Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455111 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  No. 2 Clearance Warning Buzzer Circuit  


DESCRIPTION

This circuit consists of the No. 2 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The ECU operates the buzzers using a sound pattern that changes depending on the distance to the obstacle.

WIRING DIAGRAM

E433063E15
2.063,0.354 2.188,0.583 0.125,0.229 10 false 1 2.063,1.135 2.24,1.365 0.177,0.229 10 false 2 1.073,1.667 1.406,1.896 0.333,0.229 10 false G29 1.073,1.833 2.135,2.24 1.063,0.406 10 false No. 2 Clearance Warning Buzzer 5.417,1.792 5.729,2.021 0.313,0.229 10 false G20 5.417,1.958 6.615,2.344 1.198,0.385 10 false Clearance Warning ECU Assembly 5.271,0.354 5.479,0.573 0.208,0.219 10 false 26 5.573,0.458 5.927,0.677 0.354,0.219 10 false BBZ 5.271,1.135 5.469,1.323 0.198,0.188 10 false 25 5.583,1.25 5.865,1.448 0.281,0.198 10 false ER 1.74,0.448 2.052,0.646 0.313,0.198 10 false Z+ 1.771,1.229 2.083,1.427 0.313,0.198 10 false Z-

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Check that the buzzer operates by performing the Active Test.

Body Electrical > Clearance Warning > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Buzzer No. 2 clearance warning buzzer No. 2 clearance warning buzzer Confirm that the vehicle is stopped and the ignition switch is ON
Body Electrical > Clearance Warning > Active Test
Tester Display
Rear Buzzer
50004 438 2
OK:

The No. 2 clearance warning buzzer sounds.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 2 CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 2 CLEARANCE WARNING BUZZER)
a.

Disconnect the G20 clearance warning ECU assembly connector.


b.

Disconnect the G29 No. 2 clearance warning buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G20,G29)Location & Routing

Click Connector(G20)Body>Floor Wire / No. 3 Floor Wire>Clearance Warning ECU Assembly

Click Connector(G29)Body>Floor Wire / No. 3 Floor Wire>No. 1 Clearance Warning Buzzer

G20-26 (BBZ) - G29-1 (Z+) Always Below 1 Ω
G20-25 (ER) - G29-2 (Z-) Always Below 1 Ω
G20-26 (BBZ) or G29-1 (Z+) - Body ground Always 10 kΩ or higher
G20-25 (ER) or G29-2 (Z-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 2 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 2 CLEARANCE WARNING BUZZER
a.

Replace the No. 2 clearance warning buzzer with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER (for Rear Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.PERFORM ACTIVE TEST USING GTS
4.PERFORM ACTIVE TEST USING GTS
a.

Check that the buzzer operates by performing the Active Test.

Body Electrical > Clearance Warning > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Buzzer No. 2 clearance warning buzzer No. 2 clearance warning buzzer Confirm that the vehicle is stopped and the ignition switch is ON
Body Electrical > Clearance Warning > Active Test
Tester Display
Rear Buzzer
50004 438 2
OK:

The No. 2 clearance warning buzzer sounds.



Result:
Proceed to
OK
NG



OK

END (NO. 2 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

NG