Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0455059 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Microphone Circuit  


DESCRIPTION

The radio and display receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM


E460015E01
1.5,0.698 1.938,0.885 0.438,0.188 10 false SNS2 1.469,1.188 1.927,1.365 0.458,0.177 10 false MACC 1.479,1.75 1.885,1.948 0.406,0.198 10 false MCO- 1.479,2.292 1.927,2.49 0.448,0.198 10 false MCO+ 0.354,2.74 0.813,2.938 0.458,0.198 10 false H17 0.354,2.917 2.479,3.135 2.125,0.219 10 false Telephone Microphone Assembly 1.99,0.604 2.146,0.802 0.156,0.198 10 false 3 1.979,1.094 2.167,1.302 0.188,0.208 10 false 1 1.979,1.635 2.198,1.833 0.219,0.198 10 false 4 1.958,2.198 2.177,2.396 0.219,0.198 10 false 2 5.688,0.594 5.906,0.792 0.219,0.198 10 false 25 5.677,2.198 5.896,2.396 0.219,0.198 10 false 21 5.667,1.635 5.885,1.833 0.219,0.198 10 false 22 5.688,2.75 5.906,2.948 0.219,0.198 10 false 24 5.948,0.698 6.396,0.875 0.448,0.177 10 false SNS2 5.958,2.302 6.385,2.49 0.427,0.188 10 false MIN+ 5.958,1.75 6.406,1.938 0.448,0.188 10 false MIN- 5.948,2.865 6.396,3.052 0.448,0.188 10 false SGND 5.458,3.156 5.823,3.333 0.365,0.177 10 false D56 5.448,3.313 7.156,3.708 1.708,0.396 10 false Radio and Display Receiver Assembly 5.948,1.198 6.427,1.385 0.479,0.188 10 false MACC 5.667,1.073 5.885,1.26 0.219,0.188 10 false 23 3.844,2.594 4,2.792 0.156,0.198 10 false * 0.188,3.417 0.927,3.604 0.74,0.188 10 false *: Shielded

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the D56 radio and display receiver assembly connector.


b.

Disconnect the H17 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D56,H17)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assembly

D56-25 (SNS2) - H17-3 (SNS2) Always Below 1 Ω
D56-23 (MACC) - H17-1 (MACC) Always Below 1 Ω
D56-22 (MIN-) - H17-4 (MCO-) Always Below 1 Ω
D56-21 (MIN+) - H17-2 (MCO+) Always Below 1 Ω
D56-25 (SNS2) - Body ground Always 10 kΩ or higher
D56-23 (MACC) - Body ground Always 10 kΩ or higher
D56-22 (MIN-) - Body ground Always 10 kΩ or higher
D56-21 (MIN+) - Body ground Always 10 kΩ or higher
D56-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E460016C01
1.5,0.75 1.917,1 0.417,0.25 2.813,2.604 2.052,2.156 true 2.271,2.896 1.927,2.156 true 1.198,2.833 1.813,2.146 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.594,0.792 1.906,0.99 0.313,0.198 10 false D56 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN- 2.083,2.896 2.583,3.115 0.5,0.219 10 false MACC 1.01,2.854 1.625,3.052 0.615,0.198 10 false SGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D56)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D56-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D56)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D56-24 (SGND) - Body ground Always Below 1 Ω
D56-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
E364295C98
1.5,0.313 1.906,0.573 0.406,0.26 1.063,0.542 1.25,0.542 1.25,0.542 1.448,1.24 true 2.365,0.552 2.177,0.552 2.177,0.552 1.938,1.229 true 0.365,0.448 0.677,0.646 0.313,0.198 10 false *a 2.833,3.448 3.292,3.646 0.458,0.198 10 false GND 1.594,0.365 1.906,0.563 0.313,0.198 10 false H17 0.625,0.448 1.24,0.646 0.615,0.198 10 false MCO- 2.448,0.469 3.063,0.667 0.615,0.198 10 false MCO+
*a Component with harness connected
(Telephone Microphone Assembly)


a.

Check the output waveform.

i.

Remove the telephone microphone assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


ii.

Connect an oscilloscope to terminal H17-2 (MCO+) and H17-4 (MCO-).


iii.

Turn the ignition switch to ON.


iv.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case LH.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H17-2 (MCO+) - H17-4 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Ignition switch ON

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case LH.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG