Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › COOLANT (for Inverter)
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0457179 COOLANT(for Inverter) G

HYBRID / BATTERY CONTROL  COOLANT(for Inverter)  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A479337

To avoid the danger of being burned, do not remove the inverter reserve tank cap while the coolant (for inverter) is still hot. Pressurized, hot coolant (for inverter) and steam may be released and cause serious burns.


PROCEDURE

Hide 1.INSPECT FOR COOLANT LEAK (for Inverter)

CAUTION:
A479337

To avoid the danger of being burned, do not remove the inverter reserve tank cap while the coolant (for inverter) is still hot. Pressurized, hot coolant (for inverter) and steam may be released and cause serious burns.


Pre-procedure1

a.

Remove the inverter reserve tank cap from the inverter reserve tank assembly.


b.

Add coolant to the MAX line of the inverter reserve tank assembly.


c.
A479338

Install a radiator cap tester to the inverter reserve tank assembly.


Procedure1

a.

Pump the radiator cap tester to 122 kPa (1.2 kgf/ cm2, 18 psi), and then check that the pressure does not drop.

HINT:
·

If the pressure drops, check the hoses, radiator assembly, inverter water pump assembly, hybrid vehicle transaxle assembly, and inverter with converter assembly for leaks.

·

If there are signs of coolant leakage the inverter water pump assembly, replace the inverter water pump assembly.




Post-procedure1

a.

Reinstall the inverter reserve tank cap to the inverter reserve tank assembly.


Hide 2.INSPECT COOLANT LEVEL IN RESERVE TANK (for Inverter)

a.
A477091

The coolant should be between the MIN and MAX lines when the coolant (for inverter) is cold.

HINT:

If the coolant level is MIN, check for leaks and add TOYOTA Super Long Life Coolant (SLLC) or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology up to the MAX line.



Hide 3.INSPECT COOLANT QUALITY (for Inverter)

CAUTION:
A479337

To avoid the danger of being burned, do not remove the inverter reserve tank cap while the coolant (for inverter) is still hot. Pressurized, hot coolant (for inverter) and steam may be released and cause serious burns.


Pre-procedure1

a.

Remove the inverter reserve tank cap from the inverter reserve tank assembly.


Procedure1

a.

Check for excessive deposits of rust or scale on and around the inverter reserve tank cap and its opening.

HINT:

If excessively dirty, replace the coolant (for inverter).



Post-procedure1

a.

Reinstall the inverter reserve tank cap to the inverter reserve tank assembly.


Hide 16475 4.INSPECT RESERVE TANK CAP (for Inverter)

a.
A215769C05
1.188,1.5 0.823,1.5 false 2.01,1.271 2.74,1.271 false 2.74,1.5 2.729,1.51 false 0.635,1.417 1.01,1.74 0.375,0.323 10 *a 2.75,1.188 3.083,1.688 0.333,0.5 10 *b
*a O-ring
*b Rubber Packing


Inspect the inverter reserve tank cap.

i.

If there are water stains or foreign matter on the O-ring, clean it with water and finger scouring.

NOTICE:

Do not use any tools.



ii.

Check that the O-ring is not deformed, cracked, or damaged.


iii.

Check that the O-ring is not swollen.



b.
A249860C12
2.104,0.156 1.938,0.156 1.938,0.156 1.625,0.469 false 0.979,0.26 0.813,0.26 0.813,0.26 0.5,0.573 false 1.021,0.188 1.24,0.427 0.219,0.24 10 false *1 2.135,0.094 2.406,0.375 0.271,0.281 10 false *a 0.667,1.073 0.906,1.313 0.24,0.24 10 false *b
*1 Inverter Reserve Tank Cap
*a Radiator Cap Tester
*b 30° or more


Check the inverter reserve tank cap operation.

i.

Apply coolant to the O-ring and rubber packing before using a radiator cap tester.


ii.

Install the inverter reserve tank cap to the radiator cap tester.


iii.

Pump the radiator cap tester several times and check the maximum pressure.

Pumping speed:

1 pump per second


Result:
Item Specified Condition
Standard pressure
(for brand-new reserve tank cap)
94 to 122 kPa
1.0 to 1.2 kgf/cm2
14 to 18 psi
Minimum pressure
(for used reserve tank cap)
94 kPa
1.0 kgf/cm2
14 psi


NOTICE:

When using the radiator cap tester, tilt it upward 30° or more.


HINT:

If the maximum pressure is less than the minimum standard value, replace the inverter reserve tank cap.