| DTC | Trouble Area | Parking Brake Indicator Light | Brake System Warning Light (Yellow) | Fail-safe Deactivation Condition |
|---|---|---|---|---|
| C059704 | No. 2 skid control ECU (brake actuator assembly) internal malfunction | Normal* | Illuminates | After the conditions return to normal, the ignition switch is turned to ON and the parking brake is applied and released |
| C059746 | No. 2 skid control ECU (brake actuator assembly) internal malfunction | Normal | Illuminates | After the conditions return to normal, the ignition switch is turned to ON and the parking brake is applied and released |
| C060962 | Electric parking brake switch assembly malfunction (open or short) | Blinks | Illuminates | After the conditions return to normal, the electric parking brake switch assembly is operated |
| C112012 | Tension sensor 1 malfunction (short to +B) | Blinks | Illuminates | After the conditions return to normal, the ignition switch is turned to ON (recovery not possible after release control performed during malfunction) |
| C112014 | Tension sensor 1 malfunction (short to ground/open circuit) | Blinks | Illuminates | After the conditions return to normal, the ignition switch is turned to ON (recovery not possible after release control performed during malfunction) |
| C112512 | Tension sensor 2 malfunction (short to +B) | Blinks | Illuminates | After the conditions return to normal, the ignition switch is turned to ON (recovery not possible after release control performed during malfunction) |
| C112514 | Tension sensor 2 malfunction (short to ground/open circuit) | Blinks | Illuminates | After the conditions return to normal, the ignition switch is turned to ON (recovery not possible after release control performed during malfunction) |
| C112A62 | Tension sensor 1/2 signal comparison malfunction | Blinks | Illuminates | After the conditions return to normal, the ignition switch is turned to ON (recovery not possible after release control performed during malfunction) |
| C112B11 | Tension sensor power source malfunction (short to ground) | Blinks | Illuminates | After the conditions return to normal, the ignition switch is turned to ON (recovery not possible after release control performed during malfunction) |
| C112B12 | Tension sensor power source malfunction (short to +B) | Blinks | Illuminates | After the conditions return to normal, the ignition switch is turned to ON (recovery not possible after release control performed during malfunction) |
| C112B13 | Tension sensor power source malfunction (open circuit) | Blinks | Illuminates | After the conditions return to normal, the ignition switch is turned to ON (recovery not possible after release control performed during malfunction) |
| C113011 | Parking brake actuator assembly with bracket circuit malfunction (short to ground) | Normal* | Illuminates | After the conditions return to normal, the ignition switch is turned to ON and the parking brake is applied and released |
| C113012 | Parking brake actuator assembly with bracket circuit malfunction (short to +B) | Normal* | Illuminates | After the conditions return to normal, the ignition switch is turned to ON and the parking brake is applied and released |
| C113013 | Parking brake actuator assembly with bracket circuit malfunction (open circuit) | Normal* | Illuminates | After the conditions return to normal, the ignition switch is turned to ON and the parking brake is applied and released |
| C113014 | Parking brake actuator assembly with bracket circuit malfunction (short to ground/open circuit) | Normal* | Illuminates | After the conditions return to normal, the ignition switch is turned to ON and the parking brake is applied and released |
| C113319 | Parking brake actuator assembly with bracket circuit malfunction (overcurrent) | Normal* | Illuminates | After the conditions return to normal, the ignition switch is turned to ON and the parking brake is applied and released |
| C11332A | Parking brake actuator assembly with bracket malfunction (motor lock, gear lock, stuck cable) | Normal* | Illuminates | After the conditions return to normal, the DTCs are cleared |
| C11351C | No. 2 skid control ECU (brake actuator assembly) internal malfunction | Normal* | Illuminates | Ignition switch off (recovery not possible after release control performed during malfunction) |
| C123A14 | IG power source malfunction (open) | Normal* | Illuminates | After returning to normal condition, turn ignition switch again |
| C13B516 | +BS power source malfunction (open) | Normal* | Illuminates | After returning to normal condition, turn ignition switch again |
| C13B800 | Parking brake actuator assembly with bracket malfunction (repeated slipping) | Normal* | Illuminates | After the conditions return to normal, the ignition switch is turned to ON and the parking brake is applied and released |
| C13B813 | Parking brake actuator assembly with bracket malfunction (disconnected cable) | Normal* | Illuminates | After the conditions return to normal, the DTCs are cleared |
| C13B877 | Parking brake actuator assembly with bracket malfunction (defective operation) | Normal* | Illuminates | After the conditions return to normal, the DTCs are cleared |
| C13B879 | Parking brake actuator assembly with bracket malfunction (free spinning) | Normal* | Illuminates | After the conditions return to normal, the DTCs are cleared |
| C13B896 | Tension sensor internal malfunction | Blinks | Illuminates | After the conditions return to normal, the ignition switch is turned to ON (recovery not possible after release control performed during malfunction) |
*: The parking brake indicator light blinks if the electric parking brake switch assembly is pulled or pushed.