EV CONTROL ECU
| *A | for LHD | *B | for RHD |
| *1 | EV Control ECU | - | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
|
*1: for LHD *2: for RHD |
|||
| G14-3 (RLAC) - A17-4 (E1)*1
A14-3 (RLAC) - A17-4 (E1)*2 |
A/C relay operation signal | Ignition switch ON | 11 to 14 V |
| G14-5 (FILK) - A17-4 (E1)*1
A14-5 (FILK) - A17-4 (E1)*2 |
Fuel lid with motor lock assembly signal (interlock switch) | Fuel lid fully closed | 11 to 14 V |
| G14-6 (CAFH) - A17-4 (E1)*1
A14-6 (CAFH) - A17-4 (E1)*2 |
CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 1) |
| G14-7 (CAFL) - A17-4 (E1)*1
A14-7 (CAFL) - A17-4 (E1)*2 |
CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 1) |
| G14-8 (IGSW) - A17-4 (E1)*1
A14-8 (IGSW) - A17-4 (E1)*2 |
HF-B relay operation signal | Ignition switch ON | 11 to 14 V |
| G14-16 (VD3) - G14-33 (ED3)*1
A14-16 (VD3) - A14-33 (ED3)*2 |
Hydrogen detector (for hydrogen tank 3 side) power source | Ignition switch ON | 4.5 to 5.5 V |
| G14-17 (VDTN) - G14-34 (EDTN)*1
A14-17 (VDTN) - A14-34 (EDTN)*2 |
Hydrogen detector (for hydrogen tank 1, 2 side) power source | Ignition switch ON | 4.5 to 5.5 V |
| G14-23 (ICP) - G14-22 (GIC2)*1
A14-23 (ICP) - A14-22 (GIC2)*2 |
FC stack inlet air pressure sensor (vacuum sensor assembly) signal | Ignition switch ON | 0.3 to 3.6 V |
| G14-24 (VICP) - G14-22 (GIC2)*1
A14-24 (VICP) - A14-22 (GIC2)*2 |
Vacuum sensor assembly power source | Ignition switch ON | 4.5 to 5.5 V |
| G14-25 (ICT) - G14-22 (GIC2)*1
A14-25 (ICT) - A14-22 (GIC2)*2 |
FC stack inlet air temperature sensor (vacuum sensor assembly) signal | Ignition switch ON, FC stack inlet air temperature sensor temperature 20°C(68°F) | 4.3 to 4.7 V |
| G14-26 (HD3) - G14-33 (ED3)*1
A14-26 (HD3) - A14-33 (ED3)*2 |
Hydrogen detector (for hydrogen tank 3 side) signal | Ignition switch ON | Pulse generation
(Waveform 2) |
| G14-27 (HDTN) - G14-34 (EDTN)*1
A14-27 (HDTN) - A14-34 (EDTN)*2 |
Hydrogen detector (for hydrogen tank 1, 2 side) signal | Ignition switch ON | Pulse generation
(Waveform 3) |
| G14-32 (DRN6) - Body ground*1
A14-32 (DRN6) - Body ground*2 |
Shield ground | Always | Below 1 Ω |
| A15-1 (RLTN) - A17-4 (E1) | H2 SHUT VLV relay operation signal | Ignition switch ON (READY) | 11 to 15.5 V |
| A15-2 (FRG-) - A17-4 (E1) | FC relay (FRG) operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation |
| A15-3 (FRG+) - A17-4 (E1) | FC relay (FRG) operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation
(Waveform 4) |
| A15-5 (FTH+) - A15-6 (FTH-) | Communication signal from FC control ECU to EV control ECU | Ignition switch ON | Pulse generation
(Waveform 9) |
| A15-7 (SILK) - A17-4 (E1) | FC interlock switch | Each one of FC interlock circuit components installed correctly | Below 1 V |
| A15-8 (LIN2) - A17-4 (E1) | FC Hydrogen pump inverter assembly communication signal | Ignition switch ON | Pulse generation
(Waveform 10) |
| A15-9 (LIN1) - A17-4 (E1) | FC cooling water pump inverter assembly communication signal | Ignition switch ON | Pulse generation
(Waveform 11) |
| A15-10 (DRN7) - Body ground | Shield ground | Always | Below 1 Ω |
| A15-12 (FCSD) - A17-4 (E1) | FC control ECU emergency shutdown signal | Ignition switch ON (READY) | Below 1 V |
| A15-14 (HTF+) - A15-15 (HTF-) | Communication signal from EV control ECU to FC control ECU | Ignition switch ON | Pulse generation
(Waveform 12) |
| A15-16 (FCL+) - A15-17 (FCL-) | FC control ECU communication clock signal | Ignition switch ON | Pulse generation
(Waveform 13) |
| A15-18 (FRQ+) - A15-19 (FRQ-) | FC control ECU communication request signal | Ignition switch ON | Pulse generation
(Waveform 14) |
| A15-24 (WTO) - A15-32 (GWTO) | Water temperature sensor (for FC stack outlet side) signal | Ignition switch ON, water temperature sensor (for FC stack outlet side) temperature 20°C(68°F) | 2.1 to 2.7 V |
| A15-25 (WTR) - A15-33 (GWTR) | Water temperature sensor (for radiator outlet side) signal | Ignition switch ON, water temperature sensor (for radiator outlet side) temperature 20°C(68°F) | 2.1 to 2.7 V |
| A15-26 (HTM) - A15-34 (GHTM) | Hydrogen pump motor temperature sensor signal | Ignition switch ON, hydrogen pump motor temperature 20°C (68°F) | 4.2 to 4.6 V |
| A15-29 (WFN1) - A17-4 (E1) | Cooling fan controller with motor (for Fan Side) signal | Ignition switch ON, cooling fan controller with motor (for Fan Side) operated | Pulse generation
(Waveform 5) |
| A15-35 (EC1) - Body ground | Ground | Always | Below 1 Ω |
| A16-5 (FRB-) - A17-4 (E1) | FC relay (FRB) operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation
(Waveform 4) |
| A16-3 (FRB+) - A17-4 (E1) | FC relay (FRB) operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation |
| A16-6 (FRP) - A17-4 (E1) | FC relay (FRP) operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation
(Waveform 4) |
| A16-7 (IG2) - A17-4 (E1) | Power source | Ignition switch ON | 11 to 14 V |
| A16-20 (ISDN) - A17-4 (E1) | FC boost control ECU fail signal | Ignition switch ON (READY) | Below 1 V |
| A16-22 (DRN3) - Body ground | Shield ground | Always | Below 1 Ω |
| A16-25 (AFMF) - A16-23 (GAFM) | Mass air flow meter sub-assembly signal (air flow sensor) | Ignition switch ON | Pulse generation
(Waveform 6) |
| A16-26 (AFMT) - A16-23 (GAFM) | Mass air flow meter sub-assembly (intake air temperature sensor) signal | Ignition switch ON, intake air temperature 20°C (68°F) | 2.2 to 2.6 V |
| A16-27 (VAFF) - A16-23 (GAFM) | Mass air flow meter sub-assembly (air flow sensor) power source | Ignition switch ON | 11 to 14 V |
| A16-31 (HDMR) - A16-30 (EDMR) | Hydrogen detector (for front compartment side) signal | Ignition switch ON | Pulse generation
(Waveform 7) |
| A16-32 (VDMR) - A16-30 (EDMR) | Hydrogen detector (for front compartment side) signal power source | Ignition switch ON | 4.5 to 5.5 V |
| A17-1 (+B1) - A17-4 (E1) | Power source | Ignition switch ON | 11 to 14 V |
| A17-2 (FSDN) - A17-4 (E1) | FC boost control ECU emergency shutdown signal | Ignition switch ON (READY) | Below 1 V |
| A17-3 (E01) - Body ground | Ground | Always | Below 1 Ω |
| A17-4 (E1) - Body ground | Ground | Always | Below 1 Ω |
| A17-15 (HFCH) - A17-16 (HFCL) | FC boost control ECU communication signal | Ignition switch ON | Pulse generation
(Waveform 15) |
| A17-26 (DRN5) - Body ground | Shield ground | Always | Below 1 Ω |
| A17-32 (EC2) - Body ground | Ground | Always | Below 1 Ω |
| A8-1 (BATT) - A17-4 (E1)*1
D15-1 (BATT) - A17-4 (E1)*2 |
Constant power source | Always | 11 to 14 V |
| A8-4 (E12) - Body ground*1
D15-4 (E12) - Body ground*2 |
Ground | Always | Below 1 Ω |
| A8-5 (E02) - Body ground*1
D15-5 (E02) - Body ground*2 |
Ground | Always | Below 1 Ω |
| A8-7 (+B2) - A17-4 (E1)*1
D15-7 (+B2) - A17-4 (E1)*2 |
Power source | Ignition switch ON | 11 to 14 V |
| A8-11 (WDRN) - A17-4 (E1)*1
D15-11 (WDRN) - A17-4 (E1)*2 |
FC water release switch signal | Ignition switch ON, FC water release switch not operated | 11 to 14 V |
| Ignition switch ON, FC water release switch operated | 0 to 1.5 V | ||
| A8-16 (CA1H) - A17-4 (E1)*1
D15-16 (CA1H) - A17-4 (E1)*2 |
CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 8) |
| A8-17 (CA1L) - A17-4 (E1)*1
D15-17 (CA1L) - A17-4 (E1)*2 |
CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 8) |
| A8-21 (MREL) - A17-4 (E1)*1
D15-21 (MREL) - A17-4 (E1)*2 |
Main relay operation signal | Ignition switch ON | 11 to 14 V |
| A8-28 (LOSW) - A17-4 (E1)*1
D15-28 (LOSW) - A17-4 (E1)*2 |
Fuel lid opener switch signal | Fuel lid opener switch off | 11 to 14 V |
Oscilloscope waveforms
Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.
Waveform 1
| Item | Content |
|---|---|
| Terminal | CH1: CAFH - E1 |
| CH2: CAFL - E1 | |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 2
| Item | Content |
|---|---|
| Terminal | HD3 - ED3 |
| Equipment Setting | 5 V/DIV., 1 ms/DIV. |
| Condition | Ignition switch ON |
The duty ratio may vary depending on the conditions.
Waveform 3
| Item | Content |
|---|---|
| Terminal | HDTN - EDTN |
| Equipment Setting | 5 V/DIV., 1 ms/DIV. |
| Condition | Ignition switch ON |
The duty ratio may vary depending on the conditions.
Waveform 4
| Item | Content |
|---|---|
| Terminal | CH1: FRP - E1 |
| CH2: FRB+ - E1 | |
| CH3: FRG+ - E1 | |
| Equipment Setting | 10 V/DIV., 200 ms/DIV. |
| Condition | Ignition switch ON → Ignition switch ON (READY) |
Waveform 5
| Item | Content |
|---|---|
| Terminal | WFN1 - E1 |
| Equipment Setting | 1 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch ON, cooling fan controller with motor (for Fan Side) operated |
Waveform 6
| Item | Content |
|---|---|
| Terminal | AFMF - GAFM |
| Equipment Setting | 1 V/DIV., 100 μs/DIV. |
| Condition | Ignition switch ON |
Waveform 7
| Item | Content |
|---|---|
| Terminal | HDMR - EDMR |
| Equipment Setting | 5 V/DIV., 1 ms/DIV. |
| Condition | Ignition switch ON |
The duty ratio may vary depending on the conditions.
Waveform 8
| Item | Content |
|---|---|
| Terminal | CH1: CA1H - E1 |
| CH2: CA1L - E1 | |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 9
| Item | Content |
|---|---|
| Terminal | CH1: FTH+ - E1 |
| CH2: FTH- - E1 | |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 10
| Item | Content |
|---|---|
| Terminal | CH1: LIN2 - E1 |
| Equipment Setting | 2 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch ON |
Waveform 11
| Item | Content |
|---|---|
| Terminal | CH1: LIN1 - E1 |
| Equipment Setting | 2 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch ON |
Waveform 12
| Item | Content |
|---|---|
| Terminal | CH1: HTF+ - E1 |
| CH2: HTF- - E1 | |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
Waveform 13
| Item | Content |
|---|---|
| Terminal | CH1: FCL+ - FCL- |
| Equipment Setting | 1 V/DIV., 0.5 μs/DIV. |
| Condition | Ignition switch ON |
Waveform 14
| Item | Content |
|---|---|
| Terminal | CH1: FRQ+ - FRQ- |
| Equipment Setting | 2 V/DIV., 2 ms/DIV. |
| Condition | Ignition switch ON |
Waveform 15
| Item | Content |
|---|---|
| Terminal | CH1: HFCH - E1 |
| CH2: HFCL - E1 | |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
FC CONTROL ECU
| *1 | FC Control ECU | - | - |
Because the FC control ECU uses a waterproof connector, voltage, resistance, and waveform inspections are not possible. Voltage, resistance, and waveform information is included for reference.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B1-41 (VHVP) - B1-104 (E1) | Exhaust drainage valve actuation signal | Ignition switch ON (READY), exhaust drainage valve operated | Pulse generation
(Waveform 1) |
| B1-42 (VHI3) - B1-105 (E2) | No. 3 fuel injector assembly actuation signal | Ignition switch ON (READY), No. 3 fuel injector assembly operated | Pulse generation
(Waveform 2) |
| B1-43 (+B1) - B1-104 (E1) | Power source | Ignition switch ON | 11 to 14 V |
| B1-44 (VHI2) - B1-105 (E2) | No. 2 fuel injector assembly actuation signal | Ignition switch ON (READY), No. 2 fuel injector assembly operated | Pulse generation
(Waveform 3) |
| B1-46 (VHI1) - B1-105 (E2) | No. 1 fuel injector assembly actuation signal | Ignition switch ON (READY), No. 1 fuel injector assembly operated | Pulse generation
(Waveform 4) |
| B1-47 (FCK+) - B1-48 (FCK-) | EV control ECU communication clock signal | Ignition switch ON | Pulse generation
(Waveform 6) |
| B1-49 (DRN4) - Body ground | Shield ground | Always | Below 1 Ω |
| B1-50 (HTF+) - B1-51 (HTF-) | Communication signal from EV control ECU to FC control ECU | Ignition switch ON | Pulse generation
(Waveform 7) |
| B1-52 (DRN5) - Body ground | Shield ground | Always | Below 1 Ω |
| B1-53 (FTH+) - B1-54 (FTH-) | Communication signal from FC control ECU to EV control ECU | Ignition switch ON | Pulse generation
(Waveform 8) |
| B1-55 (DRN6) - Body ground | Shield ground | Always | Below 1 Ω |
| B1-56 (FRQ+) - B1-57 (FRQ-) | EV control ECU communication request signal | Ignition switch ON | Pulse generation
(Waveform 9) |
| B1-58 (DRN7) - Body ground | Shield ground | Always | Below 1 Ω |
| B1-62 (IG2) - B1-104 (E1) | Power source | Ignition switch ON | 11 to 14 V |
| B1-64 (CA1L) - B1-104 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 5) |
| B1-65 (CA1H) - B1-104 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 5) |
| B1-67 (HPL) - B1-66 (GHPL) | Hydrogen secondary pressure sensor signal | Ignition switch ON | 0.5 to 4.5 V |
| B1-68 (VHPL) - B1-66 (GHPL) | Hydrogen secondary pressure sensor power source | Ignition switch ON | 4.5 to 5.5 V |
| B1-72 (VAVP) - B1-73 (GAVP) | FC air pressure regulator assembly (air pressure regulating valve) opening angle sensor power source | Ignition switch ON | 4.5 to 5.5 V |
| B1-74 (AVP) - B1-73 (GAVP) | FC air pressure regulator assembly (air pressure regulating valve) opening angle sensor signal | Ignition switch ON, FC air pressure regulator assembly (air pressure regulating valve) fully closed | 0.604 to 0.776 V |
| Ignition switch ON (READY), FC air pressure regulator assembly (air pressure regulating valve) fully open | 3.432 to 4.588 V | ||
| B1-75 (DRN8) - Body ground | Shield ground | Always | Below 1 Ω |
| B1-77 (DRN0) - Body ground | Shield ground | Always | Below 1 Ω |
| B1-79 (FCSD) - B1-104 (E1) | FC control ECU emergency shutdown signal | Ignition switch ON (READY) | Below 1 V |
| B1-81 (HVP) - B1-104 (E1) | Exhaust drainage valve actuation signal | Ignition switch ON (READY), exhaust drainage valve operated | Pulse generation
(Waveform 1) |
| B1-82 (HIN3) - B1-105 (E2) | No. 3 fuel injector assembly actuation signal | Ignition switch ON (READY), No. 3 fuel injector assembly operated | Pulse generation
(Waveform 2) |
| B1-83 (+B2) - B1-104 (E1) | Power source | Ignition switch ON | 11 to 14 V |
| B1-84 (HIN2) - B1-105 (E2) | No. 2 fuel injector assembly actuation signal | Ignition switch ON (READY), No. 2 fuel injector assembly operated | Pulse generation
(Waveform 3) |
| B1-86 (HIN1) - B1-105 (E2) | No. 1 fuel injector assembly actuation signal | Ignition switch ON (READY), No. 1 fuel injector assembly operated | Pulse generation
(Waveform 4) |
| B1-89 (DRN3) - Body ground | Shield ground | Always | Below 1 Ω |
| B1-90 (DRN1) - Body ground | Shield ground | Always | Below 1 Ω |
| B1-95 (DRN2) - Body ground | Shield ground | Always | Below 1 Ω |
| B1-96 (DRN9) - Body ground | Shield ground | Always | Below 1 Ω |
| B1-97 (VASP) - B1-98 (GASP) | FC air pressure regulator assembly (air sealing valve) opening angle sensor power source | Ignition switch ON | 4.5 to 5.5 V |
| B1-99 (ASP) - B1-98 (GASP) | FC air pressure regulator assembly (air sealing valve) opening angle sensor signal | Ignition switch ON, FC air pressure regulator assembly (air sealing valve) fully closed | 0.604 to 0.776 V |
| Ignition switch ON (READY), FC air pressure regulator assembly (air sealing valve) fully open | 3.432 to 4.588 V | ||
| B1-104 (E1) - Body ground | Ground | Always | Below 1 Ω |
| B1-105 (E2) - Body ground | Ground | Always | Below 1 Ω |
| B1-110 (AMT) - B1-111 (GAMT) | FC air compressor motor temperature sensor signal | Ignition switch ON, temperature 25°C (77°F) | 3.6 to 4.6 V |
| Ignition switch ON, temperature 60°C (140°F) | 2.2 to 3.2 V | ||
| B1-112 (HPM) - B1-113 (GHPM) | Hydrogen primary pressure sensor signal | Ignition switch ON | 0.5 to 4.5 V |
| B1-114 (VHPM) - B1-113 (GHPM) | Hydrogen primary pressure sensor power source | Ignition switch ON | 4.5 to 5.5 V |
| B1-115 (VHPT) - B1-116 (GHPT) | Hydrogen tank pressure sensor (for outlet side) power source | Ignition switch ON | 4.5 to 5.5 V |
| B1-117 (HPT) - B1-116 (GHPT) | Hydrogen tank pressure sensor (for outlet side) signal | Ignition switch ON | 0.8 to 4.4 V |
| B1-118 (VABP) - B1-119 (GABP) | FC air by-pass valve assembly (air shunt valve) opening angle sensor power source | Ignition switch ON | 4.5 to 5.5 V |
| B1-120 (ABP) - B1-119 (GABP) | FC air by-pass valve assembly (air shunt valve) opening angle sensor signal | Ignition switch ON, FC air by-pass valve assembly (air shunt valve) fully closed | 0.604 to 0.776 V |
| Ignition switch ON (READY), FC air by-pass valve assembly (air shunt valve) fully open | 3.432 to 4.588 V | ||
| B1-121 (DRNA) - Body ground | Shield ground | Always | Below 1 Ω |
| A48-1 (AVV2) - B1-104 (E1) | FC air pressure regulator assembly (air pressure regulating valve) actuation signal | Ignition switch ON (READY), FC air pressure regulator assembly (air pressure regulating valve) operated | Pulse generation
(Waveform 10) |
| A48-2 (+BP3) - B1-104 (E1) | Power source | Ignition switch ON | 11 to 14 V |
| A48-3 (ASV1) - B1-104 (E1) | FC air pressure regulator assembly (air sealing valve) actuation signal | Ignition switch ON (READY), FC air pressure regulator assembly (air sealing valve) operated | Pulse generation
(Waveform 11) |
| A48-4 (WRB2) - B1-104 (E1) | FC cooling water temperature control valve actuation signal | Ignition switch ON (READY), FC cooling water temperature control valve operated | Pulse generation
(Waveform 13) |
| A48-5 (WRB1) - B1-104 (E1) | FC cooling water temperature control valve actuation signal | Ignition switch ON (READY), FC cooling water temperature control valve operated | Pulse generation
(Waveform 13) |
| A48-7 (WRA2) - B1-104 (E1) | FC cooling water temperature control valve actuation signal | Ignition switch ON (READY), FC cooling water temperature control valve operated | Pulse generation
(Waveform 13) |
| A48-8 (WRA1) - B1-104 (E1) | FC cooling water temperature control valve actuation signal | Ignition switch ON (READY), FC cooling water temperature control valve operated | Pulse generation
(Waveform 13) |
| A48-20 (AVV1) - B1-104 (E1) | FC air pressure regulator assembly (air pressure regulating valve) actuation signal | Ignition switch ON (READY), FC air pressure regulator assembly (air pressure regulating valve) operated | Pulse generation
(Waveform 10) |
| A48-21 (E03) - Body ground | Ground | Always | Below 1 Ω |
| A48-22 (ASV2) - B1-104 (E1) | FC air pressure regulator assembly (air sealing valve) actuation signal | Ignition switch ON (READY), FC air pressure regulator assembly (air sealing valve) operated | Pulse generation
(Waveform 11) |
| A48-32 (ABV1) - B1-104 (E1) | FC air by-pass valve assembly (air shunt valve) actuation signal | Ignition switch ON (READY), FC air by-pass valve assembly (air shunt valve) operated | Pulse generation
(Waveform 12) |
| A48-33 (ABV2) - B1-104 (E1) | FC air by-pass valve assembly (air shunt valve) actuation signal | Ignition switch ON (READY), FC air by-pass valve assembly (air shunt valve) operated | Pulse generation
(Waveform 12) |
| A48-53 (EC) - Body ground | Ground | Always | Below 1 Ω |
Oscilloscope waveforms
Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.
Waveform 1
| Item | Content |
|---|---|
| Terminal | CH1: VHVP - E1
CH2: HVP - E1 |
| Equipment Setting | 5 V/DIV., 100 ms/DIV. |
| Condition | Ignition switch ON (READY), exhaust drainage valve operated |
The waveform shown in the illustration may not be generated depending on the conditions.
The time in range A may vary depending on the conditions.
Waveform 2
| Item | Content |
|---|---|
| Terminal | CH1: VHI3 - E2
CH2: HIN3 - E2 |
| Equipment Setting | 10 V/DIV., 4 ms/DIV. |
| Condition | Ignition switch ON (READY), No. 3 fuel injector assembly operated |
The waveform shown in the illustration may not be generated depending on the conditions.
The time in range A may vary depending on the conditions.
Waveform 3
| Item | Content |
|---|---|
| Terminal | CH1: VHI2 - E2
CH2: HIN2 - E2 |
| Equipment Setting | 10 V/DIV., 4 ms/DIV. |
| Condition | Ignition switch ON (READY), No. 2 fuel injector assembly operated |
The waveform shown in the illustration may not be generated depending on the conditions.
The time in range A may vary depending on the conditions.
Waveform 4
| Item | Content |
|---|---|
| Terminal | CH1: VHI1 - E2
CH2: HIN1 - E2 |
| Equipment Setting | 10 V/DIV., 4 ms/DIV. |
| Condition | Ignition switch ON (READY), No. 1 fuel injector assembly operated |
The waveform shown in the illustration may not be generated depending on the conditions.
The time in range A may vary depending on the conditions.
Waveform 5
| Item | Content |
|---|---|
| Terminal | CH1: CA1H - E1
CH2: CA1L - E1 |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 6
| Item | Content |
|---|---|
| Terminal | CH1: FCK+ - FCK- |
| Equipment Setting | 1 V/DIV., 0.5 μs/DIV. |
| Condition | Ignition switch ON |
Waveform 7
| Item | Content |
|---|---|
| Terminal | CH1: HTF+ - E1
CH2: HTF- - E1 |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 8
| Item | Content |
|---|---|
| Terminal | CH1: FTH+ - E1
CH2: FTH- - E1 |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 9
| Item | Content |
|---|---|
| Terminal | CH1: FRQ+ - FRQ- |
| Equipment Setting | 1 V/DIV., 2 ms/DIV. |
| Condition | Ignition switch ON |
Waveform 10
| Item | Content |
|---|---|
| Terminal | CH1: AVV1 - E1
CH2: AVV2 - E1 |
| Equipment Setting | 5 V/DIV., 50 ms/DIV. |
| Condition | Ignition switch ON (READY), FC air pressure regulator assembly (air pressure regulating valve) operated |
A: Open side operates.
B: Close side operates.
Waveform 11
| Item | Content |
|---|---|
| Terminal | CH1: ASV1 - E1
CH2: ASV2 - E1 |
| Equipment Setting | 5 V/DIV., 50 ms/DIV. |
| Condition | Ignition switch ON (READY), FC air pressure regulator assembly (air sealing valve) operated |
A: Open side operates.
B: Close side operates.
Waveform 12
| Item | Content |
|---|---|
| Terminal | CH1: ABV1 - E1
CH2: ABV2 - E1 |
| Equipment Setting | 5 V/DIV., 50 ms/DIV. |
| Condition | Ignition switch ON (READY), FC air by-pass valve assembly (air shunt valve) operated |
A: Open side operates.
B: Close side operates.
Waveform 13
| Item | Content |
|---|---|
| Terminal | WRB1 - E1
WRA1 - E1 WRB2 - E1 WRA2 - E1 |
| Equipment Setting | 20 V/DIV., 10 ms/DIV. |
| Condition | Ignition switch ON (READY), FC cooling water temperature control valve operated |
HYDROGEN FUEL CONTROL ECU ASSEMBLY
| *1 | Hydrogen Fuel Control ECU Assembly | - | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| G4-1 (GTV3) - Body ground | Ground | Always | Below 1 Ω |
| G4-2 (TNV3) - G4-1 (GTV3) | Tank shut valve 3 actuation signal | Ignition switch ON (READY), tank shut valve 3 open | Pulse generation
(Waveform 1) |
| G4-3 (+BP2) - G4-32 (E1) | Tank shut valve 3 power source | Ignition switch ON (READY) | 11 to 14 V |
| G4-4 (VDR3) - Body ground | Shield ground | Always | Below 1 Ω |
| G4-7 (SEO) - G5-23 (GSEO) | Hydrogen fuel control transmitter signal | As fuel lid is opening | Pulse generation
(Waveform 2) |
| G4-9 (VSEO) - G4-23 (GSEO) | Hydrogen fuel control transmitter power source | Ignition switch ON | 4.9 to 5.8 V |
| G4-11 (VHPC) - G4-26 (GHPC) | Hydrogen tank pressure sensor (for inlet side) power source | Ignition switch ON | 4.75 to 5.25 V |
| G4-13 (CA1H) - G4-32 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 3) |
| G4-14 (CA1L) - G4-32 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 3) |
| G4-15 (CAFH) - G4-32 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 4) |
| G4-16 (CAFL) - G4-32 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 4) |
| G4-20 (RLLO) - G4-32 (E1) | FUEL LID OPN relay operation signal | Fuel lid opener switch off | 11 to 14 V |
| G4-24 (IDRN) - Body ground | Shield ground | Always | Below 1 Ω |
| G4-25 (SDRN) - Body ground | Shield ground | Always | Below 1 Ω |
| G4-27 (HPC) - G4-26 (GHPC) | Hydrogen tank pressure sensor (for inlet side) signal | Ignition switch ON | 0.5 to 4.8 V |
| G4-29 (TNT1) - G4-28 (GTT1) | Hydrogen tank temperature sensor 1 signal | Ignition switch ON | 1.0 to 2.8 V
(1.78 V (20°C (68°F)) |
| G4-30 (PDR2) - Body ground | Shield ground | Always | Below 1 Ω |
| G4-31 (TNT2) - G4-33 (GTT2) | Hydrogen tank temperature sensor 2 signal | Ignition switch ON | 1.0 to 2.8 V
(1.78 V (20°C (68°F)) |
| G4-32 (E1) - Body ground | Ground | Always | Below 1 Ω |
| G4-34 (TNT3) - G4-35 (GTT3) | Hydrogen tank temperature sensor 3 signal | Ignition switch ON | 1.0 to 2.8 V
(1.78 V (20°C (68°F)) |
| G4-38 (IGSW) - G4-32 (E1) | Power source | Ignition switch ON | 11 to 14 V |
| G5-1 (GTV1) - Body ground | Ground | Always | Below 1 Ω |
| G5-2 (GTV2) - Body ground | Ground | Always | Below 1 Ω |
| G5-4 (VDR2) - Body ground | Shield ground | Always | Below 1 Ω |
| G5-6 (TNV1) - G5-1 (GTV1) | Tank shut valve 1 actuation signal | Ignition switch ON (READY), tank shut valve 1 open | Pulse generation
(Waveform 5) |
| G5-7 (TNV2) - G5-2 (GTV2) | Tank shut valve 2 actuation signal | Ignition switch ON (READY), tank shut valve 2 open | Pulse generation
(Waveform 6) |
| G5-17 (PDR1) - Body ground | Shield ground | Always | Below 1 Ω |
| G5-18 (VDR1) - Body ground | Shield ground | Always | Below 1 Ω |
| G5-20 (+BP) - G4-32 (E1) | Tank shut valve 1, 2 power source | Ignition switch ON (READY) | 11 to 14 V |
Oscilloscope waveforms
Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.
Waveform 1
| Item | Content |
|---|---|
| Terminal | TNV3 - GTV3 |
| Equipment Setting | 5 V/DIV., 1 ms/DIV. |
| Condition | Ignition switch ON (READY), tank shut valve 3 open |
Waveform 2
| Item | Content |
|---|---|
| Terminal | SEO - GSEO |
| Equipment Setting | 1 V/DIV., 100 μs/DIV. |
| Condition | As fuel lid is opening |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 3
| Item | Content |
|---|---|
| Terminal | CH1: CA1H - E1
CH2: CA1L - E1 |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 4
| Item | Content |
|---|---|
| Terminal | CH1: CAFH - E1
CH2: CAFL - E1 |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 5
| Item | Content |
|---|---|
| Terminal | TNV1 - GTV1 |
| Equipment Setting | 5 V/DIV., 1 ms/DIV. |
| Condition | Ignition switch ON (READY), tank shut valve 1 open |
Waveform 6
| Item | Content |
|---|---|
| Terminal | TNV2 - GTV2 |
| Equipment Setting | 5 V/DIV., 1 ms/DIV. |
| Condition | Ignition switch ON (READY), tank shut valve 2 open |
FC BOOST CONTROL ECU
| *1 | FC Boost Control ECU | - | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B19-1 (FRG-) - B6-10 (E1) | FC relay (FRG) operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation |
| B19-2 (FRB-) - B6-10 (E1) | FC relay (FRB) operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation |
| B19-3 (FRP) - B6-10 (E1) | FC relay (FRP) operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation
(Waveform 1) |
| B19-7 (FRG+) - B6-10 (E1) | FC relay (FRG) operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation
(Waveform 1) |
| B19-8 (FRB+) - B6-10 (E1) | FC relay (FRB) operation signal | Ignition switch ON → Ignition switch ON (READY) | Pulse generation
(Waveform 1) |
| B19-10 (ILKI) - B6-10 (E1) | FC interlock switch | Each one of FC interlock circuit components installed correctly | Below 1 V |
| B19-13 (DRN2) - Body ground | Shield ground | Always | Below 1 Ω |
| B19-20 (HDCH) - B19-19 (HDCL) | EV control ECU communication signal | Ignition switch ON | Pulse generation
(Waveform 3) |
| B19-21 (CA1L) - B6-10 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 2) |
| B19-22 (CA1H) - B6-10 (E1) | CAN communication signal | Ignition switch ON | Pulse generation
(Waveform 2) |
| B6-1 (FSDN) - B6-10 (E1) | FC boost control ECU shutdown signal | Ignition switch ON (READY) | Below 1 V |
| B6-2 (DRN0) - Body ground | Shield ground | Always | Below 1 Ω |
| B6-4 (ISDN) - B6-10 (E1) | FC boost control ECU fail signal | Ignition switch ON (READY) | Below 1 V |
| B6-6 (IG2) - B6-10 (E1) | Power source | Ignition switch ON | 11 to 15.5 V |
| B6-10 (E1) - Body ground | Ground | Always | Below 1 Ω |
| B6-11 (E2) - Body ground | Ground | Always | Below 1 Ω |
| B6-12 (+B1) - B6-10 (E1) | Power source | Ignition switch ON | 11 to 15.5 V |
| B6-13 (+B2) - B6-10 (E1) | Power source | Ignition switch ON | 11 to 15.5 V |
Oscilloscope waveforms
Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.
Waveform 1
| Item | Content |
|---|---|
| Terminal | CH1: FRP - E1 |
| CH2: FRB+ - E1 | |
| CH3: FRG+ - E1 | |
| Equipment Setting | 10 V/DIV., 200 ms/DIV. |
| Condition | Ignition switch ON→Ignition switch ON (READY) |
Waveform 2
| Item | Content |
|---|---|
| Terminal | CH1: CA1H - E1 |
| CH2: CA1L - E1 | |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).
Waveform 3
| Item | Content |
|---|---|
| Terminal | CH1: HDCH - E1 |
| CH2: HDCL - E1 | |
| Equipment Setting | 1 V/DIV., 50 μs/DIV. |
| Condition | Ignition switch ON |
The waveform will vary depending on the content of the digital communication (digital signal).