Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/o Memory)
RM37H0E _58 Vehicle Interior _095292 SEAT _0457024 FRONT POWER SEAT CONTROL SYSTEM(w/o Memory) D

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/o Memory)  OPERATION CHECK  


CHECK POWER SEAT FUNCTION (Driver Seat)


a.
E457498C05
1.771,2.677 2.333,2.792 2.333,2.792 2.5,2.792 true 1.927,3.052 2.49,3.167 2.49,3.167 2.656,3.167 true 0.75,2.427 0.531,2.125 0.531,2.125 0.365,2.125 true 2.594,2.104 2.729,1.906 2.729,1.906 2.896,1.906 true 2.531,1.271 2.667,1.073 2.667,1.073 2.833,1.073 true 1.479,1.333 1.26,1.031 1.26,1.031 1.094,1.031 true 2.552,2.708 2.865,2.906 0.313,0.198 10 false *1 2.719,3.073 3.031,3.271 0.313,0.198 10 false *a 0.198,2.042 0.51,2.24 0.313,0.198 10 false *b 2.938,1.823 3.25,2.021 0.313,0.198 10 false *c 2.896,1.01 3.208,1.208 0.313,0.198 10 false *d 0.896,0.948 1.208,1.146 0.313,0.198 10 false *e
*1 Front Power Seat Switch LH
*a Slide function
*b Front vertical function
*c Lifter function
*d Reclining function
*e Lumbar support adjustment function


Check the basic functions. (for LHD)

i.

Operate the front power seat switch LH and check that the following seat functions operate properly:

·

Slide function

·

Reclining function

·

Lifter function

·

Front vertical function

·

Lumbar support adjustment function




b.
E394667C08
1.177,3.24 1.313,3.24 1.313,3.24 1.542,2.958 true 2.865,2.844 2.74,2.844 2.74,2.844 2.573,2.583 true 0.427,1.948 0.552,1.948 0.552,1.948 0.823,2.094 true 0.5,0.885 0.625,0.885 0.625,0.885 1,1.333 true 2.542,0.927 2.417,0.927 2.417,0.927 1.927,1.385 true 2.115,3.25 2,3.25 2,3.25 1.688,2.656 true 1.021,3.135 1.25,3.313 0.229,0.177 10 false *a 2.885,2.74 3.156,3 0.271,0.26 10 false *d 0.271,1.844 0.448,2 0.177,0.156 10 false *c 0.333,0.792 0.563,1.031 0.229,0.24 10 false *b 2.583,0.823 2.76,0.979 0.177,0.156 10 false *e 2.146,3.146 2.323,3.302 0.177,0.156 10 false *1
*1 Front Power Seat Switch RH
*a Slide function
*b Reclining function
*c Lifter function
*d Front vertical function
*e Lumbar support adjustment function


Check the basic functions. (for RHD)

i.

Operate the front power seat switch RH and check that the following seat functions operate properly:

·

Slide function

·

Reclining function

·

Lifter function

·

Front vertical function

·

Lumbar support adjustment function





CHECK POWER SEAT FUNCTION (Front Passenger Seat)


a.
E462812C05
0.958,3.271 1.094,3.271 1.094,3.271 1.375,3.104 true 0.354,0.833 0.479,0.833 0.479,0.833 0.854,1.281 true 2.354,3.156 2.24,3.156 2.24,3.156 1.594,2.792 true 0.792,3.188 1.021,3.323 0.229,0.135 10 false *a 0.188,0.771 0.448,1.042 0.26,0.271 10 false *b 2.396,3.094 2.635,3.271 0.24,0.177 10 false *1
*1 Front Power Seat Switch RH
*a Slide function
*b Reclining function


Check the basic functions. (for LHD)

i.

Operate the front power seat switch RH and check that the following seat functions operate properly:

·

Slide function

·

Reclining function




b.
E462811C05
2.792,1.49 2.896,1.073 2.896,1.073 3.083,1.073 true 0.792,1.531 0.969,1.531 0.969,1.531 2.156,2.677 true 2.688,3.292 2.521,3.292 2.521,3.292 2.313,3.042 true 3.115,0.99 3.333,1.26 0.219,0.271 10 false *b 0.625,1.458 0.875,1.75 0.25,0.292 10 false *1 2.698,3.188 2.917,3.385 0.219,0.198 10 false *a
*1 Front Power Seat Switch LH
*a Slide function
*b Reclining function


Check the basic functions. (for RHD)

i.

Operate the front power seat switch LH and check that the following seat functions operate properly:

·

Slide function

·

Reclining function





CHECK POWER SEAT MOTOR (SLIDE, FRONT VERTICAL, LIFTER AND RECLINING FUNCTIONS) (for Driver Seat)


*1: for LHD

*2: for RHD


a.

Check the PTC operation inside the power seat motor.

NOTICE:
·

The inspection should be performed with the seat installed to the vehicle.

·

Perform the 4 steps below to check the full range of motion for each power seat function.



HINT:

The resistance of the PTC thermistor increases when a switch of the front power seat switch LH*1 or RH*2 is held down even after the seat has been moved to the farthest possible position in one direction. If the resistance increases beyond a specified level, the current is shut off to prevent a short circuit.


i.

Choose a power seat function. Operate a switch of the front power seat switch LH*1 or RH*2 and move the seat to the farthest possible position in one direction. Keep the seat in that position for approximately 60 seconds.


ii.

Operate the switch of the front power seat switch LH*1 or RH*2 again and continue to try to move the seat in the same direction as in the previous step. Measure the time until the current is shut off (motor operation sound stops).

Standard:

4 to 90 seconds



iii.

After the current is shut off, release the switch of the front power seat switch LH*1 or RH*2 and wait for approximately 60 seconds.


iv.

Operate a switch of the front power seat switch LH*1 or RH*2 and move the seat in the opposite direction. Check that the motor operates.




CHECK POWER SEAT MOTOR (SLIDE, RECLINING FUNCTIONS) (for Passenger Seat)


*1: for LHD

*2: for RHD


a.

Check the PTC operation inside the power seat motor.

NOTICE:
·

The inspection should be performed with the seat installed to the vehicle.

·

Perform the 4 steps below to check the full range of motion for each power seat function.



HINT:

The resistance of the PTC thermistor increases when a switch of the front power seat switch RH*1 or LH*2 is held down even after the seat has been moved to the farthest possible position in one direction. If the resistance increases beyond a specified level, the current is shut off to prevent a short circuit.


i.

Choose a power seat function. Operate a switch of the front power seat switch RH*1 or LH*2 and move the seat to the farthest possible position in one direction. Keep the seat in that position for approximately 60 seconds.


ii.

Operate the switch of the front power seat switch RH*1 or LH*2 again and continue to try to move the seat in the same direction as in the previous step. Measure the time until the current is shut off (motor operation sound stops).

Standard:

4 to 90 seconds



iii.

After the current is shut off, release the switch of the front power seat switch RH*1 or LH*2 and wait for approximately 60 seconds.


iv.

Operate a switch of the front power seat switch RH*1 or LH*2 and move the seat in the opposite direction. Check that the motor operates.




CHECK LUMBAR SUPPORT ADJUSTMENT MOTOR


*1: for LHD

*2: for RHD


a.

Check the PTC operation inside the lumbar support adjustment motor.

NOTICE:

The inspection should be performed with the seat installed to the vehicle.


i.

Operate the front power seat switch LH*1 or RH*2 and move the lumbar support to either the foremost or rearmost position. Keep the seat in that position for approximately 60 seconds.


ii.

Operate the front power seat switch LH*1 or RH*2 again and continue to try to move the lumbar support in the same direction as in the previous step. Measure the time until the current is shut off (motor operation sound stops).

Standard:

4 to 90 seconds



iii.

After the current is shut off, release the front power seat switch LH*1 or RH*2 and wait for approximately 60 seconds.


iv.

Operate the front power seat switch LH*1 or RH*2 and move the lumbar support in the opposite direction. Check that the motor operates.