Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM
RM37H0E _58 Vehicle Interior _095292 SEAT _0457025 SEAT HEATER SYSTEM U

SEAT  SEAT HEATER SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


E407961N14
1.75,0.146 2.104,0.406 0.354,0.26 2.76,0.146 3.115,0.406 0.354,0.26 3.74,0.146 4.094,0.406 0.354,0.26 4.74,0.146 5.094,0.406 0.354,0.26 5.583,0.146 5.938,0.406 0.354,0.26 1.802,0.198 2.115,0.375 0.313,0.177 10 false D78 2.823,0.198 3.219,0.406 0.396,0.208 10 false D79 3.802,0.198 4.115,0.375 0.313,0.177 10 false D80 4.792,0.198 5.104,0.375 0.313,0.177 10 false D81 5.677,0.188 5.99,0.365 0.313,0.177 10 false z1

a.

Disconnect the D81 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D81-6 (IG+) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
D81-17 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the D81 air conditioning amplifier assembly connector.


d.

Measure the voltage, resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/ Rear Seat Heater

D79-14 (SM1R) - Body ground RH side front seat heater drive signal
·

Ignition switch ON

·

Front right side seat heater switch (multi-display or air conditioning controller assembly) on


Below 1 V
D79-13 (SM1L) - Body ground LH side front seat heater drive signal
·

Ignition switch ON

·

Front left side seat heater switch (multi-display or air conditioning controller assembly) on


Below 1 V
D78-3 (SG-7) - Body ground Ground for front seat heater sensor Always Below 1 Ω
D78-12 (TSR) - Body ground RH side front seat heater sensor input signal - -
D78-13 (TSL) - Body ground LH side front seat heater sensor input signal - -
D81-7 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
D79-23 (SM2R) - Body ground* RH side rear seat heater drive signal
·

Ignition switch ON

·

Rear right side seat heater (rear) switch on


Below 1 V
D79-24 (SM2L) - Body ground* LH side rear seat heater drive signal
·

Ignition switch ON

·

Rear left side seat heater (rear) switch on


Below 1 V



CHECK REFRESHING SEAT SWITCH (SEAT HEATER SWITCH)


E407962N06
3.396,0.135 3.75,0.375 0.354,0.24 3.458,0.177 3.802,0.438 0.344,0.26 10 false D90

a.

Disconnect the D90 refreshing seat switch (seat heater switch) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D90-4 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
D90-8 (E) - Body ground Ground Always Below 1 Ω


c.

Reconnect the D90 refreshing seat switch (seat heater switch) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D90-3 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK AIR CONDITIONING CONTROL ASSEMBLY (w/ Rear Seat Heater)


E389743N13
3.354,0.167 3.854,0.417 0.5,0.25 3.469,0.208 3.927,0.406 0.458,0.198 10 false I1

a.

Disconnect the I1 air conditioning control assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I1-9 (IG+) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
I1-16 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the I1 air conditioning control assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I1-13 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation