CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector and measure the voltage or resistance on the wire harness side.
| *a | Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
- | - |
The voltage cannot be measured with the connector connected to the No. 1 skid control ECU (brake booster with master cylinder assembly) as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A5-1 (MRI1) - Body ground | Brake booster with accumulator pump assembly power supply input | Always | 11 to 14 V |
| A5-2 (MGND) - Body ground | Brake booster with accumulator pump assembly ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A5-3 (SKS1) | Brake pedal stroke sensor 1 signal input | - | - |
| A5-4 | - | - | - |
| A5-5 | - | - | - |
| A5-6 | - | - | - |
| A5-7 | - | - | - |
| A5-8 | - | - | - |
| A5-9 | - | - | - |
| A5-10 | - | - | - |
| A5-11 | - | - | - |
| A5-12 (LBL) | Brake fluid level warning switch (Brake booster with master cylinder assembly) input | - | - |
| A5-13 | - | - | - |
| A5-14 (+BI1) - Body ground | +BI1 power source input | Always | 11 to 14 V |
| A5-15 (BS) - Body ground | Solenoid power supply input | Always | 11 to 14 V |
| A5-16 (VSK1) | Brake pedal stroke sensor 1 power supply output | - | - |
| A5-17 | - | - | - |
| A5-18 (SKG1) | Brake pedal stroke sensor 1 ground | - | - |
| A5-19 | - | - | - |
| A5-20 | - | - | - |
| A5-21 | - | - | - |
| A5-22 | - | - | - |
| A5-23 | - | - | - |
| A5-24 | - | - | - |
| A5-25 (EXO) | No. 2 skid control ECU (brake actuator assembly) operation signal output | - | - |
| A5-26 | - | - | - |
| A5-27 | - | - | - |
| A5-28 (GND1) - Body ground | No. 1 skid control ECU (Brake booster with master cylinder assembly) ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A5-29 (M+) | Brake booster with accumulator pump assembly power supply (+) | - | - |
| A5-30 (M-) | Brake booster with accumulator pump assembly power supply (-) | - | - |
| A5-31 (IG1) - Body ground | IG1 power source input | Ignition switch ON | 11 to 14 V |
| A5-32 | - | - | - |
| A5-33 | - | - | - |
| A5-34 | - | - | - |
| A5-35 (CA2H) | CAN communication line 2 (H) | - | - |
| A5-36 (CA2L) | CAN communication line 2 (L) | - | - |
| A5-37 (STP) - Body ground | Stop light switch assembly input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| A5-38 (CA1H) | CAN communication line 1 (H) | - | - |
| A5-39 (CA1L) | CAN communication line 1 (L) | - | - |
| A5-40 (CTY) - Body ground | Front door courtesy light switch assembly input (for driver side) | Driver door closed → open | 11 to 14 V → Below 1.5 V |
| A5-41 | - | - | - |
| A5-42 (IG2) - Body ground | IG2 power source input | Ignition switch ON | 11 to 14 V |
CHECK BRAKE ACTUATOR ASSEMBLY
Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector and measure the voltage or resistance on the wire harness side.
| *a | Front view of wire harness connector
(to No. 2 Skid Control ECU (brake actuator assembly)) |
- | - |
The voltage cannot be measured with the connector connected to the No. 2 skid control ECU (brake actuator assembly) as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A6-1 (GND1) - Body ground | No. 2 skid control ECU (brake actuator assembly) ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A6-2 | - | - | - |
| A6-3 | - | - | - |
| A6-4 (RL-) | Rear speed sensor LH (-) signal input | - | - |
| A6-5 (RL+) | Rear speed sensor LH (+) power supply output | - | - |
| A6-6 (FR-) | Front speed sensor RH (-) signal input | - | - |
| A6-7 (FR+) | Front speed sensor RH (+) power supply output | - | - |
| A6-8 (TSEN) | - | - | - |
| A6-9 (CSW) - Body ground | VSC OFF switch input | VSC OFF switch is pushed → released | Below 1 Ω → 10 kΩ or higher |
| A6-10 (SKS2) | Brake pedal stroke sensor 2 signal input | - | - |
| A6-11 (STP) - Body ground | Stop light switch assembly input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| A6-12 | - | - | - |
| A6-13 | - | - | - |
| A6-14 (+BS) - Body ground | ABS solenoid relay power supply input | Always | 11 to 14 V |
| A6-15 (IG2) - Body ground | IG2 power source input | Ignition switch ON | 11 to 14 V |
| A6-16 (CA2H) | CAN communication line 2 (H) | - | - |
| A6-17 (CA2L) | CAN communication line 2 (L) | - | - |
| A6-18 (SP1) | Speed sensor signal output | - | - |
| A6-19 (RR-) | Rear speed sensor RH (-) signal input | - | - |
| A6-20 (RR+) | Rear speed sensor RH (+) power supply output | - | - |
| A6-21 (FL-) | Front speed sensor LH (-) signal input | - | - |
| A6-22 (FL+) | Front speed sensor LH (+) power supply output | - | - |
| A6-23 | - | - | - |
| A6-24 | - | - | - |
| A6-25 (VSK2) | Brake pedal stroke sensor 2 power supply output | - | - |
| A6-26 (SKG2) | Brake pedal stroke sensor 2 ground | - | - |
| A6-27 (CANH) | CAN communication line (H) | - | - |
| A6-28 (CA3H) | CAN communication line 3 (H) | - | - |
| A6-29 (CTY) - Body ground | No. 2 Skid control ECU (brake actuator assembly) operation signal input | Ignition switch ON | 11 to 14 V |
| A6-30 (GND2) - Body ground | ABS motor ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A6-31 | - | - | - |
| A6-32 (STPO) - Body ground | Stop light control relay (No. 2 semiconductor power integration ECU) output | Always | 11 to 14 V |
| A6-33 | - | - | - |
| A6-34 | - | - | - |
| A6-35 (PKB) - Body ground | Brake hold switch (electric parking brake switch assembly) input | Brake hold switch (electric parking brake switch assembly) is pushed → released | Below 1 Ω → 10 kΩ or higher |
| A6-36 | - | - | - |
| A6-37 (STP2) - Body ground | Stop light control relay (No. 2 semiconductor power integration ECU) input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| A6-38 | - | - | - |
| A6-39 | - | - | - |
| A6-40 | - | - | - |
| A6-41 | - | - | - |
| A6-42 | - | - | - |
| A6-43 (CANL) | CAN communication line (L) | - | - |
| A6-44 (CA3L) | CAN communication line 3 (L) | - | - |
| A6-45 (IG1) - Body ground | IG1 power source input | Ignition switch ON | 11 to 14 V |
| A6-46 (BM) - Body ground | ABS motor relay power supply input | Always | 11 to 14 V |
TERMINALS OF ECU (STEERING SENSOR)
| *a | Component without harness connected (Steering Sensor) | - | - |
| Terminal No. (Symbol) | Terminal Description |
|---|---|
| 1 | - (Not used) |
| 2 (2S) | Wiper motor operation signal |
| 3 (CANH) | CAN communication line H |
| 4 (BAT) | ECU power supply input |
| 5 | - (Not used) |
| 6 (ESS) | Body ground |
| 7 (HEAD) | Headlight operation signal |
| 8 (CANL) | CAN communication line L |
| 9 (IG1) | IG1 power source input |
| 10 | - (Not used) |
TERMINAL INSPECTION (STEERING SENSOR)
Disconnect the D34 connector and measure the voltage or resistance on the wire harness side.
| *a | Front view of wire harness connector
(to Steering Sensor) |
- | - |
Voltage cannot be measured with the connector connected to the steering sensor as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| D34-4 (BAT) - Body ground | ECU power supply output | Always | 11 to 14 V |
| D34-6 (ESS) - Body ground | Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| D34-9 (IG1) - Body ground | IG1 power source input | Ignition switch ON | 11 to 14 V |