receiver assembly and combination meter assembly continuously for 3 seconds or more.

·

Communication stop occurs between the radio and display receiver assembly and combination meter assembly continuously for 30 seconds or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 33 seconds. - - DTC is stored until it is cleared using the GTS.
U0163 Lost Communication With Navigation Control Module Communication stop occurs between the radio and display receiver assembly and telematics transceiver continuously for 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds. - - DTC is stored until it is cleared using the GTS.
U0164 Air Conditioner ECU Communication Communication stop occurs between the radio and display receiver assembly and air conditioning amplifier assembly continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC is stored until it is cleared using the GTS.
U0198 Lost Communication with Telematic Control Module Communication stop occurs between the radio and display receiver assembly and telematics transceiver continuously for 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds. - - DTC is stored until it is cleared using the GTS.
U023B Lost Communication with Image Processing Module "B" Communication stop occurs between the radio and display receiver assembly and parking assist ECU continuously for approximately 12 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 15 seconds. - - DTC is stored until it is cleared using the GTS.
U0265 Lost Communication with Image Processing Sensor A Communication stop occurs between the radio and display receiver assembly and rear television camera assembly continuously for approximately 12 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 15 seconds. - - DTC is stored until it is cleared using the GTS.
U0293 HV/EV ECU Communication Communication stop occurs between the radio and display receiver assembly and EV control ECU continuously for 3 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds. - - DTC is stored until it is cleared using the GTS.
Communication stop occurs between the radio and display receiver assembly and EV control ECU continuously for 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
Communication stop occurs between the radio and display receiver assembly and EV control ECU at vehicle speed of 20 km/h (12 mph) or more continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.

·

The vehicle speed is 20 km/h (12 mph) or more.


Drive the vehicle for 13 seconds or more at a speed of 20 km/h (12 mph) or more. - - DTC is stored until it is cleared using the GTS.
U1110 Clearance Sonar ECU Communication Communication stop occurs between the radio and display receiver assembly and clearance warning ECU assembly continuously for 10 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the radio and display receiver assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - - DTC is stored until it is cleared using the GTS.


y.

Telematics Transceiver / GTS Display "Telematics"

HINT:
·

DTC communication uses the CAN communication system.

·

*1: w/ Navigation System

·

*2: w/o Navigation System



Body Electrical > Telematics > Trouble Codes
50001 459
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the telematics transceiver and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the telematics transceiver is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC remains stored only while malfunction is occurring.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the telematics transceiver and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the telematics transceiver is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC remains stored only while malfunction is occurring.
U016387 Lost Communication with Navigation Control Module Missing Message
·

Communication stop occurs between the telematics transceiver and radio receiver assembly continuously for 10 seconds or more.*1

·

Communication stop occurs between the telematics transceiver and radio and display receiver assembly continuously for 10 seconds or more.*2


All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the telematics transceiver is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC remains stored only while malfunction is occurring.


z.

Stereo Component Equalizer Assembly / GTS Display "ASC" (w/ ASC System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > ASC > Trouble Codes
50001 365
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0125 Lost Communication with Multi-axis Acceleration Sensor Module "A" Communication stop occurs between the stereo component equalizer assembly and airbag ECU assembly continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the stereo component equalizer assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the stereo component equalizer assembly and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the stereo component equalizer assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 5 seconds. - - DTC is stored until it is cleared using the GTS.
U0142 Lost Communication With Body Control Module "B" Communication stop occurs between the stereo component equalizer assembly and main body ECU (multiplex network body ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the stereo component equalizer assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. - - DTC is stored until it is cleared using the GTS.
U0293 Lost Communication With Hybrid Powertrain Control Module Either of the following conditions is met:
·

Communication stop occurs between the stereo component equalizer assembly and EV control ECU continuously for approximately 2 seconds second or more.

·

Communication stop occurs between the stereo component equalizer assembly and EV control ECU continuously for approximately 6 seconds second or more.


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the stereo component equalizer assembly is 9.5 V or higher.


Turn the ignition switch to ON and wait at least approximately 9 seconds. - - DTC is stored until it is cleared using the GTS.


aa.

Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"

HINT:
·

DTC communication uses the CAN communication system.

·

EPB*: Electric Parking Brake



Body Electrical > Main Body > Trouble Codes
50001 123
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0101 Lost Communication with TCM Communication stop occurs between the main body ECU (multiplex network body ECU) and EV control ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0120 Lost Communication With Starter / Generator Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and certification ECU (smart key ECU assembly) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the main body ECU (multiplex network body ECU) and steering sensor continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0151 Lost Communication with Restraints Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and airbag ECU assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and combination meter assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0182 Lost Communication with AFS Communication stop occurs between the main body ECU (multiplex network body ECU) and headlight ECU sub-assembly LH continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0199 Lost Communication with "Door Control Module A" Communication stop occurs between the main body ECU (multiplex network body ECU) and front multiplex network door ECU RH continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0200 Lost Communication with "Door Control Module B" Communication stop occurs between the main body ECU (multiplex network body ECU) and front multiplex network door ECU LH continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0208 Lost Communication with "Seat Control Module A" Communication stop occurs between the main body ECU (multiplex network body ECU) and position control ECU assembly continuously for 10 seconds or more. All conditions are met:
·

Approximately 10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 20 seconds. - - DTC is stored until it is cleared using the GTS.
U023A Lost Communication With Image Processing Module "A" Communication stop occurs between the main body ECU (multiplex network body ECU) and forward recognition camera continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0293 Lost Communication with Hybrid/EV Powertrain Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and EV control ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0327 Software Incompatibility with Vehicle Security Control Module Communication stop occurs between the main body ECU (multiplex network body ECU) and certification ECU (smart key ECU assembly) continuously for approximately 10 seconds or more. All conditions are met:
·

Approximately 10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1106 Lost Communication with Electric Parking Brake Module Communication stop occurs between the main body ECU (multiplex network body ECU) and brake actuator assembly (No. 2 skid control ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 20 seconds. - - DTC is stored until it is cleared using the GTS.
U1114 Lost Communication with Main Switch Module Communication stop occurs between the main body ECU (multiplex network body ECU) and integration control sub-assembly continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - 10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).
U1115 Lost Communication with Tilt & Telescopic Module Communication stop occurs between the main body ECU (multiplex network body ECU) and the multiplex tilt and telescopic ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or ON changes between ON and off).

·

The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


ab.

Multiplex Tilt and Telescopic ECU / GTS Display "Tilt & Telescopic"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Tilt&Telescopic > Trouble Codes
50001 406
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U014287 Lost Communication with Body Control Module "B" Missing Message Communication stop occurs between the multiplex tilt and telescopic ECU and main body ECU (multiplex network body ECU) continuously for approximately 4 seconds or more. The power source voltage of the multiplex tilt and telescopic ECU is 9 V or higher. Wait at least approximately 4 seconds with the power source voltage of the multiplex tilt and telescopic ECU at 9 V or higher. - - DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Communication stop occurs between the multiplex tilt and telescopic ECU and combination meter assembly continuously for approximately 10 seconds or more. The power source voltage of the multiplex tilt and telescopic ECU is 9 V or higher. Wait at least 10 seconds with the power source voltage of the multiplex tilt and telescopic ECU at 9 V or higher. - - DTC is stored until it is cleared using the GTS.
U020887 Lost Communication with "Seat Control Module A" Missing Message Communication stop occurs between the multiplex tilt and telescopic ECU and position control ECU assembly continuously for approximately 10 seconds or more. The power source voltage of the multiplex tilt and telescopic ECU is 9 V or higher. Wait at least 10 seconds with the power source voltage of the multiplex tilt and telescopic ECU at 9 V or higher. - - DTC is stored until it is cleared using the GTS.


ac.

Front Multiplex Network Door ECU RH / GTS Display "Front Right Door" (w/ Rerese Shift-linked Mirror)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Front Right Door > Trouble Codes
50001 224
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0142 Lost Communication With Body Control Module "B" Communication stop occurs between the front multiplex network door ECU RH and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or IG changes between ON and off).

·

The power source voltage of the front multiplex network door ECU RH is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


ad.

Front Multiplex Network Door ECU LH / GTS Display "Front Left Door" (w/ Rerese Shift-linked Mirror)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Front Left Door > Trouble Codes
50001 225
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0142 Lost Communication With Body Control Module "B" Communication stop occurs between the front multiplex network door ECU LH and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or IG changes between ON and off).

·

The power source voltage of the front multiplex network door ECU LH is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


ae.

Rear Multiplex Network Door ECU RH / GTS Display "Rear Right Door" (w/ Double Locking System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Rear Right Door > Trouble Codes
50001 161
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0142 Lost Communication With Body Control Module "B" Communication stop occurs between the rear multiplex network door ECU RH and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or IG changes between ON and off).

·

The power source voltage of the rear multiplex network door ECU RH is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


af.

Rear Multiplex Network Door ECU LH / GTS Display "Rear Left Door" (w/ Double Locking System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Rear Left Door > Trouble Codes
50001 160
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0142 Lost Communication With Body Control Module "B" Communication stop occurs between the rear multiplex network door ECU LH and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to ON, ACC changes between ON and off, or IG changes between ON and off).

·

The power source voltage of the rear multiplex network door ECU LH is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


ag.

Clearance Warning ECU Assembly / GTS Display "Clearance Warning"

HINT:
·

DTC communication uses the CAN communication system.



Body Electrical > Clearance Warning > Trouble Codes
50001 438
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U010387 Lost Communication with Gear Shift Control Module "A" Missing Message Communication stop occurs between the clearance warning ECU assembly and shift control ECU continuously for approximately 1 second or more. All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 2 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012687 Lost Communication With Steering Angle Sensor Module Missing Message Either of the following conditions is met:
·

Communication stop occurs between the clearance warning ECU assembly and steering sensor continuously for approximately 1 second or more.

·

Communication stop occurs between the clearance warning ECU assembly and steering sensor continuously for approximately 6 seconds or more.


All conditions are met:
·

Approximately 6 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 12 seconds.
·

CSR OFF indicator light illuminates.

·

Parking brake warning light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module Missing Message Either of the following conditions is met:
·

Communication stop occurs between the clearance warning ECU assembly and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 1 second or more.

·

Communication stop occurs between the clearance warning ECU assembly and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 3 seconds or more.


All conditions are met:
·

Approximately 3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 6 seconds.
·

CSR OFF indicator light illuminates.

·

Parking brake warning light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U013187 Lost Communication with Power Steering Control Module Missing Message Communication stop occurs between the clearance warning ECU assembly and rack and pinion power steering gear assembly continuously for approximately 1 second or more. All conditions are met:
·

Approximately 1 second or more elapses after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 2 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Either of the following conditions is met:
·

Communication stop occurs between the clearance warning ECU assembly and main body ECU (multiplex network body ECU) continuously for approximately 3 seconds or more.

·

Communication stop occurs between the clearance warning ECU assembly and main body ECU (multiplex network body ECU) continuously for approximately 5 seconds or more.


All conditions are met:
·

Approximately 5 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 10 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U015587 Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message Either of the following conditions is met:
·

Communication stop occurs between the clearance warning ECU assembly and combination meter assembly continuously for approximately 3 seconds or more.

·

Communication stop occurs between the clearance warning ECU assembly and combination meter assembly continuously for approximately 5 seconds or more.


All conditions are met:
·

Approximately 5 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 10 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U016487 Lost Communication with HVAC Control Module Missing Message Communication stop occurs between the clearance warning ECU assembly and air conditioning amplifier assembly continuously for approximately 5 seconds or more. All conditions are met:
·

Approximately 5 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 10 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U026587 Lost Communication with Image Processing Sensor A Missing Message Communication stop occurs between the clearance warning ECU assembly and rear television camera assembly continuously for approximately 2 seconds or more. All conditions are met:
·

Approximately 5 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 7 seconds. Parking brake warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the clearance warning ECU assembly and EV control ECU continuously for approximately 5 seconds or more. All conditions are met:
·

Approximately 5 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 10 seconds.
·

CSR OFF indicator light illuminates.

·

Parking brake warning light illuminates.


Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U110687 Lost Communication with Electric Parking Brake Module Missing Message Communication stop occurs between the clearance warning ECU assembly and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 2 seconds or more. All conditions are met:
·

Approximately 2 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 4 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U117787* Lost Communication with Side Obstacle Detection Control "A" (ch2) Missing Message Communication stop occurs between the clearance warning ECU assembly and blind spot monitor sensor LH (A) continuously for approximately 12 seconds or more. All conditions are met:
·

Approximately 12 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 24 seconds. Parking brake warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U117887* Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message Either of the following conditions is met:
·

Communication stop occurs between the clearance warning ECU assembly and blind spot monitor sensor RH (B) continuously for approximately 10 seconds or more.

·

Communication stop occurs between the clearance warning ECU assembly and blind spot monitor sensor RH (B) continuously for approximately 12 seconds or more.


All conditions are met:
·

Approximately 12 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 24 seconds. Parking brake warning light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.
U117987* Lost Communication with Image Processing Module "B" (ch2) Missing Message Either of the following conditions is met:
·

Communication stop occurs between the clearance warning ECU assembly and parking assist ECU continuously for approximately 1 second or more.

·

Communication stop occurs between the clearance warning ECU assembly and parking assist ECU continuously for approximately 5 seconds or more.


All conditions are met:
·

Approximately 5 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the clearance warning ECU assembly is 9 V or higher.


Turn the ignition switch to ON and wait at least approximately 10 seconds. CSR OFF indicator light illuminates. Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


ah.

Parking Assist ECU / GTS Display "Circumference Monitoring Camera Control Module" (w/ Panoramic View Monitor System)

HINT:
·

DTC communication uses the CAN communication system.

·

*1: w/ Navigation System

·

*2: w/o Navigation System



Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 470
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Communication stop occurs between the parking assist ECU and steering sensor continuously for approximately 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - - DTC is stored until it is cleared using the GTS.
U012987 Lost Communication with Brake System Control Module "A" Missing Message Communication stop occurs between the parking assist ECU and brake actuator assembly (No. 2 skid control ECU) continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - - DTC is stored until it is cleared using the GTS.
U013187 Lost Communication with Power Steering Control Module Missing Message Communication stop occurs between the parking assist ECU and rack and pinion power steering gear assembly continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - - DTC is stored until it is cleared using the GTS.
U014087 Lost Communication with Body Control Module Missing Message Communication stop occurs between the parking assist ECU and main body ECU (multiplex network body ECU) continuously for approximately 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 7 seconds. - - DTC is stored until it is cleared using the GTS.
U016387 Lost Communication with Navigation Control Module Missing Message
·

Communication stop occurs between the meter mirror sub-assembly and radio receiver assembly continuously for approximately 5 seconds or more.*1

·

Communication stop occurs between the integration control sub-assembly and radio and display receiver assembly continuously for 10 seconds or more.*2


All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
U023387 Lost Communication with Side Obstacle Detection Control Module "B" Missing Message Communication stop occurs between the parking assist ECU and blind spot monitor sensor RH (B) continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
U023A87 Lost Communication With Image Processing Module "A" Missing Message Communication stop occurs between the parking assist ECU and forward recognition camera continuously for approximately 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.
U026587 Lost Communication with Image Processing Sensor A Missing Message Communication stop occurs between the parking assist ECU and rear television camera assembly continuously for 2 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - - DTC is stored until it is cleared using the GTS.
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the parking assist ECU and EV control ECU continuously for 4 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 7 seconds. - - DTC is stored until it is cleared using the GTS.
U111087 Lost Communication with Clearance Sonar Module Missing Message Communication stop occurs between the parking assist ECU and clearance warning ECU assembly continuously for 11 seconds or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the parking assist ECU is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 14 seconds. - - DTC is stored until it is cleared using the GTS.


ai.

Rear Television Camera Assembly / GTS Display "Rear Camera"

HINT:
·

DTC communication uses the CAN communication system.

·

*1: w/ Navigation System

·

*2: w/o Navigation System



Chassis > Rear Camera > Trouble Codes
50001 85
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0073 Control Module Communication Bus Off Bus off condition is detected. Approximately 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 3 seconds. - - DTC is stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the rear television camera assembly and steering sensor continuously for approximately 11 seconds or more. Approximately 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the rear television camera assembly and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 11 seconds or more. Approximately 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0131 Lost Communication with Power Steering Control Module Communication stop occurs between the rear television camera assembly and rack and pinion power steering gear assembly continuously for approximately 11 seconds or more. Approximately 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module Communication stop occurs between the rear television camera assembly and main body ECU (multiplex network body ECU) continuously for approximately 11 seconds or more. Approximately 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0163 Lost Communication with Navigation Control Module
·

Communication stop occurs between the meter mirror sub-assembly and radio receiver assembly continuously for approximately 5 seconds or more.*1

·

Communication stop occurs between the integration control sub-assembly and radio and display receiver assembly continuously for 10 seconds or more.*2


Approximately 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0233 Lost Communication with Blind Spot Monitor Master Module Communication stop occurs between the rear television camera assembly and blind spot monitor sensor RH (B) continuously for approximately 11 seconds or more. Approximately 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 14 seconds. - - DTC is stored until it is cleared using the GTS.
U023B Lost Communication with Panoramic View Monitor Control Module Communication stop occurs between the rear television camera assembly and parking assist ECU continuously for approximately 11 seconds or more. Approximately 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 14 seconds. - - DTC is stored until it is cleared using the GTS.
U0293 Lost Communication with Hybrid/EV Control Module Communication stop occurs between the rear television camera assembly and EV control ECU continuously for approximately 11 seconds or more. Approximately 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 14 seconds. - - DTC is stored until it is cleared using the GTS.
U1000*3 CAN Communication Failure(Message Registry) CAN message register malfunction is detected. Approximately 3 seconds or more elapse after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately 3 seconds. - - DTC is stored until it is cleared using the GTS.


aj.

Headlight ECU Sub-assembly LH / GTS Display "AFS" (w/ Adaptive High Beam System) / GTS Display "HL AutoLeveling" (w/o Adaptive High Beam System)

HINT:
·

DTC communication uses the CAN communication system.



Body Electrical > AFS > Trouble Codes
50001 165
Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the headlight ECU sub-assembly LH and steering sensor continuously for approximately 10 seconds or more. The power source voltage of the headlight ECU sub-assembly LH is 10 V or higher. Turn the ignition switch to ON and wait at least approximately 10 seconds. - Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the headlight ECU sub-assembly LH and brake actuator assembly (No. 2 skid control ECU) continuously for approximately 10 seconds or more. The power source voltage of the headlight ECU sub-assembly LH is 10 V or higher. Turn the ignition switch to ON and wait at least approximately 10 seconds.
·

Leveling indicator light illuminates.

·

AFS indicator light illuminates.

·

AHS indicator light illuminates.

·

Bad weather indicator light illuminates.


Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0131 Lost Communication with Power Steering Control Module Communication stop occurs between the headlight ECU sub-assembly LH and rack and pinion power steering gear assembly continuously for approximately 10 seconds or more. The power source voltage of the headlight ECU sub-assembly LH is 10 V or higher. Turn the ignition switch to ON and wait at least approximately 10 seconds.
·

AFS indicator light illuminates.

·

AHS indicator light illuminates.


Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0140 Lost Communication with Body Control Module Communication stop occurs between the headlight ECU sub-assembly LH and main body ECU (multiplex network body ECU) continuously for approximately 10 seconds or more. The power source voltage of the headlight ECU sub-assembly LH is 10 V or higher. Turn the ignition switch to ON and wait at least approximately 10 seconds.
·

AFS indicator light illuminates.

·

AHS indicator light illuminates.

·

Bad weather indicator light illuminates.


Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module Communication stop occurs between the headlight ECU sub-assembly LH and combination meter assembly continuously for approximately 10 seconds or more. The power source voltage of the headlight ECU sub-assembly LH is 10 V or higher. Turn the ignition switch to ON and wait at least approximately 10 seconds. - - DTC remains stored only while malfunction is occurring.
U023A* Lost Communication With Image Processing Module "A" Communication stop occurs between the headlight ECU sub-assembly LH and forward recognition camera continuously for approximately 10 seconds or more. The power source voltage of the headlight ECU sub-assembly LH is 10 V or higher. Turn the ignition switch to ON and wait at least approximately 10 seconds. AHS indicator light illuminates. Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0242 Lost Communication With Headlamp Control Module "B" Communication stop occurs between the headlight ECU sub-assembly LH and headlight ECU sub-assembly RH continuously for approximately 10 seconds or more. The power source voltage of the headlight ECU sub-assembly LH is 10 V or higher. Turn the ignition switch to ON and wait at least approximately 10 seconds.
·

Leveling indicator light illuminates.

·

AFS indicator light illuminates.

·

AHS indicator light illuminates.

·

Bad weather indicator light illuminates.


Displays messages on the multi-information display. DTC remains stored only while malfunction is occurring.
U0293 Lost Communication with Hybrid/EV Vehicle Control System Communication stop occurs between the headlight ECU sub-assembly LH and EV control ECU continuously for approximately 10 seconds or more. The power source voltage of the headlight ECU sub-assembly LH is 10 V or higher. Turn the ignition switch to ON and wait at least approximately 10 seconds.
·

Leveling indicator light illuminates.

·

AFS indicator light illuminates.

·

AHS indicator light illuminates.

·

Bad weather indicator light illuminates.


- DTC remains stored only while malfunction is occurring.
U1000* CAN Communication Failure(Message Registry) CAN message register malfunction is detected. The power source voltage of the headlight ECU sub-assembly LH is 10 V or higher. Turn the ignition switch to ON. - - Output during the trip in which the malfunction occurred.


ak.

Headlight ECU Sub-assembly RH / GTS Display "AFS (Sub)" (w/ Adaptive High Beam System) / GTS Display "HL AutoLeveling (Sub)" (w/o Adaptive High Beam System)

HINT:
·

DTC communication uses the CAN communication system.



Body Electrical > AFS (Sub) > Trouble Codes
50001 413
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0126 Lost Communication with Steering Angle Sensor Module Communication stop occurs between the headlight ECU sub-assembly RH and steering sensor continuously for approximately 10 seconds or more. The power source voltage of the headlight ECU sub-assembly RH is 10 V or higher. Turn the ignition switch to ON and wait at least approximately 10 seconds. - - DTC remains stored only while malfunction is occurring.
U0140 Lost Communication with Body Control Module Communication stop occurs between the headlight ECU sub-assembly RH and main body ECU (multiplex network body ECU) continuously for approximately 10 seconds or more. The power source voltage of the headlight ECU sub-assembly RH is 10 V or higher. Turn the ignition switch to ON and wait at least approximately 10 seconds. - - DTC remains stored only while malfunction is occurring.
U0241 Lost Communication With Headlamp Control Module "A" Communication stop occurs between the headlight ECU sub-assembly RH and headlight ECU sub-assembly LH continuously for approximately 10 seconds or more. The power source voltage of the headlight ECU sub-assembly RH is 10 V or higher. Turn the ignition switch to ON and wait at least approximately 10 seconds. - - DTC remains stored only while malfunction is occurring.
U1000* CAN Communication Failure (Message Registry) CAN message register malfunction is detected. The power source voltage of the headlight ECU sub-assembly RH is 10 V or higher. Turn the ignition switch to ON. - - Output during the trip in which the malfunction occurred.


al.

Tire Pressure Warning ECU and Receiver / GTS Display "Tire Pressure Monitor"

HINT:

DTC communication uses the CAN communication system.


Chassis > Tire Pressure Monitor > Trouble Codes
50001 203
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the tire pressure warning ECU and receiver and brake actuator assembly (No. 2 skid control ECU) continuously for 60 seconds or more. Approximately 1 second or more elapses after the ignition switch is ON. Turn the ignition switch to ON and wait at least approximately ○ seconds. - - DTC remains stored only while malfunction is occurring.


am.

Vehicle Approaching Speaker Controller / GTS Display "Vehicle Proximity Notification System" (w/ Acoustic Vehicle Alerting System)

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Vehicle Proximity Notification System > Trouble Codes
50001 393
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U0129 Lost Communication with Brake System Control Module Communication stop occurs between the vehicle approaching speaker controller and brake actuator assembly (No. 2 skid control ECU) continuously for 10 second or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the vehicle approaching speaker controller is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module Communication stop occurs between the vehicle approaching speaker controller and main body ECU (multiplex network body ECU) continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the vehicle approaching speaker controller is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.
U0293 Lost Communication with Hybrid/EV Powertrain Control Module Communication stop occurs between the vehicle approaching speaker controller and EV control ECU continuously for 10 seconds or more. All conditions are met:
·

10 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the vehicle approaching speaker controller is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - - DTC is stored until it is cleared using the GTS.


an.

FC Converter Assembly / GTS Display "FCDC"

HINT:

DTC communication uses the CAN communication system.


Powertrain > FCDC > Trouble Codes
50001 493
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Displayed DTC Storage Method
Indication in Meter Multi-information Display
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message Communication stop occurs between the FC converter assembly and EV control ECU continuously for 1 second or more. All conditions are met:
·

3 seconds or more elapse after the ignition switch is ON.

·

The power source voltage of the FC converter assembly is 10 V or higher.


Turn the ignition switch to ON and wait at least approximately 10 seconds. - Displays messages on the multi-information display. DTC is stored until it is cleared using the GTS.


ao.

Central Gateway ECU (Network Gateway ECU) / GTS Display "Central Gateway"

HINT:

The central gateway ECU (network gateway ECU) is connected to the CAN communication system, but the central gateway ECU (network gateway ECU) does not store or output CAN communication DTCs.



ap.

Steering Sensor / GTS Display "Steering Angle Sensor"

HINT:

The steering sensor is connected to the CAN communication system, but the steering sensor does not store or output CAN communication DTCs.



aq.

Position Control ECU Assembly / GTS Display "Driver Seat" (w/ Seat Position Memory System)

HINT:

The position control ECU assembly is connected to the CAN communication system, but the position control ECU assembly does not store or output CAN communication DTCs.



ar.

Hydrogen Fuel Control ECU Assembly / GTS Display "Hydrogen Filling Control"

HINT:

The hydrogen fuel Control ECU assembly is connected to the CAN communication system, but the hydrogen fuel Control ECU assembly does not store or output CAN communication DTCs.




CAN BUS WAVEFORMS


C353604E02
1.521,0.677 1.854,0.281 1.854,0.281 1.99,0.281 false 4.427,1 4.427,0.271 4.427,0.271 4.563,0.271 true 4.438,3.948 4.438,2.521 4.438,2.521 5.219,2.521 true 6.354,3.948 6.354,2.521 6.354,2.521 5.646,2.521 true 5.375,3.688 5.375,4.781 5.375,4.781 5.51,4.781 false 2.063,0.208 3.208,0.448 1.146,0.24 10 false CAN Main Bus 4.656,0.198 7.052,0.479 2.396,0.281 10 false Open in CAN Main Bus Line (CANH) 5.313,3.167 6.385,3.365 1.073,0.198 10 false ECU 3.417,3.167 4.49,3.365 1.073,0.198 10 false ECU 1.594,3.167 2.667,3.365 1.073,0.198 10 false ECU 3.885,4.01 5.208,4.531 1.323,0.521 10 false Open in CAN Branch Line (CANL) 5.76,4 7.073,4.49 1.313,0.49 10 false Open in CAN Branch Line (CANH) 5.604,4.708 6.708,5.177 1.104,0.469 10 false CAN Branch 1.469,4.781 3.802,5.031 2.333,0.25 10 false : CAN Main Bus Line (CANH) 1.479,5.219 3.677,5.521 2.198,0.302 10 false : CAN Main Bus Line (CANL) 1.479,5.813 3.51,6.094 2.031,0.281 10 false : CAN Branch Line (CANH) 1.469,6.25 3.625,6.521 2.156,0.271 10 false : CAN Branch Line (CANL)

HINT:
·

This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the central gateway ECU (network gateway ECU). (Use this as a reference for diagnosis of CAN communication lines.)

·

When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.

·

If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).

·

Wiggle the connector and wire harness to check if the waveform changes.



a.

CAN bus waveforms (Group 1)

i.
C265973N07
0.49,0.438 0.573,0.438 0.573,0.438 0.906,0.781 true 0.458,1.594 0.552,1.594 0.552,1.594 0.917,1.156 true 0.052,0.333 0.667,0.531 0.615,0.198 10 false CANH 0.031,1.5 0.646,1.698 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.708,0.229 3.427,0.427 0.719,0.198 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Normal waveform


ii.
C265974N05
1.469,1.479 1.552,1.479 1.552,1.479 1.969,1.104 true 1.521,0.49 1.604,0.49 1.604,0.49 1.969,0.792 true 1.094,0.385 1.708,0.583 0.615,0.198 10 false CANH 1.063,1.385 1.677,1.583 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND 2.688,0.229 3.375,0.406 0.688,0.177 10 false 1 V/DIV.

Open in both of the lines (CANH and CANL) of a CAN branch

HINT:
·

Waveforms (waveforms shown using dotted lines) are not output from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)

·

Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.




iii.
C265975N05
1.292,0.917 0.573,0.458 0.573,0.458 0.51,0.458 true 0.469,1.417 0.552,1.417 0.552,1.417 1.063,0.958 true 0.073,0.354 0.688,0.552 0.615,0.198 10 false CANH 0.063,1.323 0.677,1.521 0.615,0.198 10 false CANL 1.344,1.917 2.875,2.115 1.531,0.198 10 false 50 μs/DIV. 2.719,0.229 3.344,0.438 0.625,0.208 10 false 1 V/DIV. 2.958,1.354 3.417,1.552 0.458,0.198 10 false GND

Short between the CAN bus lines (CANH and CANL)

HINT:
·

Waveforms disappear.

·

If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.





b.

CAN bus waveforms (reference) (Group 2)

NOTICE:

The following CAN bus waveforms can be used only as reference. the actual measured waveform may differ significantly depending on the location of the open or short circuit.


i.
C265976N05
0.938,0.76 0.583,0.458 0.583,0.458 0.49,0.458 true 0.458,1.552 0.552,1.552 0.552,1.552 0.854,1.146 true 0.063,0.354 0.677,0.552 0.615,0.198 10 false CANH 0.063,1.458 0.677,1.656 0.615,0.198 10 false CANL 1.313,1.927 2.844,2.125 1.531,0.198 10 false 50 μs/DIV. 2.708,0.229 3.344,0.448 0.635,0.219 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN branch line (CANH)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. the waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




ii.
C265977N05
0.479,1.406 0.573,1.406 0.573,1.406 0.885,1.125 true 0.5,0.438 0.573,0.438 0.573,0.438 0.833,0.74 true 0.063,0.333 0.677,0.531 0.615,0.198 10 false CANH 0.052,1.302 0.667,1.5 0.615,0.198 10 false CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.417,0.458 0.719,0.229 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN branch line (CANL)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. the waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




iii.
C265978N05
0.49,0.406 0.573,0.406 0.573,0.406 0.938,0.708 true 0.469,1.458 0.552,1.458 0.552,1.458 0.938,1.156 true 0.063,0.302 0.677,0.5 0.615,0.198 10 false CANH 0.063,1.365 0.677,1.563 0.615,0.198 10 false CANL 1.323,1.927 2.854,2.125 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.281,0.469 0.583,0.24 10 false 1 V/DIV. 2.969,1.354 3.427,1.552 0.458,0.198 10 false GND

Open in a CAN main bus line (CANH)

HINT:
·

Waveforms of ECUs or sensors that are closer to the central gateway ECU (network gateway ECU) than the open part are almost normal.

·

Waveforms of ECUs or sensors that are on the opposite side of the central gateway ECU (network gateway ECU) from the open part are abnormal.

·

An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.




iv.
C265979N05
0.458,1.813 0.563,1.813 0.563,1.813 1.083,1.531 true 1.063,1.333 0.573,0.906 0.573,0.906 0.49,0.906 true 0.052,0.802 0.667,1 0.615,0.198 10 false CANH 0.042,1.708 0.656,1.906 0.615,0.198 10 false CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 false 50 μs/DIV. 2.719,0.229 3.375,0.479 0.656,0.25 10 false 1 V/DIV. 2.99,1.354 3.385,1.563 0.396,0.208 10 false GND

Short between a CAN bus line (CANH) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.

·

A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.




v.
C265980N05
0.458,1.76 0.563,1.76 0.563,1.76 0.948,1.385 true 0.458,0.5 0.552,0.5 0.552,0.5 1.021,0.708 true 0.031,0.406 0.646,0.604 0.615,0.198 10 false CANH 0.052,1.667 0.667,1.865 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.698,0.229 3.292,0.49 0.594,0.26 10 false 1 V/DIV. 2.969,1.354 3.354,1.604 0.385,0.25 10 false GND

Short between a CAN bus line (CANL) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.

·

A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.