Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Drive Start Control  


DESCRIPTION

The drive start control is controlled by the EV control ECU.

If the EV control ECU determines that the shift lever and accelerator pedal are operated abnormally, FC system output is restricted and, when necessary, a warning is displayed on the combination meter assembly.

A467946E03
0.375,0.25 1.958,0.875 1.583,0.625 10 false Accelerator Pedal Sensor Assembly 0.406,1.479 1.927,2.135 1.521,0.656 10 false Yaw Rate Sensor 0.406,2.615 2.573,3.25 2.167,0.635 10 false Shift Lever Position Sensor 0.396,3.406 1.979,3.813 1.583,0.406 10 false Vehicle Speed Sensor or Wheel Speed Sensor 2.917,3.771 4.031,4.125 1.115,0.354 10 false Vehicle speed 3.042,2.875 4.865,3.208 1.823,0.333 10 false Shift state 2.677,1.854 3.99,2.281 1.313,0.427 10 false Vehicle acceleration 2.76,0.625 3.938,1 1.177,0.375 10 false Actual accelerator opening 5.427,1.073 7.052,1.667 1.625,0.594 10 false Meter display request 5.5,3.115 6.625,3.594 1.125,0.479 10 false FC system output request 3.99,4.177 5.302,4.542 1.313,0.365 10 false EV Control ECU

CAUTION / NOTICE / HINT

HINT:

Even if the accelerator pedal position is maintained, the hybrid control system output may increase when driving uphill and decrease when driving downhill. This is due to drive start control controlling the hybrid control system output, and is not a malfunction.


PROCEDURE

1.SYMPTOM CONFIRMATION
a.

Interview the customer to confirm the problem.


Result:
Proceed to
Hunting
Hesitation/poor acceleration



Hunting

2.PAST ACTIVATION CONFIRMATION

Hesitation/poor acceleration

7.PAST ACTIVATION CONFIRMATION
2.PAST ACTIVATION CONFIRMATION
a.

Check if the customer operated the vehicle in a way that would cause the drive start control to operate.

HINT:
Drive Start Control Activation Conditions
Shift control

Activation conditions


·

Pattern A (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift state is changed from park (P) to any forward shift state (drive (D) or manual (B)) or reverse (R).



·

Pattern B (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift state is changed from reverse (R) to any forward shift state (drive (D) or manual (B)), any forward shift state (drive (D) or manual (B)) to reverse (R), or neutral (N) to reverse (R).

A396026E91
4.594,3.958 5.354,3.479 true 4.052,3.5 4.948,3.042 true 4.063,3.042 4.344,2.615 true 2.604,1.719 4.906,1.479 true 3.094,0.99 3.781,0.563 true 3.271,4.115 3.885,4.313 0.615,0.198 10 false Time 5.125,3.313 6.5,3.563 1.375,0.25 10 false with control * 4.198,2.438 5.188,2.708 0.99,0.271 10 false without control 4.833,2.875 5.604,3.167 0.771,0.292 10 false Restricted 2.781,2.51 3.365,2.771 0.583,0.26 10 false Activated 0.771,3.271 2.25,3.656 1.479,0.385 10 false FC System Output 0.99,1.198 2.26,1.542 1.271,0.344 10 false Shift Lever Position 0.802,1.958 2.25,2.25 1.448,0.292 10 false Accelerator Pedal OFF 4.948,1.281 6.833,1.938 1.885,0.656 10 false Accelerator pedal is open by approximately 1/5 or more. 3.771,0.417 6.302,0.76 2.531,0.344 10 false Shift operation of pattern A or pattern B 0.865,1.646 2.25,1.979 1.385,0.333 10 false Accelerator Pedal ON 4.438,4.125 7.094,4.74 2.656,0.615 10 false *: The hybrid system output restricted level differs between pattern A and pattern B.

If the shift lever is moved to attempt to change the shift state from park (P) when the accelerator pedal is depressed, the shift state will not change and drive-start control will not operate.



·

Items Controlled

-

FC system output is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift state is in park (P) or neutral (N).



Reverse control

Activation conditions


·

The shift state is in reverse (R).

·

The accelerator pedal is depressed excessively.

C455552E01
3.323,1.344 5.198,0.979 true 4.177,3.25 5.667,2.75 true 4.521,2.885 4.938,2.469 true 4.719,3.542 5.635,3.25 true 0.948,3.167 2.375,3.646 1.427,0.479 10 false FC System Output 3.625,4.042 4.24,4.24 0.615,0.198 10 false Time 5.563,3.073 6.375,3.292 0.813,0.219 10 false with control 5.563,2.573 6.438,2.844 0.875,0.271 10 false Restricted 4.677,2.281 5.615,2.646 0.938,0.365 10 false without control 2.896,2.406 3.677,2.677 0.781,0.271 10 false Activated 1.104,0.781 2.438,1.083 1.333,0.302 10 false Shift Lever Position 1.083,1.271 2.5,1.583 1.417,0.313 10 false Accelerator Pedal ON 1.031,1.656 2.521,2.01 1.49,0.354 10 false Accelerator Pedal OFF 5.25,0.771 7.135,1.365 1.885,0.594 10 false When the accelerator pedal is suddenly depressed. 2.76,0.781 2.917,0.979 0.156,0.198 10 false R


·

Items Controlled

-

Driving force is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift state is changed to any shift state other than reverse (R).




HINT:
·

The driving force restricted level differs between pattern A, pattern B and Reverse control.

·

During reverse control or shift control, driving force is adjusted based on the road gradient and steering angle.




Result:
Result Proceed to
Performed A
Not performed B



A

3.CHECK DTC OUTPUT (HEALTH CHECK)

B

3.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Enter the following menus: System Select / Health Check.


b.

Check the DTCs.


Result:
Proceed to
DTCs are not output
DTC is output


c.

Turn the ignition switch off.



DTCs are not output

4.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

DTC is output

GO TO DTC CHART

4.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
a.

Read the value displayed on the GTS.

HINT:

If the Data List updates slowly, perform measurement after selecting only the "FR Wheel Speed", "FL Wheel Speed", "RR Wheel Speed" and "RL Wheel Speed" items.


Chassis > Brake/EPB > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 435 13,14,15,16
Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) When driving at constant speed: No large fluctuations
Standard:
Condition Specified Condition
Vehicle stopped 0 km/h (0 mph)
Vehicle being driven at constant speed between 16 to 64 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (VEHICLE SPEED)

NG

5.READ VALUE USING GTS (VEHICLE SPEED)
a.

Read the value of "Vehicle Speed" displayed on the GTS.

HINT:

If the Data List updates slowly, perform measurement after selecting only the "Vehicle Speed" item.


Powertrain > EV > Data List
Tester Display
Vehicle Speed
50003 397 12
Powertrain > EV > Data List
Tester Display Measurement Item Range Normal Condition
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Vehicle stopped: 0 km/h (0 mph)
While driving at a constant speed: No significant fluctuation
Standard:
Inspection Condition Specified Condition
Vehicle stopped 0 km/h (0 mph)
Vehicle being driven at a constant speed
(16 to 64 km/h (10 to 40 mph))
No large fluctuations in displayed speed


CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (LATERAL G, FORWARD AND REARWARD G)

NG

INSPECT ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

6.READ VALUE USING GTS (LATERAL G, FORWARD AND REARWARD G)
a.

Read the value displayed on the GTS.

HINT:

If the Data List updates slowly, perform measurement after selecting only the " Lateral G" and " Forward and Rearward G " items.


Chassis > Brake/EPB > Data List
Tester Display
Forward and Rearward G
50003 435 26
Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
Standard:
Condition Specified Condition
During deceleration Value changes with vehicle speed
During acceleration Value changes with vehicle speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

7.PAST ACTIVATION CONFIRMATION
a.

Check if the customer operated the vehicle in a way that would cause the drive start control to operate.

HINT:
Drive Start Control Activation Conditions
Shift control

Activation conditions


·

Pattern A (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift state is changed from park (P) to any forward shift state (drive (D) or manual (B)) or reverse (R).



·

Pattern B (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift state is changed from reverse (R) to any forward shift state (drive (D) or manual (B)), any forward shift state (drive (D) or manual (B)) to reverse (R), or neutral (N) to reverse (R).

A396026E91
4.594,3.958 5.354,3.479 true 4.052,3.5 4.948,3.042 true 4.063,3.042 4.344,2.615 true 2.604,1.719 4.906,1.479 true 3.094,0.99 3.781,0.563 true 3.271,4.115 3.885,4.313 0.615,0.198 10 false Time 5.125,3.313 6.5,3.563 1.375,0.25 10 false with control * 4.198,2.438 5.188,2.708 0.99,0.271 10 false without control 4.833,2.875 5.604,3.167 0.771,0.292 10 false Restricted 2.781,2.51 3.365,2.771 0.583,0.26 10 false Activated 0.771,3.271 2.25,3.656 1.479,0.385 10 false FC System Output 0.99,1.198 2.26,1.542 1.271,0.344 10 false Shift Lever Position 0.802,1.958 2.25,2.25 1.448,0.292 10 false Accelerator Pedal OFF 4.948,1.281 6.833,1.938 1.885,0.656 10 false Accelerator pedal is open by approximately 1/5 or more. 3.771,0.417 6.302,0.76 2.531,0.344 10 false Shift operation of pattern A or pattern B 0.865,1.646 2.25,1.979 1.385,0.333 10 false Accelerator Pedal ON 4.438,4.125 7.094,4.74 2.656,0.615 10 false *: The hybrid system output restricted level differs between pattern A and pattern B.

If the shift lever is moved to attempt to change the shift state from park (P) when the accelerator pedal is depressed, the shift state will not change and drive-start control will not operate.



·

Items Controlled

-

FC system output is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift state is in park (P) or neutral (N).



Reverse control

Activation conditions


·

The shift state is in reverse (R).

·

The accelerator pedal is depressed excessively.

C455552E01
3.323,1.344 5.198,0.979 true 4.177,3.25 5.667,2.75 true 4.521,2.885 4.938,2.469 true 4.719,3.542 5.635,3.25 true 0.948,3.167 2.375,3.646 1.427,0.479 10 false FC System Output 3.625,4.042 4.24,4.24 0.615,0.198 10 false Time 5.563,3.073 6.375,3.292 0.813,0.219 10 false with control 5.563,2.573 6.438,2.844 0.875,0.271 10 false Restricted 4.677,2.281 5.615,2.646 0.938,0.365 10 false without control 2.896,2.406 3.677,2.677 0.781,0.271 10 false Activated 1.104,0.781 2.438,1.083 1.333,0.302 10 false Shift Lever Position 1.083,1.271 2.5,1.583 1.417,0.313 10 false Accelerator Pedal ON 1.031,1.656 2.521,2.01 1.49,0.354 10 false Accelerator Pedal OFF 5.25,0.771 7.135,1.365 1.885,0.594 10 false When the accelerator pedal is suddenly depressed. 2.76,0.781 2.917,0.979 0.156,0.198 10 false R


·

Items Controlled

-

FC system output is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift state is changed to any shift state other than reverse (R).




HINT:
·

The FC system output restricted level differs between pattern A, pattern B and Reverse control.

·

During reverse control or shift control, FC system output is adjusted based on the road gradient and steering angle.




Result:
Result Proceed to
Not performed A
Performed B


HINT:

If the customer operated the vehicle in a way which caused the drive start control to operate, explain the operation of the system to the customer and that the operation is not a malfunction.



A

8.CHECK DTC OUTPUT (HEALTH CHECK)

B

SYSTEM NORMAL

8.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Enter the following menus: System Select / Health Check.


b.

Check the DTCs.


Result:
Result Proceed to
DTCs are not output A
DTC is output B


c.

Turn the ignition switch off.



A

9.READ VALUE USING GTS (SHIFT POSITION)

B

GO TO DTC CHART

9.READ VALUE USING GTS (SHIFT POSITION)
a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Shift Position
50003 397 231
Powertrain > EV > Data List
Tester Display Measurement Item Range Normal Condition
Shift Position Current shift state P / R / N / D / B Matches currently selected shift state:
park (P), reverse (R), neutral (N), drive (D) or manual (B)
OK:
Condition Specified Condition
Select shift state Matches currently selected shift state



b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

NG

10.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)
a.

Read the value displayed on the GTS.

HINT:

If the Data List updates slowly, perform measurement after selecting only the "Accelerator Position Sensor No.1 Voltage %" and "Accelerator Position Sensor No.2 Voltage %" items.


Powertrain > EV > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage %
Accelerator Position Sensor No.2 Voltage %
50003 397 23,24
Powertrain > EV > Data List
Tester Display Measurement Item Range Normal Condition
Accelerator Position Sensor No.1 Voltage % Accelerator pedal position sensor No. 1 Min.: 0.0%, Max.: 100.0% Accelerator pedal depressed:
Changes with accelerator pedal pressure
Accelerator Position Sensor No.2 Voltage % Accelerator pedal position sensor No. 2 Min.: 0.0%, Max.: 100.0% Accelerator pedal depressed:
Changes with accelerator pedal pressure
OK:
Condition Specified Condition
Accelerator Pedal Released → Depressed Values smoothly change following accelerator pedal operation



b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY