Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM37H0E _58 Vehicle Interior _095292 SEAT _0457023 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) M

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  REGISTRATION  


PROCEDURE

Hide 1. MEMORY CALL REGISTRATION

*1: for LHD

*2: for RHD


a.

Memory registration

NOTICE:
·

Do not bring 2 or more electrical key transmitter sub-assemblies into the cabin.

·

Do not press and hold the door control switch on the multiplex network master switch for 3 seconds or more.



i.

Register the seat position to a seat memory switch LH*1 or RH*2 (M1 or M2 switch) in advance.


ii.

Sit on the driver seat carrying only the electrical key transmitter sub-assembly to which a seat position is to be registered.


iii.

With the ignition switch ON and the shift lever in P, restore the seat to the memorized position to be registered.


iv.

With the ignition switch ON, the shift lever in P, the driver door closed and a seat memory switch LH*1 or RH*2 (M1 or M2 switch) being pressed and held, press and hold the door control switch on the multiplex network master switch until the buzzer answer-back function operates.

HINT:
·

The door control switch on the multiplex network master switch can be pressed to either the lock or unlock side.

·

The buzzer will sound for 0.5 seconds when the registration is complete.

·

The buzzer will sound for 3 seconds if the registration fails.





b.

Memory registration when using the GTS

i.

Enter the following menus: Body Electrical / Entry&Start / Utility / Driver Information Registration.

Body Electrical > Entry&Start > Utility
Tester Display
Driver Information Registration
50005 125 2105


c.

Memory deletion

NOTICE:
·

Do not bring 2 or more electrical key transmitter sub-assemblies into the cabin.

·

Do not press and hold the door control switch on the multiplex network master switch for 3 seconds or more.



i.

Sit on the driver seat carrying only the electrical key transmitter sub-assembly from which the seat position is to be deleted.


ii.

With the ignition switch ON, the shift lever in P, the driver door closed and the SET seat memory switch being pressed and held, press and hold the door control switch on the multiplex network master switch until the answer-back by the buzzer is confirmed.

HINT:
·

The door control switch on the multiplex network master switch can be pressed to either the lock or unlock side.

·

The buzzer will sound for 0.5 seconds when the memory deletion is complete.

·

The buzzer will sound for 3 seconds if the memory deletion fails.





Hide 2. POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) INITIALIZATION

*1: for LHD

*2: for RHD


NOTICE:

Initializing the position control ECU assembly LH*1 or RH*2 will clear the seat position memory.


HINT:
·

Make sure to initialize the position control ECU assembly LH*1 or RH*2 after replacing the seat assembly or any related parts (including removal and installation).

·

Before initializing the position control ECU assembly LH*1 or RH*2, make sure that the D/C CUT NO.1 fuse is normal.

·

When any of the following conditions are met, the seat position information in the position control ECU assembly LH*1 or RH*2 will be cleared.

-

The ignition switch is turned off with any of the seat switches being operated and the D/C CUT NO.1 fuse removed.

-

The ignition switch is turned off within 1 second of any of the seat switches being operated with the D/C CUT fuse NO.1 removed.




E457220C02
4.469,1.667 4.458,0.854 4.458,0.854 4.583,0.854 true 5.229,1.583 5.396,0.958 5.396,0.958 5.521,0.958 true 0.135,0.094 0.594,0.469 0.458,0.375 10 false *a 4.625,0.802 4.917,1.031 0.292,0.229 10 false *1 5.573,0.906 5.844,1.167 0.271,0.26 10 false *2
*a example - -
*1
·

Slide switch

·

Front vertical switch

·

Rear lifter switch


*2 Reclining switch


a.

Reset the ECU:

i.

Turn the ignition switch to ON.


ii.

Operate the front vertical switch downward 3 times.


iii.

Operate the rear lifter switch upward within 10 seconds of operating the front vertical switch. Simultaneously operate the reclining switch backward and hold the switches in operation until the buzzer sounds.



b.

Set the ECU 0 value:

i.

Operate the slide switch and move the seat to its operating limit position (front). Hold the slide switch in that position for 1 second.


ii.

Operate the slide switch and move the seat to its operating limit position (rear). Hold the slide switch in that position for 1 second.


iii.

Operate the rear lifter switch and move the seat to its operating limit position (down). Hold the rear lifter switch in that position for 1 second.


iv.

Operate the reclining switch and move the seat to its operating limit position (front). Hold the reclining switch in that position for 1 second.

HINT:

The above steps of this procedure can be performed in any order.




c.

Operate any switch and check that the buzzer does not sound. (Check that initialization is complete)