Home › ADAS / AD › ADVANCED PARK › ADVANCED PARK
RM37H0E _95 ADAS / AD _095318 ADVANCED PARK _0455116 ADVANCED PARK C

ADVANCED PARK  ADVANCED PARK  U117987  Lost Communication with Image Processing Module "B" (ch2)  


DESCRIPTION

This DTC is output when the clearance warning ECU assembly detects lost communication with the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U117987 Lost Communication with Image Processing Module "B" (ch2) The clearance warning ECU assembly is unable to receive communication from the parking assist ECU
·

Open or short in bus main line

·

Clearance warning ECU assembly internal malfunction

·

Parking assist ECU internal malfunction

·

Parking assist ECU power source circuit malfunction


Clearance Warning A

WIRING DIAGRAM

E456285E03
5.271,1.958 6.792,2.354 1.521,0.396 10 false Clearance Warning ECU Assembly 5.271,1.771 5.698,2 0.427,0.229 10 false G20 5.646,0.802 6.073,1.031 0.427,0.229 10 false CAPH 5.677,1.479 6.104,1.708 0.427,0.229 10 false CAPL 1.115,0.771 1.542,1 0.427,0.229 10 false CAPH 1.125,1.49 1.552,1.719 0.427,0.229 10 false CAPL 5.333,0.792 5.76,1.021 0.427,0.229 10 false 35 5.333,1.25 5.76,1.479 0.427,0.229 10 false 36 0.542,1.958 2.448,2.271 1.906,0.313 10 false Parking Assist ECU 0.531,1.781 0.958,2.01 0.427,0.229 10 false G13 1.635,0.802 2.063,1.031 0.427,0.229 10 false 9 1.604,1.24 2.031,1.469 0.427,0.229 10 false 10

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK CAN BUS MAIN WIRE (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the clearance warning ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G20,D20)Location & Routing

Click Connector(G20)Body>Floor Wire / No. 3 Floor Wire>Clearance Warning ECU Assembly

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

G20-37 (CANH) - G20-38 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
G20-37 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G20-38 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G20-37 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G20-38 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

2.CHECK CAN BUS MAIN WIRE (CLEARANCE WARNING ECU ASSEMBLY)
2.CHECK CAN BUS MAIN WIRE (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the clearance warning ECU connector.


b.

Disconnect the parking assist ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G13,D20)Location & Routing

Click Connector(G13)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

G13-9 (CAPH) - G13-10 (CAPL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
G13-9 (CAPH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G13-10 (CAPL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G13-9 (CAPH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G13-10 (CAPL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR