Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  U011087  Lost Communication with Drive Motor Control Module "A" Missing Message  U012587  Lost Communication with Multi-axis Acceleration Sensor Module Missing Message  U012687  Lost Communication with Steering Angle Sensor Module Missing Message  U014087  Lost Communication with Body Control Module Missing Message  U015187  Lost Communication with Restraints Control Module Missing Message  U025E87  Lost Communication with Electronic Brake Booster Control Module "A" Missing Message  U029387  Lost Communication with Hybrid/EV Powertrain Control Module Missing Message  U110787  Lost Communication with Power Management Module Missing Message  U115087  Lost Communication with Hybrid Powertrain Control Module (ch2) Missing Message  U115987  Lost Communication with Electronic Brake Booster Control Module "A" (ch3) Missing Message  U130857  Software Incompatibility with Pre-collision Control Module Invalid / Incompatible Software Component  


DESCRIPTION

The airbag ECU assembly has a built-in yaw rate and acceleration sensor.

The No. 2 skid control ECU (brake actuator assembly) receives signals from the EV control ECU, steering sensor, certification ECU (smart key ECU assembly), inverter with converter assembly, No. 1 skid control ECU (brake booster with master cylinder assembly), airbag ECU assembly, yaw rate and acceleration sensor (airbag ECU assembly), forward recognition camera*1 or object recognition camera*2 and main body ECU (multiplex network body ECU) via CAN communication.

*1: Mono Camera Type

*2: Stereo Camera Type


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
U011087 Lost Communication with Drive Motor Control Module "A" Missing Message When terminal IG1 voltage is 10 V or more and IGP_PT2 signal is on, data cannot be received from the inverter with converter assembly for 2 seconds or more.
·

CAN communication line

·

Inverter with converter assembly

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message When the +BS terminal voltage is between 9.5 and 17.4 V, data from the acceleration sensor cannot be received for 1 second or more.
·

CAN communication line

·

Acceleration sensor (airbag ECU assembly)

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
U012687 Lost Communication with Steering Angle Sensor Module Missing Message When the +BS terminal voltage is between 9.5 and 17.4 V, data from the steering sensor cannot be received for 1 second or more.
·

CAN communication line

·

Steering sensor

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
U014087 Lost Communication with Body Control Module Missing Message When the voltage at terminal IG1 is 10 V or more, data from the main body ECU (multiplex network body ECU) cannot be received for 2 seconds or more.
·

CAN communication line

·

Main body ECU (multiplex network body ECU)

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
U015187 Lost Communication with Restraints Control Module Missing Message When the +BS terminal voltage is between 9.5 and 17.4 V and the vehicle speed exceeds 7 km/h (4 mph), data cannot be received from the airbag ECU assembly for 5 seconds or more.
·

CAN communication line

·

Airbag ECU assembly

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
U025E87 Lost Communication with Electronic Brake Booster Control Module "A" Missing Message When the voltage at terminal IG1 is 10 V or more, communication between the No. 1 skid control ECU (brake booster with master cylinder assembly) and No. 2 skid control ECU (brake actuator assembly) is not possible for 2 seconds or more.
·

CAN communication line

·

No. 1 skid control ECU (brake booster with master cylinder assembly)

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message When terminal IG1 voltage is 10 V or more and IGP_PT2 signal is on, data from the EV control ECU cannot be received for 2 seconds or more.
·

CAN communication line

·

EV control ECU

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
U110787 Lost Communication with Power Management Module Missing Message When the voltage at terminal IG1 is 10 V or more, the certification ECU (smart key ECU assembly) cannot communicate for 3 seconds or more.
·

CAN communication line

·

Certification ECU (smart key ECU assembly)

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
U115087 Lost Communication with Hybrid Powertrain Control Module (ch2) Missing Message When terminal IG1 voltage is 10 V or more and IGP_PT2 signal is on, data from the EV control ECU cannot be received for 2 seconds or more.
·

CAN communication line

·

EV control ECU

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
U115987 Lost Communication with Electronic Brake Booster Control Module "A" (ch3) Missing Message When the voltage at terminal IG1 is 10 V or more, communication between the No. 1 skid control ECU (brake booster with master cylinder assembly) and No. 2 skid control ECU (brake actuator assembly) is not possible for 2 seconds or more.
·

CAN communication line

·

No. 1 skid control ECU (brake booster with master cylinder assembly)

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)
U130857 Software Incompatibility with Pre-collision Control Module Invalid / Incompatible Software Component Either of the following is detected:
·

The variation and destination information sent from the forward recognition camera do not match the information stored in the No. 2 skid control ECU (brake actuator assembly).*1

·

The variation and destination information sent from the object recognition camera do not match the information stored in the No. 2 skid control ECU (brake actuator assembly).*2

·

No system information stored in the No. 2 skid control ECU (brake actuator assembly).


·

CAN communication line

·

Forward recognition camera*1

·

Object recognition camera*2

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake/EPB B Output ECU: No. 2 skid control ECU (brake actuator assembly)

*1: Mono Camera Type

*2: Stereo Camera Type


U130857 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status The variation and destination information sent from the forward recognition camera do not match the information stored in the No. 2 skid control ECU (brake actuator assembly)*1 ○ - -
The variation and destination information sent from the object recognition camera do not match the information stored in the No. 2 skid control ECU (brake actuator assembly)*2 - ○ -
No system information stored in the No. 2 skid control ECU (brake actuator assembly) - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

*1: Mono Camera Type

*2: Stereo Camera Type


HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


PROCEDURE

1.CHECK DTC (HEALTH CHECK)
a.

Perform the Health Check using the GTS.


Result:
Result Proceed to
DTCs for related systems are output together with U011087, U012587, U012687, U014087, U015187, U025E87, U029387, U110787, U115087, U115987 or U130857. A
DTC U011087, U012587, U012687, U014087, U015187, U025E87, U029387, U110787, U115087, U115987 or U130857 is output. B
DTCs are not output. C



A

GO TO DIAGNOSTIC TROUBLE CODE CHART (RELATED SYSTEM)

B

C