Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › DYNAMIC RADAR CRUISE CONTROL SYSTEM
RM37H0E _95 ADAS / AD _095317 ADVANCED DRIVER ASSISTANCE SYSTEM _0455732 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

ADVANCED DRIVER ASSISTANCE SYSTEM  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK EV CONTROL ECU


A352214C14
0.635,0.115 1.125,0.427 0.49,0.313 1.979,0.302 2.469,0.615 0.49,0.313 3.354,0.302 3.844,0.615 0.49,0.313 4.708,0.302 5.198,0.615 0.49,0.313 5.99,0.115 6.479,0.427 0.49,0.313 5.99,0.49 6.479,0.802 0.49,0.313 0.635,0.49 1.125,0.802 0.49,0.313 0.771,0.188 1.229,0.385 0.458,0.198 10 false A14 2.104,0.396 2.563,0.594 0.458,0.198 10 false A15 3.49,0.396 3.948,0.594 0.458,0.198 10 false A16 4.854,0.406 5.313,0.604 0.458,0.198 10 false A17 6.115,0.188 6.573,0.385 0.458,0.198 10 false D15 6.156,0.563 6.615,0.76 0.458,0.198 10 false A8 6.552,0.198 6.865,0.396 0.313,0.198 10 false *A 6.552,0.573 6.865,0.771 0.313,0.198 10 false *B 0.771,0.563 1.229,0.76 0.458,0.198 10 false G14 1.188,0.198 1.5,0.396 0.313,0.198 10 false *A 1.188,0.573 1.5,0.771 0.313,0.198 10 false *B
*A for RHD *B for LHD


HINT:

The standard voltage, resistance and waveform between each pair of the EV control ECU terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the EV control ECU terminal locations.


Terminal No. (Symbols) Terminal Description Condition Specified Condition

*1: for RHD

*2: for LHD

A17-7 (STP) - A17-4 (E1) Stop light switch assembly signal Brake pedal depressed 11 to 14 V
Brake pedal released 0 to 1.5 V
A16-1 (ST1-) - A17-4 (E1) Stop light switch assembly signal Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 11 to 14 V
D15-8 (CCS) - A17-4 (E1)*1 Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
+RES switch pushed 235 to 245 Ω
-SET switch pushed 617 to 643 Ω
CANCEL switch pushed 1509 to 1571 Ω
A8-8 (CCS) - A17-4 (E1)*2 Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
+RES switch pushed 235 to 245 Ω
-SET switch pushed 617 to 643 Ω
CANCEL switch pushed 1509 to 1571 Ω


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the forward recognition camera connector.



A417823N46
2.063,0.75 2.458,1.01 0.396,0.26 2.188,0.813 2.646,1.01 0.458,0.198 10 false H6

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H6-3 (LKSW) - H6-10 (GND) Steering pad switch assembly signal (distance control signal) Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) off 4.75 to 5.25 V
Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) on Below 1 V
H6-7 (IGB) - H6-10 (GND) Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
H6-10 (GND) - Body ground Ground Always Below 1 Ω