Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM D

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  UTILITY  


ALL READINESS


HINT:
·

With "All Readiness", you can check whether or not the DTC judgment has been completed by using the GTS.

·

You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.



a.

Clear the DTCs even if no DTCs are stored.

Powertrain > EV > Clear DTCs
50002 397

b.

Turn the ignition switch off and wait for 10 minutes or more.


c.

Turn the ignition switch to ON.


d.

Perform the DTC judgment driving pattern to run the DTC judgment.

Powertrain > EV > Utility
Tester Display
All Readiness
50005 397 1020

e.

Input the DTCs to be confirmed.


f.

Check the DTC judgment result.

GTS Display Description

If the judgment result shows Incomplete, perform the DTC confirmation driving pattern again.

Normal
·

DTC judgment completed

·

System normal


Abnormal
·

DTC judgment completed

·

System abnormal


Incomplete
·

DTC judgment not completed

·

Perform the driving pattern




g.

Turn the ignition switch off.



DIAGNOSIS RELATED INFORMATION


a.

Check for diagnosis related information.

Powertrain > EV > Utility
Tester Display
Diagnosis Related Information
50005 397 1056
i.

Check the Diagnosis Related Information, and then write them down.



b.

Clear diagnosis related information.

NOTICE:

Clearing the DTCs will also clear the diagnosis related information.


i.

Enter the following menus: Powertrain / EV / Clear DTCs.

Powertrain > EV > Clear DTCs
50002 397

ii.

Clear the diagnosis related information and freeze frame data.


iii.

Turn the ignition switch off.




VIN (VEHICLE IDENTIFICATION NUMBER)


NOTICE:

The Vehicle Identification Number (VIN) must be written to a replacement EV Control ECU.


HINT:

The VIN is a 17-digit alphanumeric vehicle identification number. The GTS is required to register the VIN.


a.

DESCRIPTION

HINT:

This registration section consists of 2 parts: Read VIN and Write VIN.


i.

Read VIN: This procedure allows the VIN stored in the EV Control ECU to be read in order to confirm that the 2 VINs, provided with the vehicle and stored in the vehicle EV Control ECU, are the same.


ii.

Write VIN: This procedure allows the VIN to be written to the EV Control ECU. If the EV Control ECU is replaced, or the EV Control ECU VIN and vehicle VIN do not match, the VIN can be registered, or overwritten in the EV Control ECU by following this procedure.



b.

READ VIN

i.

Confirm the vehicle VIN.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / EV / Utility / VIN / VIN Read.

Powertrain > EV > Utility
Tester Display
VIN
50005 397 3660

vi.

According to the display on the GTS, read the VIN stored in the EV Control ECU.



c.

WRITE VIN

i.

Confirm the vehicle VIN.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / EV / Utility / VIN / VIN Write.

Powertrain > EV > Utility
Tester Display
VIN
50005 397 3660

vi.

According to the display on the GTS, write the VIN to the EV Control ECU.