Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0455055 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Blower Motor Circuit  


DESCRIPTION

The blower with fan motor sub-assembly reads the signal from the air conditioning amplifier assembly and controls operation and speed changes of the blower motor.

If the blower air volume is weak, or there are any other blower malfunctions such as the temperature or air volume cannot be changed, the following causes are possible.

Symptom Factor
Blower airflow volume cannot be changed
·

Air conditioning amplifier assembly malfunction

·

Blower with fan motor sub-assembly malfunction

·

Wire harness or connector



WIRING DIAGRAM

E316644E33
5.167,0.75 5.625,0.948 0.458,0.198 10 false BLW 4.875,0.75 5.333,0.948 0.458,0.198 10 false 21 5.177,1.521 5.635,1.719 0.458,0.198 10 false GND 4.854,1.406 5.313,1.604 0.458,0.198 10 false 17 6.073,0.875 6.531,1.073 0.458,0.198 10 false IC 2.563,0.615 3.021,0.813 0.458,0.198 10 false HTR 3.604,0.479 4.969,0.688 1.365,0.208 10 false from Auxiliary Battery 1.219,0.875 1.677,1.073 0.458,0.198 10 false IC 1.833,0.365 2.292,0.563 0.458,0.198 10 false +B 2.125,0.365 2.583,0.563 0.458,0.198 10 false 3 1.854,0.76 2.313,0.958 0.458,0.198 10 false SI 2.125,0.75 2.583,0.948 0.458,0.198 10 false 2 2.125,1.156 2.583,1.354 0.458,0.198 10 false 1 1.688,1.156 2.146,1.354 0.458,0.198 10 false GND 0.292,1.927 0.75,2.125 0.458,0.198 10 false A13 0.292,2.094 2.865,2.344 2.573,0.25 10 false Blower with Fan Motor Sub-assembly 4.667,1.958 5.125,2.156 0.458,0.198 10 false D81 4.667,2.104 7.042,2.323 2.375,0.219 10 false Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (BLOWER MOTOR)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Blower Motor Blower with fan motor sub-assembly Min.: 0
Max.: 31
-
Body Electrical > Air Conditioner > Active Test
Tester Display
Blower Motor
50004 121 2

Result:
Result Proceed to
Blower motor with fan sub-assembly does not operate A
Blower motor with fan sub-assembly operates but does not change speed B



A

2.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR SUB-ASSEMBLY - BATTERY AND BODY GROUND)

B

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the blower with fan motor sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A13)Location & Routing

Click Connector(A13)Instrument Panel>Front Compartment Main Wire>Blower Motor with Fan Sub-Assembly

A13-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A13)Location & Routing

Click Connector(A13)Instrument Panel>Front Compartment Main Wire>Blower Motor with Fan Sub-Assembly

A13-3 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER WITH FAN MOTOR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER WITH FAN MOTOR SUB-ASSEMBLY)
a.

Disconnect the D81 air conditioning amplifier assembly connector.


b.

Disconnect the A13 blower with fan motor sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D81,A13)Location & Routing

Click Connector(D81)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assembly

Click Connector(A13)Instrument Panel>Front Compartment Main Wire>Blower Motor with Fan Sub-Assembly

D81-21 (BLW) - A13-2 (SI) Always Below 1 Ω
D81-21 (BLW) or A13-2 (SI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK BLOWER WITH FAN MOTOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK BLOWER WITH FAN MOTOR SUB-ASSEMBLY
a.

Disconnect the D81 air conditioning amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D81)Location & Routing

Click Connector(D81)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assembly

D81-21 (BLW) - Body ground Always 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE BLOWER WITH FAN MOTOR SUB-ASSEMBLY

5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E349843C13
0.667,0.75 1.167,1 0.5,0.25 1.75,0.969 2,1.385 2,1.385 2.25,1.385 true 0.802,0.802 1.26,1 0.458,0.198 10 false A13 2.302,1.292 2.76,1.49 0.458,0.198 10 false SI 2.875,2.833 3.229,3.042 0.354,0.208 10 false GND 0.073,0.052 0.531,0.25 0.458,0.198 10 false *a
*a Component with harness connected
(Blower with Fan Motor Sub-assembly)


Using the oscilloscope, check for the waveform.

Terminal No. Tool Setting Condition
A13-2 (SI) - Body ground 1 V/DIV., 500 μs./DIV.
·

Ignition switch ON

·

Blower switch: LO



HINT:

The waveform varies with the blower speed.


OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE BLOWER WITH FAN MOTOR SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E457294C01
0.417,0.583 0.917,0.833 0.5,0.25 0.583,0.406 0.833,0.406 0.833,0.406 1.135,0.677 true 2.25,1.229 2,1.229 2,1.229 1.781,0.813 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 0.542,0.635 0.854,0.833 0.313,0.198 10 false D81 0.271,0.344 0.583,0.542 0.313,0.198 10 false GND 2.313,1.177 2.677,1.375 0.365,0.198 10 false BLW 3.042,2.625 3.406,2.823 0.365,0.198 10 false GND
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Using an oscilloscope, check the waveform.

Terminal No. Tool Setting Condition
D81-21 (BLW) - D81-17 (GND) 2 V/DIV., 1 ms./DIV.
·

Ignition switch ON

·

Blower speed: LO



OK:

Waveform is similar to that shown in the illustration.


HINT:

The waveform varies with the blower speed.



Result:
Proceed to
OK
NG



OK

REPLACE BLOWER WITH FAN MOTOR SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY