Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  U011000  Lost Communication with Drive Motor Control Module "A"  U012987  Lost Communication with Brake System Control Module "A" Missing Message  U029300  Lost Communication with Hybrid/EV Powertrain Control Module  U110600  Lost Communication with Electric Parking Brake Module  U115000  Lost Communication with Hybrid Powertrain Control Module (ch2)  U117D87  Lost Communication with Brake System Control Module (ch4) Missing Message  U149257  Software incompatibility with Hybrid/EV Powertrain Control Module Invalid/Incompatible Software Component  


DESCRIPTION

The No. 1 skid control ECU (brake booster with master cylinder assembly) receives signals from the EV control ECU, inverter with converter assembly and No. 2 skid control ECU (brake actuator assembly) via CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
U011000 Lost Communication with Drive Motor Control Module "A" When terminal IG2 voltage is 9.5 V or more, data from the inverter with converter assembly cannot be received for 2 seconds or more.
·

CAN communication line

·

Inverter with converter assembly

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
U012987 Lost Communication with Brake System Control Module "A" Missing Message When the voltage at terminal IG1 is 9.5 V or more, communication between the No. 1 skid control ECU (brake booster with master cylinder assembly) and No. 2 skid control ECU (brake actuator assembly) is not possible for 2 seconds or more.
·

CAN communication line

·

No. 2 skid control ECU (brake actuator assembly)

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
U029300 Lost Communication with Hybrid/EV Powertrain Control Module When terminal IG2 voltage is 9.5 V or more, data from the EV control ECU cannot be received for 2 seconds or more.
·

CAN communication line

·

EV control ECU

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
U110600 Lost Communication with Electric Parking Brake Module With terminal IG1 voltage at 9.5 V or more, data cannot be received from the No. 2 skid control ECU (brake actuator assembly) for 1 second or more.
·

CAN communication line

·

No. 2 skid control ECU (brake actuator assembly)

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
U115000 Lost Communication with Hybrid Powertrain Control Module (ch2) When terminal IG2 voltage is 9.5 V or more, data from the EV control ECU cannot be received for 2 seconds or more.
·

CAN communication line

·

EV control ECU

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
U117D87 Lost Communication with Brake System Control Module (ch4) Missing Message When the voltage at terminal IG1 is 9.5 V or more, communication between the No. 1 skid control ECU (brake booster with master cylinder assembly) and No. 2 skid control ECU (brake actuator assembly) is not possible for 2 seconds or more.
·

CAN communication line

·

No. 2 skid control ECU (brake actuator assembly)

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
U149257 Software incompatibility with Hybrid/EV Powertrain Control Module Invalid/Incompatible Software Component Either of the following is detected:
·

The engine type, powertrain variation and destination information sent from the EV control ECU do not match the information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly).

·

No system information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly).


·

CAN communication line

·

EV control ECU

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

U149257 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status The engine type, powertrain variation and destination information sent from the EV control ECU do not match the information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly) ○ -
No system information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly) - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


PROCEDURE

1.CHECK DTC (HEALTH CHECK)
a.

Perform the Health Check using the GTS.


Result:
Result Proceed to
DTCs for related systems are output together with DTC U011000, U012987, U029300, U110600, U115000, U117D87 or U149257. A
DTC U011000, U012987, U029300, U110600, U115000, U117D87 or U149257 is output. B
DTCs are not output. C



A

GO TO DIAGNOSTIC TROUBLE CODE CHART (RELATED SYSTEM)

B

C