Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › PATTERN SELECT SWITCH
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0457191 PATTERN SELECT SWITCH G

HYBRID / BATTERY CONTROL  PATTERN SELECT SWITCH  INSPECTION  


PROCEDURE

Hide 84720A 1.INSPECT NO. 1 PATTERN SELECT SWITCH ASSEMBLY (DRIVE MODE)

a.
C444793C03
1.542,0.229 1.906,0.438 0.365,0.208 0.938,1.865 1.177,1.865 1.177,1.865 1.573,1.323 true 1.813,1.844 1.813,1.333 true 2.24,1.313 2.552,1.885 2.552,1.885 2.781,1.885 true 0.063,0.052 0.344,0.292 0.281,0.24 10 false *a 2.823,1.813 3.25,2.031 0.427,0.219 10 false DMS+ 0.542,1.802 0.948,2 0.406,0.198 10 false DMS- 1.792,1.875 1.99,2.104 0.198,0.229 10 false E 1.635,0.25 1.917,0.438 0.281,0.188 10 false D5
*a Component without harness connected
(No. 1 Pattern Select Switch Assembly (DRIVE MODE))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D5)Location & Routing

Click Connector(D5)Instrument Panel>Instrument Panel Wire>No. 1 Pattern Select Switch Assembly

D5-1 (DMS+) - D5-3 (E) When the DRIVE MODE switch is operated and held on the top side Below 10 Ω
D5-1 (DMS+) - D5-3 (E)
D5-4 (DMS-) - D5-3 (E)
When the DRIVE MODE switch is not operated 10 kΩ or higher
D5-4 (DMS-) - D5-3 (E) When the DRIVE MODE switch is operated and held on the bottom side Below 10 Ω


If the result is not as specified, replace the No. 1 pattern select switch assembly (DRIVE MODE).


b.
C444793C04
1.531,0.198 1.917,0.406 0.385,0.208 1.021,1.865 1.229,1.865 1.229,1.865 1.427,1.323 true 2.5,1.885 2.208,1.885 2.208,1.885 2.021,1.323 true 0.063,0.052 0.344,0.292 0.281,0.24 10 false *a 0.719,1.802 1.052,2 0.333,0.198 10 false ILL+ 2.542,1.813 2.927,2.01 0.385,0.198 10 false ILL- 1.635,0.219 1.917,0.438 0.281,0.219 10 false D5
*a Component without harness connected
(No. 1 Pattern Select Switch Assembly (DRIVE MODE))


Apply battery voltage between the terminals of the No. 1 pattern select switch assembly (DRIVE MODE), and check the illumination condition of the No. 1 pattern select switch assembly (DRIVE MODE).

Standard:
Measurement Condition Specified Condition
Battery positive (+) → D5-5 (ILL+)
Battery negative (-) → D5-2 (ILL-)
Illuminates


If the result is not as specified, replace the No. 1 pattern select switch assembly (DRIVE MODE).