Home › Vehicle Interior › SEAT › CLIMATE CONTROL SEAT SYSTEM
RM37H0E _58 Vehicle Interior _095292 SEAT _0457026 CLIMATE CONTROL SEAT SYSTEM U

SEAT  CLIMATE CONTROL SEAT SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


E411397E04
1.729,0.49 2.115,0.75 0.385,0.26 2.667,0.49 3.052,0.75 0.385,0.26 3.698,0.479 4.083,0.74 0.385,0.26 4.74,0.479 5.125,0.74 0.385,0.26 5.583,0.479 5.969,0.74 0.385,0.26 1.802,0.552 2.198,0.75 0.396,0.198 10 false D78 2.729,0.542 3.104,0.75 0.375,0.208 10 false D79 3.771,0.552 4.177,0.781 0.406,0.229 10 false D80 4.813,0.552 5.177,0.76 0.365,0.208 10 false D81 5.698,0.521 6.063,0.729 0.365,0.208 10 false z1

a.

Disconnect the D81 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D81-6 (IG+) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
D81-17 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the D81 air conditioning amplifier assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/ Rear Climate Control Seat

D81-7 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
D81-13 (ROUT) - Body ground Front passenger side seat blower control signal
·

Ignition switch ON

·

Front passenger side refreshing seat switch (seat blower switch) operate


Pulse generation
(See waveform)
D81-14 (LOUT) - Body ground Driver side seat blower control signal
·

Ignition switch ON

·

Driver side refreshing seat switch (seat blower switch) operate


Pulse generation
(See waveform)
D79-20 (RLIN) - Body ground LIN communication line Ignition switch ON Pulse generation
D79-21 (SV2R) - Body ground* Rear right side seat blower control signal
·

Ignition switch ON

·

Rear right side refreshing seat switch (seat blower switch) operate


Pulse generation
(See waveform)
D79-22 (SV2L) - Body ground* Rear left side seat blower control signal
·

Ignition switch ON

·

Rear left side refreshing seat switch (seat blower switch) operate


Pulse generation
(See waveform)

i.
B295627N02
0.156,1.594 0.594,1.833 0.438,0.24 10 false GND

Waveform (Reference):

Measurement Condition
Item Content

*: w/ Rear Climate Control Seat

Tester Connection
·

D81-13 (ROUT) - Body ground

·

D81-14 (LOUT) - Body ground

·

D79-21 (SV2R) - Body ground*

·

D79-22 (SV2L) - Body ground*


Tool Setting 1 V/DIV., 1 ms/DIV.
Vehicle Condition
·

Ignition switch ON

·

Driver side refreshing seat switch (seat blower switch) operate

·

Front passenger side refreshing seat switch (seat blower switch) operate

·

Rear right side refreshing seat switch (seat blower switch) operate*

·

Rear left side refreshing seat switch (seat blower switch) operate*






AIR CONDITIONING CONTROL ASSEMBLY


E407962N05
3.396,0.135 3.75,0.375 0.354,0.24 3.458,0.177 3.74,0.354 0.281,0.177 10 false D90

a.

Disconnect the D90 air conditioning control assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D90-4 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
D90-8 (E) - Body ground Ground Always Below 1 Ω


c.

Reconnect the D90 air conditioning control assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D90-3 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK COOLER CONTROL SWITCH ASSEMBLY (w/ Rear Climate Control Seat)


E389743N12
3.354,0.167 3.854,0.417 0.5,0.25 3.5,0.208 3.958,0.406 0.458,0.198 10 false I1

a.

Disconnect the I1 cooler control switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I1-9 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
I1-16 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the I1 cooler control switch assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I1-13 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation