Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM U

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  TERMINALS OF ECU  


EV CONTROL ECU


A352214C15
0.646,0.052 1.115,0.406 0.469,0.354 1.958,0.271 2.427,0.625 0.469,0.354 3.365,0.271 3.833,0.625 0.469,0.354 4.729,0.271 5.198,0.625 0.469,0.354 6.021,0.469 6.49,0.823 0.469,0.354 0.646,0.479 1.115,0.833 0.469,0.354 6.021,0.052 6.49,0.406 0.469,0.354 0.156,0.188 0.469,0.385 0.313,0.198 10 false *1 0.76,0.135 1.219,0.333 0.458,0.198 10 false G14 2.083,0.375 2.542,0.573 0.458,0.198 10 false A15 3.49,0.385 3.948,0.583 0.458,0.198 10 false A16 4.833,0.385 5.292,0.583 0.458,0.198 10 false A17 6.177,0.146 6.635,0.344 0.458,0.198 10 false A8 0.771,0.583 1.229,0.781 0.458,0.198 10 false A14 1.156,0.063 1.469,0.26 0.313,0.198 10 false *A 1.156,0.51 1.469,0.708 0.313,0.198 10 false *B 6.156,0.573 6.615,0.771 0.458,0.198 10 false D15 6.542,0.073 6.854,0.271 0.313,0.198 10 false *A 6.552,0.5 6.865,0.698 0.313,0.198 10 false *B
*A for LHD *B for RHD
*1 EV Control ECU - -


Terminal No.
(Symbol)
Terminal Description Condition Specified Condition

*1: for LHD

*2: for RHD

A8-1 (BATT) - A17-4 (E1)*1
D15-1 (BATT) - A17-4 (E1)*2
Constant power source Ignition switch ON 11 to 14 V
Ignition switch ON (READY) 11 to 15.5 V
A16-7 (IG2) - A17-4 (E1) Power source Ignition switch ON 11 to 14 V
A17-1 (+B1) - A17-4 (E1) Power source Ignition switch ON 11 to 14 V
A8-7 (+B2) - A17-4 (E1)*1
D15-7 (+B2) - A17-4 (E1)*2
Power source Ignition switch ON 11 to 14 V
A8-21 (MREL) - A17-4 (E1)*1
D15-21 (MREL) - A17-4 (E1)*2
Main relay Ignition switch ON 11 to 14 V
A17-13 (LIN3) - A17-4 (E1) LIN communication signal
(A/C inverter, auxiliary battery state sensor)
Ignition switch ON (READY) Pulse generation
G14-3 (RLAC) - A17-4 (E1)*1
A14-3 (RLAC) - A17-4 (E1)*2
A/C relay Ignition switch ON 11 to 14 V
A17-6 (VCPA) - A17-27 (EPA) Accelerator pedal (with sensor) rod assembly power source (for VPA) Ignition switch ON 4.5 to 5.5 V
A17-33 (VPA2) - A17-25 (EPA2) Accelerator pedal (with sensor) rod assembly (for accelerator pedal sensor malfunction detection) Ignition switch ON, accelerator pedal released 1.0 to 2.2 V
Ignition switch ON, Hybrid control stem stopped, shift state in park (P), accelerator pedal fully depressed 3.4 to 5.3 V
A17-35 (VPA) - A17-27 (EPA) Accelerator pedal (with sensor) rod assembly (for accelerator pedal position detection) Ignition switch ON, accelerator pedal released 0.4 to 1.4 V
Ignition switch ON, Hybrid control stem stopped, shift state in park (P), accelerator pedal fully depressed 2.6 to 4.5 V
A17-5 (VCP2) - A17-25 (EPA2) Accelerator pedal (with sensor) rod assembly power source (for VPA2) Ignition switch ON 4.5 to 5.5 V
G14-9 (OPM2) - A17-4 (E1)*1
A14-9 (OPM2) - A17-4 (E1)*2
OIL PMP MTR relay Ignition switch ON (READY) 11 to 14 V
G14-15 (OPM1) - A17-4 (E1)*1
A14-15 (OPM1) - A17-4 (E1)*2
Oil with motor pump assembly signal Ignition switch ON (READY) Pulse generation
(Waveform 1)
G14-10 (NOPM) - A17-4 (E1)*1
A14-10 (NOPM) - A17-4 (E1)*2
Oil with motor pump assembly signal Ignition switch ON (READY) Pulse generation
(Waveform 1)
A17-7 (STP) - A17-4 (E1) Stop light switch Brake pedal depressed 11 to 14 V
Brake pedal released 0 to 1.5 V
A16-1 (ST1-) - A17-4 (E1) Stop light switch signal Brake pedal depressed 0 to 1.5 V
Brake pedal released 11 to 14 V
A17-30 (IWP) - A17-4 (E1) Water with motor pump assembly signal Ignition switch ON (READY) Pulse generation
(Waveform 2)
A17-10 (NIWP) - A17-4 (E1) Water with motor pump assembly signal Ignition switch ON (READY) Pulse generation
(Waveform 2)
A17-9 (IDH) - A17-4 (E1) External load operation prohibition request signal Ignition switch ON 0 to 2 V
A17-18 (NODD) - A17-4 (E1) DC/DC operation DC/DC converter operating normally 5 to 7 V
DC/DC converter not operating normally 2 to 4 V
DC/DC converter operating prohibited 0.1 to 0.5 V
A17-17 (VLO) - A17-4 (E1) DC/DC operation monitor / voltage change signal Ignition switch ON Pulse generation
(Waveform 3)
G14-21 (MMT) - G14-31 (MMTG)*1
A14-21 (MMT) - A14-31 (MMTG)*2
Motor temperature sensor Ignition switch ON, temperature 25°C (77°F) 3.6 to 4.6 V
Ignition switch ON, temperature 60°C (140°F) 2.2 to 3.2 V
A15-20 (TTA) - A15-28 (ETTA) Transaxle fluid temperature sensor Ignition switch ON, temperature 25°C (77°F) 3.6 to 4.6 V
Ignition switch ON, temperature 60°C (140°F) 2.2 to 3.2 V
A17-8 (HSDN) - A17-4 (E1) MG ECU shutdown signal Ignition switch ON (READY) 0 to 1.5 V
A16-17 (MTH-) - A17-4 (E1) Communication signal from MG ECU to EV control ECU Ignition switch ON (READY) Pulse generation
(Waveform 4)
A16-16 (MTH+) - A17-4 (E1) Communication signal from MG ECU to EV control ECU Ignition switch ON (READY) Pulse generation
(Waveform 4)
A16-10 (HTM+) - A17-4 (E1) Communication signal from EV control ECU to MG ECU Ignition switch ON (READY) Pulse generation
(Waveform 5)
A16-11 (HTM-) - A17-4 (E1) Communication signal from EV control ECU to MG ECU Ignition switch ON (READY) Pulse generation
(Waveform 5)
A16-15 (REQ-) - A17-4 (E1) MG ECU communication request signal Ignition switch ON (READY) Pulse generation
(Waveform 6)
A16-14 (REQ+) - A17-4 (E1) MG ECU communication request signal Ignition switch ON (READY) Pulse generation
(Waveform 6)
A16-13 (CLK-) - A17-4 (E1) MG communication clock signal Ignition switch ON Pulse generation
(Waveform 7)
A16-12 (CLK+) - A17-4 (E1) MG communication clock signal Ignition switch ON Pulse generation
(Waveform 7)
G14-2 (SMRG) - A17-3 (E01)*1
A14-2 (SMRG) - A17-3 (E01)*2
System main relay operation signal Ignition switch ON→Ignition switch ON (READY) Pulse generation
(Waveform 8)
G14-14 (SMRP) - A17-3 (E01)*1
A14-14 (SMRP) - A17-3 (E01)*2
System main relay operation signal Ignition switch ON→Ignition switch ON (READY) Pulse generation
(Waveform 8)
G14-4 (SMRB) - A17-3 (E01)*1
A14-4 (SMRB) - A17-3 (E01)*2
System main relay operation signal Ignition switch ON→Ignition switch ON (READY) Pulse generation
(Waveform 8)
A8-19 (ST2) - A17-4 (E1)*1
D15-19 (ST2) - A17-4 (E1)*2
Starter signal Ignition switch ON 0 to 1.5 V
A8-18 (IGB) - A17-4 (E1)*1
D15-18 (IGB) - A17-4 (E1)*2
Power source Ignition switch ON 11 to 14 V
A8-10 (SBFS) - A17-4 (E1)*1
D15-10 (SBFS) - A17-4 (E1)*2
Electronic shift lever system fail safe signal Ignition switch ON Pulse generation
(Waveform 9)
A8-25 (DMS+) - A17-4 (E1)*1
D15-25 (DMS+) - A17-4 (E1)*2
DRIVE MODE switch (NO. 1 Pattern Select Switch Assembly) signal Ignition switch ON, DRIVE MODE switch (NO. 1 Pattern Select Switch Assembly) not pushed 11 to 14 V
Ignition switch ON, DRIVE MODE switch (NO. 1 Pattern Select Switch Assembly) pushed and held 0 to 1.5 V
A8-30 (DMS-) - A17-4 (E1)*1
D15-30 (DMS-) - A17-4 (E1)*2
DRIVE MODE switch (NO. 1 Pattern Select Switch Assembly) signal Ignition switch ON, DRIVE MODE switch (NO. 1 Pattern Select Switch Assembly) not pushed 11 to 14 V
Ignition switch ON, DRIVE MODE switch (NO. 1 Pattern Select Switch Assembly) pushed and held 0 to 1.5 V
A8-24 (SNOW) - A17-4 (E1)*1
D15-24 (SNOW) - A17-4 (E1)*2
SNOW mode switch (Pattern Select Switch Assembly) signal Ignition switch ON, SNOW mode switch (Pattern Select Switch Assembly) not turned 11 to 14 V
Ignition switch ON, SNOW mode switch (Pattern Select Switch Assembly) being turned and held 0 to 1.5 V
A17-28 (ILK) - A17-4 (E1) Interlock switch Ignition switch ON, connector cover assembly, inverter terminal cover, front compartment main wire and service plug grip installed correctly 0 to 1.5 V
Ignition switch ON, connector cover assembly, inverter terminal cover, front compartment main wire and service plug grip not installed 11 to 14 V
A17-2 (FSDN) - A17-4 (E1) FC emergency shutdown signal Ignition switch ON (READY) 0 to 1.5 V
A16-20 (ISDN) - A17-4 (E1) Boosting converter (EV) fail signal Ignition switch ON (READY) 0 to 1.5 V
A15-7 (SILK) - A17-4 (E1) FC interlock switch FC converter power outlet cable installed 0 to 1.5 V
A16-6 (FRP) - A17-4 (E1) FC precharge junction assembly (FRP) operation signal Ignition switch ON→Ignition switch ON (READY) Pulse generation
(Waveform 10)
A16-3 (FRB+) - A16-5 (FRB-) FC stack main relay (FRB) operation signal Ignition switch ON→Ignition switch ON (READY) Pulse generation
(Waveform 10)
A15-3 (FRG+) - A15-2 (FRG-) FC stack main relay (FRG) operation signal Ignition switch ON→Ignition switch ON (READY) Pulse generation
(Waveform 10)
A8-22 (ABFS) - A17-4 (E1)*1
D15-22 (ABFS) - A17-4 (E1)*2
Airbag activation signal Ignition switch ON (READY) Pulse generation
(Waveform 11)
A8-17 (CA1L) - A17-4 (E1)*1
D15-17 (CA1L) - A17-4 (E1)*2
CAN communication signal Ignition switch ON Pulse generation
(Waveform 12)
A8-16 (CA1H) - A17-4 (E1)*1
D15-16 (CA1H) - A17-4 (E1)*2
CAN communication signal Ignition switch ON Pulse generation
(Waveform 12)
A8-15 (CA3N) - A17-4 (E1)*1
D15-15 (CA3N) - A17-4 (E1)*2
CAN communication signal Ignition switch ON Pulse generation
(Waveform 13)
A8-14 (CA3P) - A17-4 (E1)*1
D15-14 (CA3P) - A17-4 (E1)*2
CAN communication signal Ignition switch ON Pulse generation
(Waveform 13)
A8-2 (CA4H) - A17-4 (E1)*1
D15-2 (CA4H) - A17-4 (E1)*2
CAN communication signal Ignition switch ON Pulse generation
(Waveform 14)
A8-3 (CA4L) - A17-4 (E1)*1
D15-3 (CA4L) - A17-4 (E1)*2
CAN communication signal Ignition switch ON Pulse generation
(Waveform 14)
A16-22 (DRN3) - Body ground Shield ground Always Below 1 Ω
A17-4 (E1) - Body ground Ground Always Below 1 Ω
A15-35 (EC1) - Body ground Ground Always Below 1 Ω
A17-32 (EC2) - Body ground Ground Always Below 1 Ω
A17-3 (E01) - Body ground Ground Always Below 1 Ω
A8-5 (E02) - Body ground*1
D15-5 (E02) - Body ground*2
Ground Always Below 1 Ω
A8-4 (E12) - Body ground*1
D15-4 (E12) - Body ground*2
Ground Always Below 1 Ω

a.

Oscilloscope waveforms

HINT:

Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.


i.
C206009N09
2.969,0.875 3.302,1.073 0.333,0.198 10 false GND 2.969,1.448 3.302,1.646 0.333,0.198 10 false GND 0.208,0.646 0.542,0.844 0.333,0.198 10 false CH1 0.208,1.26 0.542,1.458 0.333,0.198 10 false CH2

Waveform 1 (Oil with pump motor signal)

for LHD:
Item Content
Terminal CH1: G14-15 (OPM1) - A17-4 (E1)
CH2: G14-10 (NOPM) - A17-4 (E1)
Equipment Setting 10 V/DIV., 20 ms/DIV
Condition Ignition switch ON (READY)

for RHD:
Item Content
Terminal CH1: A14-15 (OPM1) - A17-4 (E1)
CH2: A14-10 (NOPM) - A17-4 (E1)
Equipment Setting 10 V/DIV., 20 ms/DIV
Condition Ignition switch ON (READY)


ii.
A415999E05
0.365,0.854 0.823,1.052 0.458,0.198 10 false CH1 0.375,1.417 0.833,1.615 0.458,0.198 10 false CH2 2.958,1.635 3.281,1.917 0.323,0.281 10 false GND 2.958,0.854 3.281,1.135 0.323,0.281 10 false GND

Waveform 2 (Water with motor pump signal)

Item Content
Terminal CH1: A17-30 (IWP) - A17-4 (E1)
CH2: A17-10 (NIWP) - A17-4 (E1)
Equipment Setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON (READY)


iii.
A141395E10
3.104,0.99 3.417,1.229 0.313,0.24 10 GND

Waveform 3 (DC/DC operation monitor/voltage change signal)

Item Content
Terminal A17-17 (VLO) - A17-4 (E1)
Equipment Setting 5 V/DIV., 50 ms./DIV.
Condition Ignition switch ON

HINT:

The cycle will vary depending on the specified voltage of the DC/DC converter.



iv.
A298833N01
2.854,1.156 3.219,1.344 0.365,0.188 10 GND 2.844,1.615 3.208,1.802 0.365,0.188 10 GND 0.208,0.583 0.521,0.781 0.313,0.198 10 CH1 0.208,1.146 0.521,1.344 0.313,0.198 10 CH2

Waveform 4 (Communication signal from MG ECU to EV control ECU)

Item Content
Terminal CH1: A16-16 (MTH+) - A17-4 (E1)
CH2: A16-17 (MTH-) - A17-4 (E1)
Equipment Setting 1 V/DIV., 200 μs./DIV.
Condition Ignition switch ON (READY)

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



v.
A298833N01
2.854,1.156 3.219,1.344 0.365,0.188 10 GND 2.844,1.615 3.208,1.802 0.365,0.188 10 GND 0.208,0.583 0.521,0.781 0.313,0.198 10 CH1 0.208,1.146 0.521,1.344 0.313,0.198 10 CH2

Waveform 6 (Communication signal from EV control ECU to MG ECU)

Item Content
Terminal CH1: A16-10 (HTM+) - A17-4 (E1)
CH2: A16-11 (HTM-) - A17-4 (E1)
Equipment Setting 1 V/DIV., 200 μs./DIV.
Condition Ignition switch ON (READY)

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



vi.
A298834N01
3,1.063 3.333,1.25 0.333,0.188 10 GND 2.99,1.625 3.323,1.813 0.333,0.188 10 GND 0.354,0.74 0.813,0.938 0.458,0.198 10 CH1 0.354,1.479 0.813,1.677 0.458,0.198 10 CH2

Waveform 6 (MG ECU communication request signal)

Item Content
Terminal CH1: A16-14 (REQ+) - A17-4 (E1)
CH2: A16-15 (REQ-) - A17-4 (E1)
Equipment Setting 1 V/DIV., 1 ms./DIV.
Condition Ignition switch ON (READY)


vii.
A298834N01
3,1.063 3.333,1.25 0.333,0.188 10 GND 2.99,1.625 3.323,1.813 0.333,0.188 10 GND 0.354,0.74 0.813,0.938 0.458,0.198 10 CH1 0.354,1.479 0.813,1.677 0.458,0.198 10 CH2

Waveform 7 (MG communication clock signal)

Item Content
Terminal CH1: A16-12 (CLK+) - A17-4 (E1)
CH2: A16-13 (CLK-) - A17-4 (E1)
Equipment Setting 1 V/DIV., 1 μs./DIV.
Condition Ignition switch ON (READY)


viii.
C206010E22
0.26,0.552 0.708,0.719 0.448,0.167 10 CH1 0.26,0.906 0.708,1.115 0.448,0.208 10 CH2 0.26,1.354 0.656,1.531 0.396,0.177 10 CH3 2.969,0.677 3.375,0.844 0.406,0.167 10 GND 2.969,1.063 3.354,1.229 0.385,0.167 10 GND 2.969,1.448 3.354,1.625 0.385,0.177 10 GND

Waveform 8 (System main relay operation signal)

for LHD:
Item Content
Terminal CH1: G14-14 (SMRP) - A17-3 (E01)
CH2: G14-4 (SMRB) - A17-3 (E01)
CH3: G14-2 (SMRG) - A17-3 (E01)
Equipment Setting 10 V/DIV., 200 ms./DIV.
Condition Ignition switch ON→Ignition switch ON (READY)

for RHD:
Item Content
Terminal CH1: A14-14 (SMRP) - A17-3 (E01)
CH2: A14-4 (SMRB) - A17-3 (E01)
CH3: A14-2 (SMRG) - A17-3 (E01)
Equipment Setting 10 V/DIV., 200 ms./DIV.
Condition Ignition switch ON→Ignition switch ON (READY)

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



ix.
C372249E03
3.052,1.219 3.427,1.417 0.375,0.198 10 false GND

Waveform 9 (Electronic shift lever system fail-safe signal)

for LHD:
Item Content
Terminal A8-10 (SBFS) - A17-4 (E1)
Equipment Setting 10 V/DIV., 20 ms./DIV.
Condition Ignition switch ON

for RHD:
Item Content
Terminal D15-10 (SBFS) - A17-4 (E1)
Equipment Setting 10 V/DIV., 20 ms./DIV.
Condition Ignition switch ON

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



x.
C206010N06
0.26,0.552 0.708,0.719 0.448,0.167 10 CH1 0.26,0.906 0.708,1.115 0.448,0.208 10 CH2 0.26,1.354 0.656,1.531 0.396,0.177 10 CH3 2.969,0.677 3.375,0.844 0.406,0.167 10 GND 2.969,1.063 3.354,1.229 0.385,0.167 10 GND 2.969,1.448 3.354,1.625 0.385,0.177 10 GND

Waveform 10 (FC stack main relay, FC precharge junction assembly operation signal)

Item Content
Terminal CH1: A16-6 (FRP) - A17-4 (E1)
CH2: A16-3 (FRB+) - A16-5 (FRB-)
CH3: A15-3 (FRG+) - A15-2 (FRG-)
Equipment Setting 10 V/DIV., 200 ms/DIV.
Condition Ignition switch ON→Ignition switch ON (READY)


xi.
A298836N01
3.01,1.052 3.396,1.25 0.385,0.198 10 GND

Waveform 11 (Airbag activation signal)

for LHD:
Item Content
Terminal A8-22 (ABFS) - A17-4 (E1)
Equipment Setting 5 V/DIV., 150 ms./DIV.
Condition Ignition switch ON (READY)

for RHD:
Item Content
Terminal D15-22 (ABFS) - A17-4 (E1)
Equipment Setting 5 V/DIV., 150 ms./DIV.
Condition Ignition switch ON (READY)


xii.
A298838N01
3.01,1.229 3.375,1.469 0.365,0.24 10 GND 3.031,1.604 3.396,1.844 0.365,0.24 10 GND 0.302,0.865 0.667,1.104 0.365,0.24 10 CH1 0.323,1.427 0.688,1.667 0.365,0.24 10 CH2

Waveform 12 (CAN communication signal)

for LHD:
Item Content
Terminal CH1: A8-16 (CA1H) - A17-4 (E1)
CH2: A8-17 (CA1L) - A17-4 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Ignition switch ON

for RHD:
Item Content
Terminal CH1: D15-16 (CA1H) - A17-4 (E1)
CH2: D15-17 (CA1L) - A17-4 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



xiii.
A298838N01
3.01,1.229 3.375,1.469 0.365,0.24 10 GND 3.031,1.604 3.396,1.844 0.365,0.24 10 GND 0.302,0.865 0.667,1.104 0.365,0.24 10 CH1 0.323,1.427 0.688,1.667 0.365,0.24 10 CH2

Waveform 13 (CAN communication signal)

for LHD:
Item Content
Terminal CH1: A8-14 (CA3P) - A17-4 (E1)
CH2: A8-15 (CA3N) - A17-4 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Ignition switch ON

for RHD:
Item Content
Terminal CH1: D15-14 (CA3P) - A17-4 (E1)
CH2: D15-15 (CA3N) - A17-4 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



xiv.
A298838E03
3.01,1.229 3.375,1.469 0.365,0.24 10 GND 3.031,1.604 3.396,1.844 0.365,0.24 10 GND 0.302,0.865 0.667,1.104 0.365,0.24 10 CH1 0.323,1.427 0.688,1.667 0.365,0.24 10 CH2

Waveform 14 (CAN communication signal)

for LHD:
Item Content
Terminal CH1: A8-2 (CA4H) - A17-4 (E1)
CH2: A8-3 (CA4L) - A17-4 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Ignition switch ON

for RHD:
Item Content
Terminal CH1: D15-2 (CA4H) - A17-4 (E1)
CH2: D15-3 (CA4L) - A17-4 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).





Inverter with Converter Assembly


C257881C17
1.698,0.219 2.167,0.542 0.469,0.323 5.188,0.5 5.656,0.823 0.469,0.323 2.792,0.219 3.26,0.542 0.469,0.323 0.115,0.052 0.333,0.271 0.219,0.219 12 false *a 1.823,0.302 2.104,0.479 0.281,0.177 10 false A19 5.302,0.594 5.656,0.813 0.354,0.219 10 false A20 2.917,0.302 3.198,0.479 0.281,0.177 10 false A18 2.208,0.229 2.49,0.406 0.281,0.177 10 false *A 3.313,0.24 3.594,0.417 0.281,0.177 10 false *B
*A for LHD *B for RHD
*a Inverter with Converter Assembly - -


HINT:

Since the inverter with converter assembly uses waterproof connectors, the voltage and waveforms cannot be inspected directly. Standard voltage readings and waveforms are indicated for reference only.


for LHD:
Terminal No.
(Symbol)
Terminal Description Condition Standard Condition
A19-2 (MTH-) - A19-30 (GND1) Communication signal from MG ECU to EV control ECU Ignition switch ON (READY) Pulse generation
(Waveform 2)
A19-3 (MTH+) - A19-30 (GND1) Communication signal from EV control ECU to MG ECU Ignition switch ON (READY) Pulse generation
(Waveform 2)
A19-10 (+B) - A19-30 (GND1) MG ECU power source Ignition switch ON 11 to 14 V
A19-11 (+B2) - A19-30 (GND1) MG ECU power source Ignition switch ON 11 to 14 V
A19-13 (CLK-) - A19-30 (GND1) MG ECU communication clock signal Ignition switch ON (READY) Pulse generation
(Waveform 1)
A19-14 (CLK+) - A19-30 (GND1) MG ECU communication clock signal Ignition switch ON (READY) Pulse generation
(Waveform 1)
A19-17 (GCS) - A19-6 (GCSG) FC air compressor motor resolver signal FC air compressor motor resolver running Pulse generation
(Waveform 5)
A19-18 (GSN) - A19-7 (GSNG) FC air compressor motor resolver signal FC air compressor motor resolver running Pulse generation
(Waveform 5)
A19-20 (GRF) - A19-9 (GRFG) FC air compressor motor resolver signal FC air compressor motor resolver running Pulse generation
(Waveform 5)
A19-22 (HTM-) - A19-30 (GND1) Communication signal from EV control ECU to MG ECU Ignition switch ON (READY) Pulse generation
(Waveform 3)
A19-23 (HTM+) - A19-30 (GND1) Communication signal from EV control ECU to MG ECU Ignition switch ON (READY) Pulse generation
(Waveform 3)
A19-24 (ILKO) - A19-30 (GND1) Interlock switch signal Ignition switch ON, connector cover assembly, inverter terminal cover, front compartment main wire and service plug grip installed correctly Below 1 V
Ignition switch ON, connector cover assembly, inverter terminal cover, front compartment main wire and service plug grip not installed 11 to 14 V
A19-25 (HSDN) - A19-30 (GND1) MG shutdown signal Ignition switch ON (READY) 0 to 1 V
A19-33 (REQ-) - A19-30 (GND1) MG ECU communication request signal Ignition switch ON (READY) Pulse generation
(Waveform 4)
A19-34 (REQ+) - A19-30 (GND1) MG ECU communication request signal Ignition switch ON (READY) Pulse generation
(Waveform 4)
A19-35 (ILKI) - A19-30 (GND1) Interlock switch signal Ignition switch ON, connector cover assembly, inverter terminal cover, front compartment main wire and service plug grip installed correctly Below 1 V
Ignition switch ON, connector cover assembly, inverter terminal cover, front compartment main wire and service plug grip not installed 11 to 14 V
A19-38 (MCS) - A19-27 (MCSG) Drive motor resolver signal Drive motor resolver running Pulse generation
(Waveform 6)
A19-39 (MSN) - A19-28 (MSNG) Drive motor resolver signal Drive motor resolver running Pulse generation
(Waveform 6)
A19-40 (MRF) - A19-29 (MRFG) Drive motor resolver signal Drive motor resolver running Pulse generation
(Waveform 6)
A20-1 (IGCT) - A19-30 (GND1) MG ECU power source Ignition switch ON 11 to 14 V
A20-2 (IDH) - A19-30 (GND1) Heater prohibit signal Ignition switch ON 4 to 6 V
A20-3 (S) - A19-30 (GND1) Auxiliary battery voltage monitor Ignition switch ON 11 to 14 V
A20-5 (NODD) - A19-30 (GND1) DC/DC operation DC/DC converter operating normally 5 to 7 V
DC/DC converter not operating normally 2 to 4 V
DC/DC converter operation prohibited 0.1 to 0.5 V
A20-6 (VLO) - A19-30 (GND1) DC/DC operation monitor / voltage change signal Ignition switch ON Pulse generation
(Waveform 7)

for RHD:
Terminal No.
(Symbol)
Terminal Description Condition Standard Condition
A18-2 (MTH-) - A18-30 (GND1) Communication signal from MG ECU to EV control ECU Ignition switch ON (READY) Pulse generation
(Waveform 2)
A18-3 (MTH+) - A18-30 (GND1) Communication signal from EV control ECU to MG ECU Ignition switch ON (READY) Pulse generation
(Waveform 2)
A18-10 (+B) - A18-30 (GND1) MG ECU power source Ignition switch ON 11 to 14 V
A18-11 (+B2) - A18-30 (GND1) MG ECU power source Ignition switch ON 11 to 14 V
A18-13 (CLK-) - A18-30 (GND1) MG ECU communication clock signal Ignition switch ON (READY) Pulse generation
(Waveform 1)
A18-14 (CLK+) - A18-30 (GND1) MG ECU communication clock signal Ignition switch ON (READY) Pulse generation
(Waveform 1)
A18-17 (GCS) - A18-6 (GCSG) FC air compressor motor resolver signal FC air compressor motor resolver running Pulse generation
(Waveform 5)
A18-18 (GSN) - A18-7 (GSNG) FC air compressor motor resolver signal FC air compressor motor resolver running Pulse generation
(Waveform 5)
A18-20 (GRF) - A18-9 (GRFG) FC air compressor motor resolver signal FC air compressor motor resolver running Pulse generation
(Waveform 5)
A18-22 (HTM-) - A18-30 (GND1) Communication signal from EV control ECU to MG ECU Ignition switch ON (READY) Pulse generation
(Waveform 3)
A18-23 (HTM+) - A18-30 (GND1) Communication signal from EV control ECU to MG ECU Ignition switch ON (READY) Pulse generation
(Waveform 3)
A18-24 (ILKO) - A18-30 (GND1) Interlock switch signal Ignition switch ON, connector cover assembly, inverter terminal cover, front compartment main wire and service plug grip installed correctly Below 1 V
Ignition switch ON, connector cover assembly, inverter terminal cover, front compartment main wire and service plug grip not installed 11 to 14 V
A18-25 (HSDN) - A18-30 (GND1) MG shutdown signal Ignition switch ON (READY) 0 to 1 V
A18-33 (REQ-) - A18-30 (GND1) MG ECU communication request signal Ignition switch ON (READY) Pulse generation
(Waveform 4)
A18-34 (REQ+) - A18-30 (GND1) MG ECU communication request signal Ignition switch ON (READY) Pulse generation
(Waveform 4)
A18-35 (ILKI) - A18-30 (GND1) Interlock switch signal Ignition switch ON, connector cover assembly, inverter terminal cover, front compartment main wire and service plug grip installed correctly Below 1 V
Ignition switch ON, connector cover assembly, inverter terminal cover, front compartment main wire and service plug grip not installed 11 to 14 V
A18-38 (MCS) - A18-27 (MCSG) Drive motor resolver signal Drive motor resolver running Pulse generation
(Waveform 6)
A18-39 (MSN) - A18-28 (MSNG) Drive motor resolver signal Drive motor resolver running Pulse generation
(Waveform 6)
A18-40 (MRF) - A18-29 (MRFG) Drive motor resolver signal Drive motor resolver running Pulse generation
(Waveform 6)
A20-1 (IGCT) - A18-30 (GND1) MG ECU power source Ignition switch ON 11 to 14 V
A20-2 (IDH) - A18-30 (GND1) Heater prohibit signal Ignition switch ON 4 to 6 V
A20-3 (S) - A18-30 (GND1) Auxiliary battery voltage monitor Ignition switch ON 11 to 14 V
A20-5 (NODD) - A18-30 (GND1) DC/DC operation DC/DC converter operating normally 5 to 7 V
DC/DC converter not operating normally 2 to 4 V
DC/DC converter operation prohibited 0.1 to 0.5 V
A20-6 (VLO) - A18-30 (GND1) DC/DC operation monitor / voltage change signal Ignition switch ON Pulse generation
(Waveform 7)

NOTICE:

Do not measure the voltage or waveform on the sealed side of the inverter with converter assembly connector. Doing so may damage the connector because the connector is waterproof.


a.

Oscilloscope waveforms

HINT:

Oscilloscope waveforms shown in the illustrations are examples for reference only. Noise, chattering, etc. are not shown.


i.
A284432N03
2.948,1.021 3.406,1.219 0.458,0.198 10 GND 2.948,1.573 3.406,1.771 0.458,0.198 10 GND 0.396,0.698 0.854,0.896 0.458,0.198 10 CH1 0.385,1.458 0.844,1.656 0.458,0.198 10 CH2

Waveform 1 (MG ECU communication clock signal)

for LHD:
Item Content
Terminal CH1: A19-13 (CLK-) - A19-30 (GND1)
CH2: A19-14 (CLK+) - A19-30 (GND1)
Equipment Setting 1 V/DIV., 1 μs./DIV.
Condition Ignition switch ON (READY)

for RHD:
Item Content
Terminal CH1: A18-13 (CLK-) - A18-30 (GND1)
CH2: A18-14 (CLK+) - A18-30 (GND1)
Equipment Setting 1 V/DIV., 1 μs./DIV.
Condition Ignition switch ON (READY)


ii.
A284433N04
2.833,1.01 3.292,1.208 0.458,0.198 10 GND 2.833,1.573 3.292,1.771 0.458,0.198 10 GND 0.26,0.531 0.719,0.729 0.458,0.198 10 CH1 0.26,1.177 0.719,1.375 0.458,0.198 10 CH2

Waveform 2 (Communication signal from MG ECU to EV control ECU)

for LHD:
Item Content
Terminal CH1: A19-2 (MTH-) - A19-30 (GND1)
CH2: A19-3 (MTH+) - A19-30 (GND1)
Equipment Setting 1 V/DIV., 200 μs./DIV.
Condition Ignition switch ON (READY)

for RHD:
Item Content
Terminal CH1: A18-2 (MTH-) - A18-30 (GND1)
CH2: A18-3 (MTH+) - A18-30 (GND1)
Equipment Setting 1 V/DIV., 200 μs./DIV.
Condition Ignition switch ON (READY)

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



iii.
A284433N04
2.833,1.01 3.292,1.208 0.458,0.198 10 GND 2.833,1.573 3.292,1.771 0.458,0.198 10 GND 0.26,0.531 0.719,0.729 0.458,0.198 10 CH1 0.26,1.177 0.719,1.375 0.458,0.198 10 CH2

Waveform 3 (Communication signal from EV control ECU to MG ECU)

for LHD:
Item Content
Terminal CH1: A19-22 (HTM-) - A19-30 (GND1)
CH2: A19-23 (HTM+) - A19-30 (GND1)
Equipment Setting 1 V/DIV., 200 μs./DIV.
Condition Ignition switch ON (READY)

for RHD:
Item Content
Terminal CH1: A18-22 (HTM-) - A18-30 (GND1)
CH2: A18-23 (HTM+) - A18-30 (GND1)
Equipment Setting 1 V/DIV., 200 μs./DIV.
Condition Ignition switch ON (READY)

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



iv.
A284434N03
2.927,1.573 3.385,1.771 0.458,0.198 10 GND 2.927,1.01 3.385,1.208 0.458,0.198 10 GND 0.365,0.51 0.823,0.708 0.458,0.198 10 CH1 0.375,1.229 0.833,1.427 0.458,0.198 10 CH2

Waveform 4 (MG ECU communication request signal)

for LHD:
Item Content
Terminal CH1: A19-33 (REQ-) - A19-30 (GND1)
CH2: A19-34 (REQ+) - A19-30 (GND1)
Equipment Setting 1 V/DIV., 1 ms./DIV.
Condition Ignition switch ON (READY)

for RHD:
Item Content
Terminal CH1: A18-33 (REQ-) - A18-30 (GND1)
CH2: A18-34 (REQ+) - A18-30 (GND1)
Equipment Setting 1 V/DIV., 1 ms./DIV.
Condition Ignition switch ON (READY)


v.
A284439N02
2.969,1.135 3.427,1.333 0.458,0.198 10 GND 2.969,0.656 3.427,0.854 0.458,0.198 10 GND 2.969,1.417 3.427,1.615 0.458,0.198 10 GND 0.375,0.688 0.833,0.885 0.458,0.198 10 CH1 0.375,1.135 0.833,1.333 0.458,0.198 10 CH2 0.375,1.417 0.833,1.615 0.458,0.198 10 CH3 1.208,1.667 1.365,1.865 0.156,0.198 10 A

Waveform 5 (FC air compressor motor resolver signal)

for LHD:
Item Content
Terminal CH1: A19-20 (GRF) - A19-9 (GRFG)
CH2: A19-18 (GSN) - A19-7 (GSNG)
CH3: A19-17 (GCS) - A19-6 (GCSG)
Equipment Setting CH1: 10 V/DIV., 1 ms./DIV.
CH2, 3: 5 V/DIV., 1 ms./DIV.
Condition FC Air Compressor Motor resolver running

for RHD:
Item Content
Terminal CH1: A18-20 (GRF) - A18-9 (GRFG)
CH2: A18-18 (GSN) - A18-7 (GSNG)
CH3: A18-17 (GCS) - A18-6 (GCSG)
Equipment Setting CH1: 10 V/DIV., 1 ms./DIV.
CH2, 3: 5 V/DIV., 1 ms./DIV.
Condition FC Air Compressor Motor resolver running

HINT:

Pulse cycle A becomes shorter as the rotor speed increases.



vi.
A284439N02
2.969,1.135 3.427,1.333 0.458,0.198 10 GND 2.969,0.656 3.427,0.854 0.458,0.198 10 GND 2.969,1.417 3.427,1.615 0.458,0.198 10 GND 0.375,0.688 0.833,0.885 0.458,0.198 10 CH1 0.375,1.135 0.833,1.333 0.458,0.198 10 CH2 0.375,1.417 0.833,1.615 0.458,0.198 10 CH3 1.208,1.667 1.365,1.865 0.156,0.198 10 A

Waveform 6 (Drive motor resolver signal)

for LHD:
Item Content
Terminal CH1: A19-40 (MRF) - A19-29 (MRFG)
CH2: A19-39 (MSN) - A19-28 (MSNG)
CH3: A19-38 (MCS) - A19-27 (MCSG)
Equipment Setting CH1: 10 V/DIV., 1 ms./DIV.
CH2, 3: 5 V/DIV., 1 ms./DIV.
Condition Motor resolver running

for RHD:
Item Content
Terminal CH1: A18-40 (MRF) - A18-29 (MRFG)
CH2: A18-39 (MSN) - A18-28 (MSNG)
CH3: A18-38 (MCS) - A18-27 (MCSG)
Equipment Setting CH1: 10 V/DIV., 1 ms./DIV.
CH2, 3: 5 V/DIV., 1 ms./DIV.
Condition Motor resolver running

HINT:

Pulse cycle A becomes shorter as the rotor speed increases.



vii.
A141395E11
3.104,0.99 3.417,1.229 0.313,0.24 10 GND

Waveform 7 (DC/DC operation monitor/voltage change signal)

Item Content
Terminal A20-6 (VLO) - A19-30 (GND1)
Equipment Setting 5 V/DIV., 50 ms./DIV.
Condition Ignition switch ON

HINT:

The cycle will vary depending on the specified voltage of the DC/DC converter.