Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0455059 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Telephone microphone assembly

·

Radio and display receiver assembly

·

Harness or connector


Navigation System A

WIRING DIAGRAM

E461113E01
0.813,2.74 2.198,3.115 1.385,0.375 10 false Telephone Microphone Assembly 0.813,2.573 1.125,2.75 0.313,0.177 10 false H17 5.344,2.781 7.031,3.271 1.688,0.49 10 false Radio and Display Receiver Assembly 5.365,2.583 5.708,2.76 0.344,0.177 10 false D56 5.75,1.031 6.188,1.198 0.438,0.167 10 false SNS2 5.479,0.948 5.729,1.115 0.25,0.167 10 false 25 1.323,1.042 1.76,1.208 0.438,0.167 10 false SNS2 1.792,0.958 1.958,1.135 0.167,0.177 10 false 3 1.333,1.979 1.771,2.146 0.438,0.167 10 false MCO- 1.813,1.896 1.979,2.073 0.167,0.177 10 false 4 5.51,1.896 5.76,2.063 0.25,0.167 10 false 22 5.76,1.969 6.104,2.146 0.344,0.177 10 false MIN-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

Pre-procedure1

a.

Disconnect the D56 radio and display receiver assembly connector.


b.

Disconnect the H17 telephone microphone assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D56,H17)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assembly

D56-25 (SNS2) - H17-3 (SNS2) Always Below 1 Ω
D56-22 (MIN-) - H17-4 (MCO-) Always Below 1 Ω
D56-25 (SNS2) - Body ground Always 10 kΩ or higher
D56-22 (MIN-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.INSPECT TELEPHONE MICROPHONE ASSEMBLY (SNS2, MCO-)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT TELEPHONE MICROPHONE ASSEMBLY (SNS2, MCO-)

Pre-procedure1

a.

Remove the telephone microphone assembly.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL



Procedure1

b.
E364293N01
1.76,1.229 2.01,0.458 2.01,0.458 2.198,0.458 true 1.458,1.229 1.188,0.469 1.188,0.469 0.958,0.469 true 2.26,0.385 2.698,0.552 0.438,0.167 10 false SNS2 0.542,0.375 0.958,0.552 0.417,0.177 10 false MCO-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SNS2) - 4 (MCO-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG