FREEZE FRAME DATA
It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specification.
Turn the ignition switch to ON and park the vehicle on level ground. Check the freeze frame data by using the GTS.
Display the DTCs on the DTC check screen.
Check the freeze frame data on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| Total Distance Traveled - Unit | Total distance traveled unit | - / km / mile | - | - |
| Vehicle Speed | Vehicle speed input from speedometer | 0.0 to 300.0 km/h (0.0 to 186.4 mph) | 0 km/h: Vehicle stopped
No large fluctuations: Vehicle driven at a constant speed |
- |
| Engine Revolution | Engine speed | 0 to 12800 rpm | No large fluctuations: Engine running at a constant speed | - |
| Ready Status | Ignition switch on (READY) status | OFF / ON | OFF: Ignition switch other than on (READY)
ON: Ignition switch on (READY) |
- |
| Battery Voltage | Auxiliary battery voltage | 0.00 to 25.00 V | 11 to 14 V: Ignition switch ON | - |
| Steering Wheel Torque | Steering torque | -25.001 to 25.000 Nm / Unknown | Value changes in proportion to steering force: Ignition switch on (READY) and steering wheel being turned | Steering wheel turned to left (increasing)
Steering wheel turned to right (decreasing) |
| Steering Angle Velocity | Steering angle speed | -32768 to 32767 deg/s | Value changes in proportion to steering force: Ignition switch on (READY) and steering wheel being turned | - |
| Steering Angle | Steering angle | -3072.0 to 3070.5 deg | - | - |
| Status of Vehicle Power (IGP PT2) | IGP power source (PT2) status | OFF / ON | - | This item is displayed but not used |
| Status of Vehicle Power (IGP PT1) | IGP power source (PT1) status | OFF / ON | - | This item is displayed but not used |
| Status of Vehicle Power (IGP PDC) | IGP power source (PDC) status | OFF / ON | - | This item is displayed but not used |
| Status of Vehicle Power (IGR PDC) | IGR power source (PDC) status | OFF / ON | - | This item is displayed but not used |
| IG Power Supply | ECU power source status | 0.00 to 25.00 V | 8 to 16 V: Ignition switch ON | - |
| PIG Power Supply | PIG power source voltage | 0.00 to 25.00 V | 9 to 16 V: Ignition switch on (READY) and power steering operating | - |
| Thermistor Temperature | ECU substrate temperature | -50.0 to 200.0°C (-58 to 392°F) | - | - |
| Power Source | Power source status | Operating State / Stopped State | Operating State: Ignition switch on (READY)
Stopped State: Ignition switch other than on (READY) |
- |
| PS Assist Signal | Power steering assist signal status | Assist Stop / Under an Assist | Assist Stop: Ignition switch ON
Under an Assist: Ignition switch ON (READY) |
- |
| Synchronization Status of PWM | Modulation synchronization state of the motor pulse wave duty ratio | Synchronization State / Non-Synchronization State | Synchronization State: Synchronized
Non-Synchronization State: Not synchronized |
- |
| Cooperation Control State | Power steering operation control state | Cooperation Control / Other than Cooperation Control | Cooperation Control: Cooperation control
Other than Cooperation Control: Other than cooperation control |
- |
| Middle Voltage of Other Systems | Middle voltage of other systems | 0.00 to 25.00 V | - | - |
| Torque Sensor 1 Output | Output value of torque sensor 1 | -25.000 to 25.000 Nm | - | - |
| Torque Sensor 2 Output | Output value of torque sensor 2 | -25.000 to 25.000 Nm | - | - |
| Torque Sensor 3 Output | Output value of torque sensor 3 | -25.000 to 25.000 Nm | - | - |
| Torque Sensor 4 Output | Output value of torque sensor 4 | -25.000 to 25.000 Nm | - | - |
| Motor 1 U Phase Current | Motor 1 terminal current (U phase) | -327.68 to 327.67 A | - | - |
| Motor 1 V Phase Current | Motor 1 terminal current (V phase) | -327.68 to 327.67 A | - | - |
| Motor 1 W Phase Current | Motor 1 terminal current (W phase) | -327.68 to 327.67 A | - | - |
| Motor 1 U Phase Duty | Motor 1 terminal duty ratio (U phase) | 0.00 to 100.00 % | - | - |
| Motor 1 V Phase Duty | Motor 1 terminal duty ratio (V phase) | 0.00 to 100.00 % | - | - |
| Motor 1 W Phase Duty | Motor 1 terminal duty ratio (W phase) | 0.00 to 100.00 % | - | - |
| Motor 1 U Phase Terminal Voltage | Motor 1 U phase terminal voltage | 0.00 to 100.00 V | - | - |
| Motor 1 V Phase Terminal Voltage | Motor 1 V phase terminal voltage | 0.00 to 100.00 V | - | - |
| Motor 1 W Phase Terminal Voltage | Motor 1 W phase terminal voltage | 0.00 to 100.00 V | - | - |
| Motor 1 Power Supply | Motor 1 power source voltage | 0.00 to 25.00 V | 9 to 16 V: Ignition switch ON (READY) and power steering operating | - |
| Motor 2 U Phase Current | Motor 2 terminal current (U phase) | -327.68 to 327.67 A | Value changes in proportion to steering force: Ignition switch ON (READY) and steering wheel being turned | - |
| Motor 2 V Phase Current | Motor 2 terminal current (V phase) | -327.68 to 327.67 A | Value changes in proportion to steering force: Ignition switch ON (READY) and steering wheel being turned | - |
| Motor 2 W Phase Current | Motor 2 terminal current (W phase) | -327.68 to 327.67 A | Value changes in proportion to steering force: Ignition switch ON (READY) and steering wheel being turned | - |
| Motor 2 U Phase Duty | Motor 2 terminal duty ratio (U phase) | 0.00 to 100.00 % | - | - |
| Motor 2 V Phase Duty | Motor 2 terminal duty ratio (V phase) | 0.00 to 100.00 % | - | - |
| Motor 2 W Phase Duty | Motor 2 terminal duty ratio (W phase) | 0.00 to 100.00 % | - | - |
| Motor 2 U Phase Terminal Voltage | Motor 2 U phase terminal voltage | 0.00 to 100.00 V | - | - |
| Motor 2 V Phase Terminal Voltage | Motor 2 V phase terminal voltage | 0.00 to 100.00 V | - | - |
| Motor 2 W Phase Terminal Voltage | Motor 2 W phase terminal voltage | 0.00 to 100.00 V | - | - |
| Motor 2 Power Supply | Motor 2 power source voltage | 0.00 to 25.00 V | 9 to 16 V: Ignition switch ON (READY) and power steering operating | - |
| Motor Rotation Angle 1 | Motor rotation angle 1 | 0.0 to 360.1 deg / Unknown | - | - |
| Motor Rotation Angle 2 | Motor rotation angle 2 | 0.0 to 360.1 deg / Unknown | - | - |
| Motor Rotation Angle 3 | Motor rotation angle 3 | 0.0 to 360.1 deg / Unknown | - | - |
| Motor Rotation Angle 4 | Motor rotation angle 4 | 0.0 to 360.1 deg / Unknown | - | - |
| Motor Rotation Angle Sensor 1 Sin Voltage | Sin voltage of motor rotation angle sensor 1 | 0.00 to 5.00 V | - | This item is displayed but not used |
| Motor Rotation Angle Sensor 1 Cos Voltage | Cos voltage of motor rotation angle sensor 1 | 0.00 to 5.00 V | - | This item is displayed but not used |
| Motor Rotation Angle Sensor 2 Sin Voltage | Sin voltage of motor rotation angle sensor 2 | 0.00 to 5.00 V | - | This item is displayed but not used |
| Motor Rotation Angle Sensor 2 Cos Voltage | Cos voltage of motor rotation angle sensor 2 | 0.00 to 5.00 V | - | This item is displayed but not used |
| Motor Rotation Angle Sensor 3 Sin Voltage | Sin voltage of motor rotation angle sensor 3 | 0.00 to 5.00 V | - | This item is displayed but not used |
| Motor Rotation Angle Sensor 3 Cos Voltage | Cos voltage of motor rotation angle sensor 3 | 0.00 to 5.00 V | - | This item is displayed but not used |
| Turn Counter 1 | Turn counter 1 | 0 to 1024 | - | - |
| Turn Counter 2 | Turn counter 2 | 0 to 1024 | - | - |
| Absolute Angle (Pinion Angle) | Absolute angle (Pinion angle) | -32.768 to 32.768 rad | - | - |
| Steering Angle for the Steering Assembly | Steering angle for the steering assembly | -1877.5 to 1877.6 deg / Unknown | - | - |
| Motor Actual Current (Q Axis) | Motor current (q axis) | -327.68 to 327.67 A | - | - |
| Command Value Current (Q Axis) | Motor command current (q axis) | -327.68 to 327.67 A | - | - |
| Motor Actual Current 2 (D Axis) | Motor current 2 (d axis) | -327.68 to 327.67 A | - | - |
| Command Value Current 2 (D Axis) | Motor command current 2 (d axis) | -327.68 to 327.67 A | - | - |
| Motor Rotation Angle | Motor rotation angle | 0.0 to 360.1 deg / Unknown | Value changes from 0 to 360°: Ignition switch ON (READY) and steering wheel being turned | - |
| Final Motor Current limited (Q Axis) | Final motor current limit value (q axis) | 0.00 to 327.67 A | - | - |
| Steering Angle Sensor Signal State | Steering angle sensor signal status | Usable / Unlearned / Sensor Fault / Communication Fault | - | - |
| Eco-Run Control Mode | Engine stop and start system control mode | Eco Mode0 / Eco Mode1 / Eco Mode2 / Eco Mode3 / Eco Mode4 | - | This item is displayed but not used |
| CAN Vehicle Speed (Speed Sensor RR) | Vehicle speed on the rear speed sensor RH input via CAN communication | 0 to 255 km/h (0 to 158 mph) | 0 km/h: Vehicle stopped
No large fluctuations: Vehicle driven at a constant speed |
- |
| CAN Vehicle Speed (Speed Sensor RL) | Vehicle speed on the rear speed sensor LH input via CAN communication | 0 to 255 km/h (0 to 158 mph) | 0 km/h: Vehicle stopped
No large fluctuations: Vehicle driven at a constant speed |
- |
| CAN Vehicle Speed (SP1) | Vehicle speed input via CAN communication | 0.0 to 300.0 km/h (0.0 to 186.4 mph) | 0 km/h: Vehicle stopped
No large fluctuations: Vehicle driven at a constant speed |
- |
| CAN Steering Angle Speed (SSAV) | Steering angle velocity input via CAN communication | -32768 to 32767 deg/s | - | - |
| Control State Information | Control status information | 0 to 65535 | - | - |
| ASIC State Information | Integrated circuit state information | 0 to 65535 | - | - |
| ECU Overheat Prevention Part | Target parts for ECU overheat prevention | No Target Part / IPWM / Inverter MOS / Power Supply Relay MOS / Custom IC / Choke Coil / H Bridge MOS / Motor Relay MOS / Around Microcomputer / Capacitor / Microcomputer / DBC | - | - |
| ECU Estimate Temperature of Overheat Prevention Part | Estimated temperature of target parts for ECU overheat prevention | -50.0 to 200.0°C (-58 to 392.1°F) / Unknown | - | - |
| Motor Overheat Prevention Part | Target parts for motor overheat prevention | No Target Part / Motor | - | - |
| Motor Estimate Temperature of Overheat Prevention Part | Estimated temperature of target parts for motor overheat prevention | -50.0 to 200.0°C (-58 to 392.1°F) / Unknown | - | - |
| Battery Voltage (System 2) | Auxiliary battery voltage (System 2) | 0.00 to 25.00 V | 11 to 14 V: Ignition switch ON | - |
| IG Power Supply (System 2) | ECU power supply status (System 2) | 0.00 to 25.00 V | 8 to 16 V: Ignition switch ON | - |
| PIG Power Supply (System 2) | PIG power supply voltage (System 2) | 0.00 to 25.00 V | 9 to 16 V: Ignition switch ON (READY) and power steering operating | - |
| Thermistor Temperature (System 2) | ECU substrate temperature (System 2) | -50.0 to 200.0°C (-58 to 392°F) | - | - |
| Middle Voltage of Other Systems (System 2) | Middle voltage of other systems (System 2) | 0.00 to 25.00 V | - | - |
| Motor Actual Current (Q Axis) (System 2) | Motor current (Q axis) (System 2) | -327.68 to 327.67 A | - | - |
| Command Value Current (Q Axis) (System 2) | Motor command current (Q axis) (System 2) | -327.68 to 327.67 A | - | - |
| Motor Actual Current 2 (D Axis) (System 2) | Motor current 2 (D axis) (System 2) | -327.68 to 327.67 A | - | - |
| Command Value Current 2 (D Axis) (System 2) | Motor command current 2 (D axis) (System 2) | -327.68 to 327.67 A | - | - |
| Motor Rotation Angle (System 2) | Motor rotation angle (System 2) | 0.0 to 360.0 deg / Unknown | Value changes from 0 to 360°: Ignition switch ON (READY) and steering wheel being turned | - |
| Final Motor Current Limited (Q Axis) (System 2) | Final motor current limit value (Q axis) (System 2) | 0.00 to 327.67 A | - | - |
| ASIC State Information (System 2) | Integrated circuit state information (System 2) | 0 to 65535 | - | - |