Home › Engine / Hybrid System › FC CONTROL › RELAY
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466414 RELAY G

FC CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 89501B 1.INSPECT FC-B RELAY

a.
E218162E16
0.802,0.865 1.042,0.448 true 0.823,1.531 0.823,1.823 true 1.094,1.094 1.365,1.094 true 0.26,1.083 0.531,1.083 true 1.813,1.25 1.969,1.448 0.156,0.198 10 false 1 3.135,1.25 3.292,1.448 0.156,0.198 10 false 2 1.823,0.771 1.979,0.969 0.156,0.198 10 false 3 3.135,0.781 3.292,0.979 0.156,0.198 10 false 5 0.146,1.021 0.302,1.219 0.156,0.198 10 false 1 1.417,1.021 1.573,1.219 0.156,0.198 10 false 2 1.115,0.344 1.271,0.542 0.156,0.198 10 false 5 0.802,1.865 0.958,2.063 0.156,0.198 10 false 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the FC-B relay.


Hide 28371C 2.INSPECT NO. 2 IGNITION RELAY (IG2)

a.
A281356N06
1.302,0.583 1.198,0.583 1.198,0.583 1.104,0.938 false 0.292,0.729 0.406,0.729 0.406,0.729 0.563,0.979 false 1.385,1.604 1.281,1.604 1.281,1.604 1.115,1.344 false 0.615,1.625 0.719,1.625 0.719,1.625 0.813,1.281 false 1.344,0.49 1.5,0.688 0.156,0.198 10 false 1 1.427,1.521 1.583,1.708 0.156,0.188 10 false 2 0.156,0.635 0.302,0.823 0.146,0.188 10 false 3 0.49,1.542 0.635,1.729 0.146,0.188 10 false 5 2.365,0.604 2.531,0.813 0.167,0.208 10 false 1 2.74,1.51 2.917,1.698 0.177,0.188 10 false 5 2.354,1.51 2.531,1.708 0.177,0.198 10 false 2 2.74,0.604 2.917,0.792 0.177,0.188 10 false 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 2 ignition relay (IG2).