This DTC is output when an open circuit or short occurs in the communication line between a rear center ultrasonic sensor (RLC sensor) and the rear center ultrasonic sensor (RRC sensor), or when a malfunction occurs in a rear center ultrasonic sensor (RLC sensor) on the rear.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C1AE787 | Ultrasonic Sensor (Rear Left Center) Missing Message | Rear center ultrasonic sensor (RLC sensor) lost communication | ·
Rear center ultrasonic sensor (RLC sensor) ·
Harness or connector ·
Clearance warning ECU assembly |
Clearance Warning | B |
Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>CALIBRATION
If a DTC is detected again after the repair, turn the ignition switch to ON and turn the TOYOTA parking assist-sensor system on, and then clear the DTC.
If C1AE896 is output at the same time, check C1AE896 first.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE896
Check the vehicle condition and work details.
| Result | Proceed to |
|---|---|
| The clearance warning ECU assembly or ultrasonic sensor has not been replaced | A |
| The clearance warning ECU assembly or ultrasonic sensor has been replaced | B |
A
B
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION
Check that the connector is properly connected to the rear corner ultrasonic sensor and rear center ultrasonic sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| C1AE787 is not output | A |
| C1AE787 is output | B |
A
B
Check that the connector is properly connected to the clearance warning ECU assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| C1AE687, C1AE787, C1AE887 and C1AE987 are output | B |
| C1AE687, C1AE787 and C1AE887 are output | C |
| C1AE687 and C1AE787 are output | D |
| C1AE687 is output | E |
| Only C1AE787 is output | F |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE987
C
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE887
D
E
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE687
F
Pre-procedure1
Disconnect the J22 rear center ultrasonic sensor (RRC sensor) connector.
Disconnect the J21 rear center ultrasonic sensor (RLC sensor) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(J22,J21)Location & Routingewd_type=routing;type=c,c;code=J22,J21 Click Connector(J22)Body>No. 1 Luggage Room Wire / No. 3 Luggage Room Wire>Rear Center Ultrasonic Sensor RHewd_type=component;type=c;code=J22;pinno=1,2,3 Click Connector(J21)Body>No. 1 Luggage Room Wire / No. 3 Luggage Room Wire>Rear Center Ultrasonic Sensor LHewd_type=component;type=c;code=J21;pinno=4,5,6 |
||
| J22-1 (BO) - J21-4 (BI) | Always | Below 1 Ω |
| J22-2 (SO) - J21-5 (SI) | Always | Below 1 Ω |
| J22-3 (EO) - J21-6 (EI) | Always | Below 1 Ω |
| J22-1 (BO) or J21-4 (BI) - Body ground | Always | 10 kΩ or higher |
| J22-2 (SO) or J21-5 (SI) - Body ground | Always | 10 kΩ or higher |
| J22-3 (EO) or J21-6 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the rear center ultrasonic sensor (RLC sensor) with a known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| C1AE787 is not output | A |
| C1AE787 is output | B |
A
B