Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0453477 HYBRID BATTERY SYSTEM D

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  UTILITY  


NOTICE:
·

If the EV supply battery assembly or an EV supply stack sub-assembly has been replaced, make sure to perform the following utilities in the following order: "Battery Status Info Update", "Prediagnostic Battery Charge" then "Battery Diagnosis".

·

"Maintenance Required for Traction Battery at Your Dealer" is displayed, perform both "Prediagnostic Battery Charge" and "Battery Diagnosis" to diagnose the extent of deterioration of each EV battery cell.

·

"Maintenance Required for Traction Battery at Your Dealer" is cleared after both "Prediagnostic Battery Charge" and "Battery Diagnosis" are performed and "There is no need to replace HV battery." is displayed.

·

After the "Maintenance Required for Traction Battery at Your Dealer" is displayed, if the traction battery is used continually without performing "Prediagnostic Battery Charge" and "Battery Diagnosis" for a few weeks*, use of the EV supply battery assembly (input/output voltage) will be limited. If it is used more, the ignition switch ON (READY) operation will be disabled.

*: Timing may vary depending on vehicle usage.

·

If the ignition switch cannot be turned to ON (READY), perform "Temporary Vehicle Start Up", "Prediagnostic Battery Charge" and "Battery Diagnosis".



HINT:

If "Maintenance Required for Traction Battery at Your Dealer" is displayed, Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>"HAVE TRACTION BATTERY INSPECTED" is displayed.


Purpose


Utility Items
(GTS Display)
Main Purpose Control Description
All Readiness Check whether or not DTC judgment has been completed. -
Diagnosis Related Information Confirm the diagnosis related information. -
Prediagnostic Battery Charge Before performing "Battery Diagnosis", charge the EV supply battery assembly, as a high SOC of the EV supply battery assembly is required to start "Battery Diagnosis". Forced charging of EV supply battery assembly
Battery Diagnosis Discharge the EV supply battery assembly and diagnose the extent of deterioration of each EV supply stock sub-assembly based on the SOC. Forced discharging of EV supply battery assembly
Battery Status Info Update Initialize the EV battery age information. -
Temporary Vehicle Start Up - Temporarily enable the ignition switch ON (READY) operation which has been disabled due to continual usage of the vehicle without performing battery diagnosis.
High Voltage Fuse Accumulated Load History Reset Initialize the load history of the high voltage fuse. -


ALL READINESS


HINT:
·

With "All Readiness", you can check whether or not the DTC judgment has been completed by using the GTS.

·

You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs even if no DTCs are stored.


e.

Turn the ignition switch off and wait for at least 10 minutes.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Perform the DTC judgment driving pattern to run the DTC judgment.


i.

Enter the following menus: Powertrain / EV Battery / Utility / All Readiness.

Powertrain > EV Battery > Utility
Tester Display
All Readiness
50005 398 20

j.

Input the DTCs to be confirmed.


k.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform the driving pattern




l.

Turn the ignition switch off.



DIAGNOSIS RELATED INFORMATION


a.

Check for diagnosis related information.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / EV Battery / Utility / Diagnosis Related Information.

Powertrain > EV Battery > Utility
Tester Display
Diagnosis Related Information
50005 398 56

v.

Check the Diagnosis Related Information, and then write them down.



b.

Clear diagnosis related information.

NOTICE:

Clearing the DTCs will also clear the diagnosis related information.


i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / EV Battery / Trouble Codes.

Powertrain > EV Battery > Clear DTCs
50002 398

v.

Clear the DTCs.


vi.

Turn the ignition switch off.




BATTERY STATUS INFO UPDATE


HINT:

If the EV supply battery assembly or an EV supply stack sub-assembly has been replaced, make sure to perform "Battery Status Info Update" to initialize the EV battery age information stored in the battery ECU assembly and turn off the light on the combination meter assembly.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Powertrain / EV Battery / Utility / Battery Status Info Update.

Powertrain > EV Battery > Utility
Tester Display
Battery Status Info Update
50005 398 4224

d.

Turn the ignition switch off.



PREDIAGNOSTIC BATTERY CHARGE


NOTICE:
·

If the fuel level warning light is illuminated, add enough fuel that the light turns off, and then perform "Prediagnostic Battery Charge".

·

Perform EV battery charging with appropriate EV battery temperature, between 0°C (32°F) and 47°C (116.6°F).

·

Do not perform prediagnostic battery charge while the master warning is illuminated.

·

Perform prediagnostic battery charge with the EV supply battery assembly installed correctly.

·

Do not perform prediagnostic battery charge while changing from inspection mode to another mode.



HINT:
·

If the EV battery temperature is low (below 0°C (32°F)), drive the vehicle until the temperature reaches 0°C (32°F) or higher and perform "Prediagnostic Battery Charge" again.

·

If the EV battery temperature is high (above 47°C (116.6°F)), leave the vehicle with the ignition switch ON (READY) and park (P) selected. Wait until the EV battery temperature drops to 42°C (107.6°F) or less, and then perform "Prediagnostic Battery Charge" again.

·

If the EV battery temperature is low (below 0°C (32°F)) and the ignition switch cannot be turned to ON (READY), place the vehicle in a warm environment (20°C (68°F) or higher). Wait until the EV battery temperature reaches 10°C (50°F) or higher, and then perform "Prediagnostic Battery Charge" again.



a.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / EV Battery / Utility / Prediagnostic Battery Charge.

Powertrain > EV Battery > Utility
Tester Display
Prediagnostic Battery Charge
50005 398 4181

v.

Check items on the display and press "Next".


vi.

When the prediagnostic battery charge is suspended because the charging conditions are not met anymore, the reasons for suspension are displayed on the GTS. Perform "Prediagnostic Battery Charge" after checking the causes and troubleshoot the suspected area in accordance with instructions in the "Procedure when prediagnostic battery charge is suspended" table.

Procedure when prediagnostic battery charge is suspended
GTS Display Reason for Charging Suspension
(Related Condition)
Procedure
105 Unable to complete the current sensor offset learning Turn the ignition switch off and then perform "Prediagnostic Battery Charge" again.
(If trouble code 105 is output again, inspect the current sensor.)
(Click here)
107 EV supply battery assembly connection malfunction Confirm the connection condition of the EV supply battery assembly.
108 Shift state park (P) is not selected. Press the P position switch (parking switch) to select park (P).
110 Current out of the specified range
(-60 to 25 A)
If accessories are connected to the vehicle, turn them off or disconnect them from the vehicle.
111 Battery temperature out of the specified range
(0°C (32°F) to 47°C (116.6°F))
Read the temperatures listed in "Hybrid/EV Battery Temperature 1-6".
·

When the EV battery temperature is below 0°C (32°F): Drive the vehicle until the temperature reaches 0°C (32°F) or higher.

·

When the EV battery temperature is above 47°C (116.6°F): Leave the vehicle with the ignition switch ON (READY) and park (P) selected and wait until the EV battery temperature drops to 42°C (107.6°F) or less.


112 Excessive charge Check "Hybrid/EV Battery SOC" listed in the Data List.
·

When the SOC is below 74%: Turn the ignition switch off and perform "Prediagnostic Battery Charge" again.

·

When the SOC is 74% or more: Cancel "Prediagnostic Battery Charge" and perform "Battery Diagnosis" again.


113 Excessive voltage Cancel "Prediagnostic Battery Charge" and perform "Battery Diagnosis" again.
115 Time-out If the ignition switch is turned off by the time-out function, perform "Prediagnostic Battery Charge" again.
116 EV battery malfunction
·

Check for HV battery system related DTCs and perform troubleshooting.

·

After checking that the master warning has turned off, perform "Prediagnostic Battery Charge" again.


117 System malfunction
118 Low auxiliary battery voltage Inspect the auxiliary battery and DC/DC converter function.
(Click here)
Communication error or 109 The ignition switch was turned off or a GTS communication error occurred. After checking that the connector of the GTS is not disconnected from the DLC3, perform "Prediagnostic Battery Charge" again.


vii.

The screen transitions to the next screen and "Turn the ignition switch to ON (READY)" is displayed.


viii.

While depressing the brake pedal, turn the ignition switch to ON (READY).

HINT:

The FC system starts without the READY indicator illuminated.



ix.

The screen transitions to the next screen and "Charging the battery." is displayed.

NOTICE:

If a DTC is stored during "Prediagnostic Battery Charge", the master warning will turn on and stop the charging.


HINT:
·

Time required for "Prediagnostic Battery Charge" varies by the SOC of the EV supply battery assembly when the charging is started.

·

To suspend prediagnostic battery charge, press "Exit" and turn the ignition switch off.




x.

When the prediagnostic battery charge is suspended because the charging conditions are not met anymore, the reasons of suspension are displayed on the GTS. Perform "Battery Diagnosis" after checking the causes and troubleshoot the suspected area in accordance with instructions in the "Procedure when prediagnostic battery charge is suspended" table.


xi.

The FC system stops when "Prediagnostic Battery Charge" is complete.


xii.

The screen transitions to the next screen and "Prediagnostic Battery Charge is complete." is displayed.


xiii.

Press "Exit" and turn the ignition switch off.



b.

When not using the GTS:

i.

Perform the following procedure within 60 seconds of the ignition switch being turned to ON.

1.

Check that park (P) is selected. (Do not depress the accelerator pedal.)

2.

While depressing the brake pedal with your left foot, move the shift lever to select neutral (N) and fully depress the accelerator pedal three times with your right foot.

3.

Press the P position switch to select park (P), and then fully depress the accelerator pedal twice.

4.

While depressing the brake pedal with your left foot, move the shift lever to select neutral (N) and fully depress the accelerator pedal three times with your right foot.

5.

Press the P position switch to select park (P), and then fully depress the accelerator pedal twice.


HINT:

Fully depressing the accelerator pedal from the closed position is counted as one operation.



ii.

Wait for 5 seconds.


iii.

While depressing the brake pedal, turn the ignition switch to ON (READY).

HINT:
·

The FC system starts without the READY indicator illuminated.

·

If the SOC indicator of the EV battery shows 6 segments or more, charging of the vehicle is not necessary. Therefore, the FC system will not start. In this case, perform "Battery Diagnosis".




iv.

Wait until the FC system stops.

NOTICE:

If a DTC is stored during "Prediagnostic Battery Charge", the master warning will turn on and stop the charging.


HINT:
·

Time required for "Prediagnostic Battery Charge" varies by the SOC of the EV supply battery assembly when the charging is started.

·

To suspend prediagnostic battery charge, turn the ignition switch off.




v.

The FC system stops when "Prediagnostic Battery Charge" is complete.

HINT:

If "Prediagnostic Battery Charge" completes correctly, the SOC indicator of the EV battery will show 6 segments or more.



vi.

Turn the ignition switch off.




BATTERY DIAGNOSIS


NOTICE:
·

Perform EV battery diagnosis with appropriate EV battery temperature (between 0°C (32°F) and 47°C (116.6°F)).

·

Do not perform battery diagnosis while the master warning is illuminated.

·

Perform battery diagnosis with the EV supply battery assembly installed correctly.

·

Do not perform battery diagnosis while changing from inspection mode to another mode.

·

Make sure to turn the ignition switch off after battery diagnosis to prevent the auxiliary battery from being discharged.



HINT:
·

If the EV battery temperature is low (below 0°C (32°F)), drive the vehicle until the temperature reaches 0°C (32°F) or higher and perform "Battery Diagnosis" again.

·

If the EV battery temperature is high (above 47°C (116.6°F)), leave the vehicle with the ignition switch ON (READY) and park (P) selected. Wait until the EV battery temperature drops to 42°C (107.6°F) or less, and then perform "Battery Diagnosis" again.

·

If the EV battery temperature is low (below 0°C (32°F)) and the ignition switch cannot be turned to ON (READY), place the vehicle in a warm environment (20°C (68°F) or higher). Wait until the EV battery temperature reaches 0°C (32°F) or higher, and then perform "Battery Diagnosis" again.



a.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Enter the following menus: Powertrain / EV Battery / Utility / Battery Diagnosis.

Powertrain > EV Battery > Utility
Tester Display
Battery Diagnosis
50005 398 4182

iv.

Check items on the display and press "Next".


v.

When the battery diagnosis is suspended because the diagnosis conditions are not met anymore, the reasons for suspension are displayed on the GTS. Perform "Battery Diagnosis" after checking the causes and troubleshoot the suspected area in accordance with instructions in the "Procedure when battery diagnosis is suspended" table.

Procedure when battery diagnostic is suspended
GTS Display Reason for Diagnosis Suspension
(Related Condition)
Procedure
004 Voltage too low Turn the ignition switch off and then perform "Prediagnostic Battery Charge" again.
005 Unable to complete the current sensor offset learning Turn the ignition switch off and then perform "Battery Diagnosis" again.
(If trouble code 005 is output again, inspect the current sensor.)
(Click here)
006 The ignition switch was turned off. Turn the ignition switch off and after checking that the connector of the GTS is not disconnected from the DLC3, perform "Prediagnostic Battery Charge" again.
007 Shift state park (P) is not selected. Press the P position switch (parking switch) to select park (P).
008 EV supply battery assembly connection malfunction Confirm the connection condition of the EV supply battery assembly.
009 GTS communication error occurred. Turn the ignition switch off and after checking that the connector of the GTS is not disconnected from the DLC3, perform "Prediagnostic Battery Charge" again.
010 Current out of the specified range
(1.7 to 10 A)
·

Confirm that the vehicle satisfies the "Vehicle Condition" specified in the following table.

·

If accessories are connected, adjust by turning the accessories on and off.


011 Battery temperature out of the specified range
(0°C (32°F) to 47°C (116.6°F))
Read the temperatures listed in "Hybrid/EV Battery Temperature 1-6".
·

When the EV battery temperature is below 0°C (32°F): Drive the vehicle until the temperature reaches 0 °C (32°F) or higher.

·

When the EV battery temperature is above 47°C (116.6°F): Leave the vehicle with the ignition switch ON (READY) and park (P) selected and wait until the EV battery temperature drops to 42°C (107.6°F) or less.


012 Time-out If the ignition switch is turned off by the time-out function, perform "Prediagnostic Battery Charge" again.
013 Low auxiliary battery voltage Inspect the auxiliary battery and DC/DC converter function.
(Click here)
014 EV battery malfunction
·

Check for HV battery system related DTCs and perform troubleshooting.

·

After checking that the master warning has turned off, perform "Prediagnostic Battery Charge" again.


015 System malfunction


vi.

The screen transitions to the next screen and "Operate the vehicle as instructed in the repair manual and turn the ignition switch to ON (READY)." is displayed.


vii.

Adjust the vehicle condition as specified in the following table.

Vehicle Condition
Item Condition
(1) Blower speed HI
(2) Air conditioning system set temperature MAX COLD
(3) Position of the mode controller damper FACE
(4) Position of the air mix controller damper Recirculate
(5) A/C switch OFF
(6) Position of the headlight dimmer switch High beam
(7) Hazard warning signal switch ON

HINT:

Turn off all switches other than the headlight dimmer switch, hazard warning signal switch and air conditioning system related switches.



viii.

While depressing the brake pedal, turn the ignition switch to ON (READY).

HINT:

The READY indicator does not illuminate.



ix.

The screen transitions to the next screen and "Now diagnosing" is displayed.

HINT:
·

"Progress" is displayed as a reference to the estimated time to complete the diagnosis.

·

To suspend battery diagnosis, press "Exit" and turn the ignition switch off.




x.

The screen changes to the "Battery Diagnosis" screen and "Maintenance Required for Traction Battery at Your Dealer" is cleared simultaneously.

NOTICE:
·

It takes about 40 to 60 minutes for battery diagnosis to complete. As the diagnosis may be stopped due to an error, make sure to check the diagnosis status every ten minutes.

·

If a DTC is stored during "Battery Diagnosis", the master warning will turn on and stop the battery diagnosis.



HINT:

If battery diagnosis is suspended because the diagnosis conditions are not met anymore, the reasons for suspension are displayed on the GTS. Perform "Battery Diagnosis" after checking the causes and troubleshoot the suspected area in accordance with instructions in the "Procedure when battery diagnosis is suspended" table.



xi.

When battery diagnosis is complete, the result will be displayed.


xii.

Check the diagnosis result.

NOTICE:
·

The IG off timer function automatically turns the ignition switch off 10 minutes after the battery diagnosis completes. Make sure to confirm the diagnosis result as soon as possible.

·

To prevent the auxiliary battery from being depleted, make sure to turn the air conditioning system related switches, headlight dimmer switch and ignition switch off as soon as "Battery Diagnosis" is complete.



HINT:

As "Battery Diagnosis" discharges the EV supply battery assembly to a low SOC, if the ignition switch is turned to ON immediately after the "Battery Diagnosis" is completed, DTC P300000 or P300016 may be stored. For this reason, leave the vehicle as is for 5 hours to allow the EV supply battery assembly SOC to recover or charge the EV supply battery assembly using the THS Charger. Then, clear the DTCs and check that no DTCs are output. If DTC P300000 or P300016 is output again, perform troubleshooting for the DTC.


Result:

If the diagnosis result states to replace an EV supply stack sub-assembly, replace the listed EV supply stack sub-assembly.



xiii.

Press "Exit", turn the ignition switch off and wait for 60 seconds or more.

HINT:
·

If the diagnosis result is "Replace the HV battery", replace the EV supply battery assembly.

·

After performing Battery Diagnosis, the trip will be determined to have ended when 60 seconds have elapsed since the ignition switch was turned off. If the ignition switch is attempted to be turned to ON (READY) before 60 seconds have elapsed since the ignition switch was turned off, it may not be able to be turned to ON (READY).




xiv.

As the SOC of the EV supply battery assembly will be low after performing "Battery Diagnosis", charge the EV supply battery assembly by turning the ignition switch to ON (READY) and allowing the FC system to idle until it stops.



b.

When manually starting "Battery Diagnosis":

i.

Perform the following procedure within 60 seconds of the ignition switch being turned to ON.

1.

Check that park (P) is selected. (Do not depress the accelerator pedal.)

2.

While depressing the brake pedal with your left foot, select neutral (N) and fully depress the accelerator pedal three times with your right foot.

3.

Press the P position switch to select park (P), and then fully depress the accelerator pedal once.

4.

While depressing the brake pedal with your left foot, move the shift lever to select neutral (N) and fully depress the accelerator pedal three times with your right foot.

5.

Press the P position switch to select park (P), and then fully depress the accelerator pedal once.


HINT:

Fully depressing the accelerator pedal from the closed position is counted as one operation.



ii.

Wait for 5 seconds.


iii.

Adjust the vehicle condition as specified in the following table.

Vehicle Condition
Item Condition
(1) Blower speed HI
(2) Air conditioning system set temperature MAX COLD
(3) Position of the mode controller damper FACE
(4) Position of the air mix controller damper Recirculate
(5) A/C switch OFF
(6) Position of the headlight dimmer switch High beam
(7) Hazard warning signal switch ON

HINT:

Turn off all switches other than the headlight dimmer switch, hazard warning signal switch and air conditioning system related switches.



iv.

While depressing the brake pedal, turn the ignition switch to ON (READY).

HINT:

The READY indicator does not illuminate.



v.

The screen changes to the "Battery Diagnosis" screen and "Maintenance Required for Traction Battery at Your Dealer" is cleared simultaneously.

NOTICE:
·

It takes about 40 to 60 minutes for battery diagnosis to complete. As the diagnosis may be stopped due to an error, make sure to check the diagnosis status every ten minutes.

·

If a DTC is stored during "Battery Diagnosis", the master warning will turn on and stop the battery diagnosis.



HINT:
·

To suspend battery diagnosis, turn the ignition switch off or change the shift state from park (P).

·

If the diagnosis conditions are not met, the ignition switch will turn off immediately after it is turned to ON (READY). In this case, "Voltage too low", "EV supply battery assembly connection malfunction" or "Battery temperature out of the specified range" will be the reason for diagnosis suspension. Troubleshoot the suspected area in accordance with instructions in the "Procedure when battery diagnosis is suspended" table.



Procedure when battery diagnostic is suspended
Reason of Diagnosis Suspension
(Related Condition)
Procedure
Voltage too low Turn the ignition switch off and then perform "Prediagnostic Battery Charge" again.
EV supply battery assembly connection malfunction Confirm the connection condition of the EV supply battery assembly.
Current out of the specified range
(1.7 to 10 A)
·

Confirm that the vehicle satisfies the "Vehicle Condition" specified in the previous table.

·

If accessories are connected, adjust by turning the accessories on and off.


Battery temperature out of the specified range
(0°C (32°F) to 47°C (116.6°F))
·

When the EV battery temperature is below 0°C (32°F): Drive the vehicle until the temperature reaches 0°C (32°F) or higher.

·

When the EV battery temperature is above 47°C (116.6°F): Leave the vehicle with the ignition switch ON (READY) and park (P) selected and wait until the EV battery temperature drops to 42°C (107.6°F) or less.




vi.

Approximately 2 hours after "Battery Diagnosis" is started, the ignition switch is automatically turned off. Turn the ignition switch back to ON and check the diagnosis result.

HINT:

The IG off timer function automatically turns the ignition switch off 10 minutes after "Battery Diagnosis" (which takes approximately 40 to 60 minutes) is complete.


1.

After the ignition switch has been automatically turned off, turn the ignition switch to ON.

2.

Check the multi-information display.

Multi-information Display Diagnosis Result
"Maintenance Required for Traction Battery at Your Dealer" is displayed. Replace the EV supply battery assembly or "Battery Diagnosis" suspended due to an error.
"Maintenance Required for Traction Battery at Your Dealer" is not displayed. There is no need to replace EV supply battery assembly.


HINT:
·

As "Battery Diagnosis" discharges the EV supply battery assembly to a low SOC, if the ignition switch is turned to ON immediately after the "Battery Diagnosis" is completed, DTC P300000 or P300016 may be stored. For this reason, leave the vehicle as is for 5 hours to allow the EV supply battery assembly SOC to recover or charge the EV supply battery assembly using the THS Charger. Then, clear the DTCs and check that no DTCs are output. If DTC P300000 or P300016 is output again, perform troubleshooting for the DTC.

·

If "Maintenance Required for Traction Battery at Your Dealer" is displayed, "Battery Diagnosis" may have been suspended due to a malfunction. Perform "Prediagnostic Battery Charge" and "Battery Diagnosis" using the GTS.

·

By performing "Battery Diagnosis" using the GTS, the EV supply stack sub-assembly to be replaced can be determined.




vii.

Turn the ignition switch off and wait for 60 seconds or more.

HINT:
·

If the diagnosis result is "Replace the HV battery", replace the EV supply battery assembly.

·

After performing Battery Diagnosis, the trip will be determined to have ended when 60 seconds have elapsed since the ignition switch was turned off. If the ignition switch is attempted to be turned to ON (READY) before 60 seconds have elapsed since the ignition switch was turned off, it may not be able to be turned to ON (READY).




viii.

As the SOC of the EV supply battery assembly will be low after performing "Battery Diagnosis", charge the EV supply battery assembly by turning the ignition switch to ON (READY) and allowing the FC system to idle until it stops.




TEMPORARY VEHICLE START UP


NOTICE:
·

Do not perform temporary vehicle start up while the master warning is illuminated.

·

Perform only when "Vehicle Start Unavailable until Traction Battery Inspected Contact Your Dealer" is displayed on the multi-information display and the vehicle cannot be started.

·

"Vehicle Start Unavailable until Traction Battery Inspected Contact Your Dealer" is not cleared even after "Temporary Vehicle Start Up" is performed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Powertrain / EV Battery / Utility / Temporary Vehicle Start Up

Powertrain > EV Battery > Utility
Tester Display
Temporary Vehicle Start Up
50005 398 8001
NOTICE:

If the ignition switch is turned to ON (READY) while depressing the brake pedal, "Temporary Vehicle Start Up" is not possible. Retry after turning the ignition switch off.



d.

Check items on the display and press "Next".


e.

The screen transitions to the next screen and "Please wait" is displayed.


f.

The screen transitions to the next screen and "Now the vehicle is ready to start." is displayed.

HINT:
·

If the ignition switch is turned off after "Temporary Vehicle Start Up", the vehicle will not be able to start again.

·

The GTS can be disconnected after turning the ignition switch to ON (READY).




g.

Perform "Prediagnostic Battery Charge".

i.

Enter the following menus: Powertrain / EV Battery / Utility / Prediagnostic Battery Charge.

Powertrain > EV Battery > Utility
Tester Display
Prediagnostic Battery Charge
50005 398 4181
HINT:

Refer to Prediagnostic Battery Charge.




h.

Perform "Battery Diagnosis".

i.

Enter the following menus: Powertrain / EV Battery / Utility / Battery Diagnosis.

Powertrain > EV Battery > Utility
Tester Display
Battery Diagnosis
50005 398 4182
HINT:

Refer to Battery Diagnosis.




i.

Turn the ignition switch to ON (READY).


j.

When the condition to perform "Temporary Vehicle Start Up" is not met, the reasons for suspension are displayed on the GTS. Perform "Temporary Vehicle Start Up" again after checking the causes and troubleshooting the suspected area in accordance with instructions in the "Procedure when temporary vehicle start up is suspended" table.

Procedure when "Temporary Vehicle Start Up" is suspended
GTS Display Reason for Temporary Vehicle Start Up Suspension
(Related Condition)
Procedure
Temporary Vehicle Start Up has failed. Confirm the following condition. GTS communication error After checking that the connector of the GTS is not disconnected and the ignition switch is ON, perform "Temporary Vehicle Start Up" again.



HIGH VOLTAGE FUSE ACCUMULATED LOAD HISTORY RESET


HINT:

If the EV battery terminal block has been replaced, make sure to perform "High Voltage Fuse Accumulated Load History Reset" and then clear the DTCs.

DTC P0A9563 will be stored again if do not perform "High Voltage Fuse Accumulated Load History Reset".


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Powertrain / EV Battery / Utility / High Voltage Fuse Accumulated Load History Reset.

Powertrain > EV Battery > Utility
Tester Display
High Voltage Fuse Accumulated Load History Reset
50005 398 8002

d.

According to the display on the GTS, perform High Voltage Fuse Accumulated Load History Reset and check that "High Voltage Fuse Accumulated Load History Reset is complete." is displayed.

HINT:

If "High Voltage Fuse Accumulated Load History Reset has failed. Do you want to try again?" is displayed on the GTS, perform the procedure again.



e.

Turn the ignition switch off.