Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › RELAY
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0457189 RELAY G

HYBRID / BATTERY CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85924C 1.INSPECT IGNITION CONTACT RELAY (IGCT NO. 1)

a.
E222294N65
1.073,0.958 1.302,0.49 1.302,0.49 1.438,0.49 false 1.063,1.333 1.146,1.75 1.146,1.75 1.344,1.75 false 0.802,1.01 0.938,0.49 0.938,0.49 1.063,0.49 false 0.563,1.281 0.635,1.76 0.635,1.76 0.823,1.76 false 1.458,0.406 1.563,0.563 0.104,0.156 10 1 1.375,1.667 1.479,1.823 0.104,0.156 10 2 1.094,0.396 1.198,0.552 0.104,0.156 10 5 0.844,1.667 0.948,1.823 0.104,0.156 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the ignition contact relay (IGCT No. 1).


Hide 85924C 2.INSPECT IGNITION CONTACT RELAY (IGCT NO. 2)

a.
E222294N65
1.073,0.958 1.302,0.49 1.302,0.49 1.438,0.49 false 1.063,1.333 1.146,1.75 1.146,1.75 1.344,1.75 false 0.802,1.01 0.938,0.49 0.938,0.49 1.063,0.49 false 0.563,1.281 0.635,1.76 0.635,1.76 0.823,1.76 false 1.458,0.406 1.563,0.563 0.104,0.156 10 1 1.375,1.667 1.479,1.823 0.104,0.156 10 2 1.094,0.396 1.198,0.552 0.104,0.156 10 5 0.844,1.667 0.948,1.823 0.104,0.156 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the ignition contact relay (IGCT No. 2).


Hide 16100P 3.INSPECT INV WATER PUMP RELAY (INV W/PMP)

a.
E222294N64
1.073,0.958 1.302,0.49 1.302,0.49 1.438,0.49 false 1.063,1.333 1.146,1.75 1.146,1.75 1.344,1.75 false 0.802,1.01 0.938,0.49 0.938,0.49 1.063,0.49 false 0.563,1.281 0.635,1.76 0.635,1.76 0.823,1.76 false 1.458,0.406 1.563,0.563 0.104,0.156 10 1 1.375,1.667 1.479,1.823 0.104,0.156 10 2 1.094,0.396 1.198,0.552 0.104,0.156 10 5 0.844,1.667 0.948,1.823 0.104,0.156 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the EV water pump relay (INV W/PMP).


Hide G9230A 4.INSPECT BATTERY FAN RELAY (BATT FAN)

a.
E222294N64
1.073,0.958 1.302,0.49 1.302,0.49 1.438,0.49 false 1.063,1.333 1.146,1.75 1.146,1.75 1.344,1.75 false 0.802,1.01 0.938,0.49 0.938,0.49 1.063,0.49 false 0.563,1.281 0.635,1.76 0.635,1.76 0.823,1.76 false 1.458,0.406 1.563,0.563 0.104,0.156 10 1 1.375,1.667 1.479,1.823 0.104,0.156 10 2 1.094,0.396 1.198,0.552 0.104,0.156 10 5 0.844,1.667 0.948,1.823 0.104,0.156 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No.1 battery fan relay (BATT FAN).