Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM D

FC CONTROL  FC CONTROL SYSTEM  VEHICLE CONTROL HISTORY (RoB)  


VEHICLE CONTROL HISTORY (EV)


NOTICE:
·

If the electric motor power decreased or hydrogen filling was canceled due to factors other than vehicle malfunctions (DTCs were stored), such factors are recorded in the vehicle control history.

·

The vehicle control history stores freeze frame data for decreases of the motor power or cancelation of filling and the cumulative number of such events, in accordance with each of the following items.



HINT:
·

By referring to the freeze frame data recorded in the vehicle control history, it helps identify factors that caused the motor power to decrease or canceled filling.

·

Customer vehicle operations or vehicle drive conditions may cause the vehicle control history to be activated. Even if stored information was found in the vehicle control history, the vehicle is not in need of repairs unless the customer experienced power decreases or filling cancelation. Clear the vehicle control history and return the vehicle to the customer.



a.

Check Vehicle Control History

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / EV / Utility / Vehicle Control History (RoB).


v.

Check Vehicle Control History.

Powertrain > EV > Utility
Tester Display
Vehicle Control History (RoB)
50005 397 1055


b.

Clear Vehicle Control History

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / EV / Utility / Vehicle Control History (RoB).


v.

Press the "Clear key" at the bottom left of the screen.

HINT:

Performing this procedure will only clear the Vehicle Control History.





Vehicle control history items
FFD Group Code GTS Display Possible Cause Action to be Taken
12 X05A1 Target Driving Force Not Reached
If any one of the following conditions is met.
·

Insufficient driving force due to a decrease in EV supply battery assembly output before FC system power generation starts

·

Insufficient acceleration performance due to a decrease in responsiveness to an FC system power generation command

·

Insufficient driving force due to starting off on a hill when EV supply battery assembly output is limited

·

Power supply stops due to excessive permitted output during external power supply


Explain that the FC system or EV supply battery assembly temporarily has insufficient output, and that the condition will recover with further use.
12 X3000 Hydrogen Filling Abort
·

While filling at a hydrogen station, the hydrogen tank internal temperature or internal pressure increased, or the amount of filled hydrogen gas exceeded the specified tank capacity.

If any one of the following conditions is met, the vehicle control history will be activated.
-

"Hydrogen Tank 1 Temperature (Filtered Value)", "Hydrogen Tank 2 Temperature (Filtered Value)" or "Hydrogen Tank 3 Temperature (Filtered Value)" is higher than 85°C (185°F)

-

"Hydrogen Filling System High Pressure" is higher than 87.5 MPa

-

"Hydrogen Remaining" is over 100%

-

"Hydrogen Tank 1 Temperature (Filtered Value)", "Hydrogen Tank 2 Temperature (Filtered Value)" or "Hydrogen Tank 3 Temperature (Filtered Value)" is -45°C (-49°F) or less, and "Hydrogen Filling System High Pressure" is 5 MPa or less



Explain the customer that hydrogen filling may be canceled if the hydrogen tank internal pressure exceeds a specified level or a hydrogen tank internal temperature temporarily increases while the tank is refilled. If such happens, fill the tank again after a certain time interval, or at a different hydrogen station.
12 X3100 FC Output Limit
·

FC stack outlet coolant temperature increased (continuous uphill climb, etc. under high ambient temperature)

If the following condition is met, the vehicle control history will be activated. Refer to each data respectively.
-

"FC Stack Outlet Coolant Temperature (Filtered Value)" is around 85°C (185°F) (which varies depending on the FC stack conditions)



Explain the customer that the electric motor power needs to be temporarily limited in order to control the FC system properly.
·

Hydrogen system pressure decreased

If the following condition is met, the vehicle control history will be activated. Refer to each data respectively.
-

"Low-Range Hydrogen Pressure (Filtered Value)" is 110 kPa(abs) or less



Explain the customer that the electric motor power needs to be temporarily limited in order to control the FC system properly.
·

Vehicle continued traveling after the low fuel level warning light has come on

If the following condition is met, the vehicle control history will be activated. Refer to each data respectively.
-

"Medium-Range Hydrogen Pressure (Filtered Value)" is 1000 kPa(abs) or less



Explain the customer that the electric motor power needs to be temporarily limited in order to control the FC system properly.
·

Forced intermittent operation due to hydrogen leakage inspection

If the following condition is met, the vehicle control history will be activated. Refer to each data respectively.
-

"FC Output Power Limit Value (FC Intermittent Operation by Hydrogen Leak)" is 0 kW



Explain the customer that the electric motor power needs to be temporarily limited in order to control the FC system properly.
·

Air compressor was shut down

If the following condition is met, the vehicle control history will be activated. Refer to each data respectively.
-

"FC Output Power Limit Value (FC Air Compressor Shutdown)" is 0 kW



Explain the customer that the electric motor power needs to be temporarily limited in order to control the FC system properly.
·

FC stack cell voltage decreased

If the following condition is met, the vehicle control history will be activated. Refer to each data respectively.
-

Power restriction is actuated in accordance with the estimated FC stack condition based on the "FC Stack Cell Minimum Voltage" and "FC Stack Cell Average Minimum Voltage"



Explain the customer that the electric motor power needs to be temporarily limited in order to control the FC system properly.
·

FC air compressor component temperatures increased

If any one of the following conditions is met, the vehicle control history will be activated.
-

"FC Air Compressor Motor Temperature" is 130°C (266°F) or higher

-

"FC Air Compressor Inverter Temperature" is 115°C (239°F) or higher



Explain the customer that the electric motor power needs to be temporarily limited in order to control the FC system properly.
·

FC stack inlet air temperature or FC stack inlet air pressure increased

If any one of the following conditions is met, the vehicle control history will be activated.
-

"FC Inlet Air Temperature (Filtered Value)" is 100°C (212°F) or higher

-

"FC Inlet Air Pressure (Filtered Value)" is 250 kPa(abs) or higher



Explain the customer that the electric motor power needs to be temporarily limited in order to control the FC system properly.
·

High load requested when low temperature is determined in hydrogen system components


Explain that output may be temporarily limited in order to maintain appropriate control of the FC system. (Explain that the limitation is temporary until warm up is complete)
·

High load requested during a hydrogen system component (fuel injector assembly, exhaust drainage valve) malfunction


A hydrogen system component DTC is output, so perform troubleshooting.
·

High load requested during quick warmup


Explain that output may be temporarily limited in order to maintain appropriate control of the FC system. (Explain that the limitation is temporary until warmup is complete)
·

High load requested when hydrogen temperature inside the hydrogen tank assembly is extremely low


Explain that output may be temporarily limited in order to maintain appropriate control of the FC system.
12 X3101 FC System Start/Stop Failure
·

High voltage system/FC system start/stop process exceeds the specified time


There is an FC power generation malfunction, so perform troubleshooting for DTC P1DEF00.
12 X3102 FC System Start Up at Very Low Temperature
·

FC system was unable to start at an ambient temperature of below 0°C, due to frozen components.


Explain the customer that activation of the FC system is limited due to frozen components if an ambient temperature is below 0°C when the FC system is started. *2
1.

Leave vehicle to defrost

Leave the vehicle overnight at a location with an ambient temperature of 10°C (50°F) or more.


2.

Check that vehicle is defrosted

Using the GTS, check that "FC Stack Coolant Temperature (FC Stack Outlet)" is 5°C (41°F) or more.

HINT:

If the temperature specified above is not reached after leaving the vehicle overnight, be sure to check that "FC Stack Coolant Temperature (FC Stack Outlet)" is 1°C (34°F) or more.



3.

Start the vehicle

Enter the READY ON state and move to a location where water can be drained.


4.

Perform drainage

Turn the ignition switch to ON (READY) and then press the FC water release switch. Check that "FCV System Purge in Progress Purge will Stop Automatically" is displayed on the meter.


5.

Perform driving test

To reset the FC stack internal freezing history, fully warm up the vehicle and then drive for approximately 10 minutes.



·

Extended time delay after performing READY ON operation (turn the ignition switch to ON while stepping on the brake pedal) until the READY light changes from blinking to illuminated when at ambient temperature of below 0°C, due to frozen components.


Explain to the customer that it may take additional time for the READY light to change from blinking to illuminated after performing the READY ON operation (turn the ignition switch to ON while stepping on the brake pedal) when the ambient temperature is below 0°C, due to the time needed to thaw frozen components.
12 X3103 FC System Lack of Scavenging
·

Scavenging process terminated abnormally


If X3102 (start below freezing point) is output, explain that FC system starting is limited due to frozen components when starting below the freezing point. If only X3103 is output, this code may remain due to a system malfunction or an operation by the customer.
12 X3104 Gap in FC System Power Input/Output
If any one of the following conditions is met.
·

The EV supply battery assembly level is low or is fully charged

·

EV supply battery assembly output is high or charge amount is large

·

Charging is suspended after the ignition switch is turned off


-
12 X3110 Hydrogen Empty Low Level*1
·

Vehicle continued traveling until the FC system stopped even after the low fuel level warning light has come on

If any one of the following conditions is met, the vehicle control history will be activated.
-

"Hydrogen Empty Low Level" is ON

-

"Smoothed Value of Medium-range Hydrogen Pressure" is 1000 kPa(abs) or less



Explain the customer that the FC system may halt if the hydrogen tank internal pressure has decreased to the minimum pressure level (ran out of fuel).
12 X3240 Fuel Lid Interlock Activate
·

When the EV control ECU recognizes that the fuel lid is open and an attempt is made to turn the ignition switch to ON (READY), the ignition switch cannot be turned to ON (READY) (except in the following situation)


Explain that an attempt was made to turn the ignition switch to ON (READY) with the fuel lid open.
·

When the EV control ECU recognizes that the fuel lid is open, the ignition switch was to turned to ON (READY) using a forced release operation (5 start operations)


A history is stored when hydrogen filling was conducted and the pressure inside the hydrogen tank assembly rose when in any of the following situations.
·

Ignition switch ON (READY)

·

During pre-air conditioning

·

When using DC external power supply

·

When using AC 100 V external power supply

·

FC system freeze prevention control in operation

·

During service mode such as forced operation


Explain that hydrogen filling was performed during the FC system start process, operation and shutdown process.
- XF01B ECU Security Key Not Registered ECU security key has not been updated (Click here)

*1: FC system stopped (Mode enters EV drive mode, and travel distance will be limited)

*2: In order to identify the vehicle situation, it is helpful to save the data of "FC Output Limit" of the vehicle control history, and interview the customer about the time and distance travelled when they used the vehicle the last time, as well as the gradient of a parking area.

As for parking conditions, an indoor, not very cold and level area is recommended. (It is preferable that the vehicle is parked in a space where an ambient temperature remains above 10 °C (50 °F) overnight)


Vehicle Control History Freeze Frame Data (EV)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EV / Utility / Vehicle Control History (RoB).


e.

Select a vehicle control history item to access the applicable freeze frame data.


f.

Check the freeze frame Data recorded with the Vehicle Control History.

HINT:

Refer to the Data List for item descriptions.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>DATA LIST / ACTIVE TEST


Vehicle Control History Freeze Frame Data
Tester Display
Vehicle Speed
Atmospheric Pressure Sensor Voltage
Atmospheric Pressure
Atmospheric Pressure (Filtered Value)
Intake Air Temperature Sensor Voltage
Intake Air Temperature (Filtered Value)
Mass Air Flow Sensor Frequency
Target Mass Air Flow
Mass Air Flow (Filtered Value)
Estimate Gradient of Road Surface (Right and Left)
Ready Lighting Request (Normal Start)
Freeze Start Rejection
Accelerator Position
Total Voltage
Internal Voltage
Input Power
Shift Position
Fuel Lid Interlock Switch
Smoothed Value of BATT Voltage
Total Distance Traveled
Total Distance Traveled - Unit
IG2 Signal Status
Ready Signal
HV/EV Activate Condition
Radiator Rotary Valve Position
Target Radiator Rotary Valve Position
Tank Shut Valve 1 Status
Tank Shut Valve 2 Status
Tank Shut Valve 3 Status
Hydrogen Pump Speed
Target Hydrogen Pump Speed
FC Coolant Pump Speed
Target FC Coolant Pump Speed
FC Air Compressor Motor Speed
FC Air Compressor Motor Speed (Measured Value)
Target FC Air Compressor Motor Speed
Starting Status (An Side)
Stopping Status (An Side)
Starting Status (Ca Side)
Stopping Status (Ca Side)
Restart Execute Time
Emergency Shutdown Signal (FC)
FC Emergency Shutdown Signal
FC Start Request
FC Stop Request
Master Warning Lighting Request (FC)
FC Work Mode
FC System Status
FC Power Generation Status
Target FC Current (Filtered Value)
FC Current
FC Current (Filtered Value)
Maximum Available FC Current
FC Current Limit Value (Temperature High)
FC Current Limit Value (Hydrogen Stoichiometric Ratio)
FC Current Limit Value (Auxiliary Battery Driving)
FC Current Limit Value (Cell Monitor)
FC Voltage (Filtered Value)
FC Output Power Limit Value (FC Air Compressor Shutdown)
FC Output Power Limit Value (Hydrogen Gas Level Low)
FC Output Power Limit Value (FC Intermittent Operation by Hydrogen Leak)
FC Intermittent Operation
Target FC Temperature
Target FC Inlet Air Pressure
FC Inlet Air Pressure (Filtered Value)
FC Inlet Air Temperature (Filtered Value)
FC Coolant Pump Initial Request
FC Coolant Pump Main Power Supply Status
FC Coolant Pump Output Status
FC Coolant Pump Load Status
FC Coolant Pump Over Temperature Status
FC Coolant Pump STB Control Signal
FC Coolant Pump Inverter STB Status
FC Coolant Pump LIN Communication Control
FC Coolant Pump Isolation Fault Detection Control
Lost Communication with FC Coolant Pump
FC Coolant Pump CPU Abnormal
FC Coolant Pump Start Fail
FC Coolant Pump Consumption Power
FC Converter Status
FC Converter Shutdown Request
FC Converter Shutdown Status
FC Converter Shutdown Signal
FC Air Compressor Gate Shutdown Request
FC Air Compressor Shutdown Status
FC Air Compressor Consumption Power
FC Air Compressor Temperature just after IG ON
FC Air Compressor Maximum Temperature
FC Air Compressor Motor Operation Status
FC Air Compressor Motor Control Mode
V Phase FC Air Compressor Motor Current
W Phase FC Air Compressor Motor Current
FC Air Compressor Motor Carrier Frequency
FC Air Compressor Motor Temperature
FC Air Compressor Motor Temperature (Filtered Value)
FC Air Compressor Motor Torque Estimate Value
FC Stack Cell Average Minimum Voltage
FC Stack Cell Minimum Voltage
Estimate FC Stack Cell Minimum Voltage 1
Estimate FC Stack Cell Minimum Voltage 2
FC Stack Cell Average Minimum Voltage ch
FC Stack Cell Minimum Voltage ch
FC Stack Outlet Coolant Temperature Sensor Voltage
FC Stack Outlet Coolant Temperature (Filtered Value)
FC Stack Impedance
Maximum Impedance ch
Maximum Impedance Norm
Impedance Update Counter
FC Precharge Relay Request
FC Negative Relay Request
FC Positive Relay Request
Hydrogen Filling (FC)
Hydrogen Filling Control Module Power Supply Relay Drive Signal
Target Air Pressure Regulating Valve Position
Air Pressure Regulating Valve Position
Target Air Shunt Valve Position
Air Shunt Valve Position
Target Air Sealing Valve Position
Air Sealing Valve Position
Hydrogen Pump Initial Request
Hydrogen Pump Main Power Supply Status
Hydrogen Pump Output Status
Hydrogen Pump Load Status
Hydrogen Pump Inverter STB Status
Hydrogen Pump LIN Communication Control
Hydrogen Pump Isolation Fault Detection Control
Hydrogen Pump CPU Abnormal
Hydrogen Pump Start Fail
Hydrogen Pump Inverter Over Temperature Status
Hydrogen Pump Inverter STB Status
Hydrogen Pump Motor Temperature Sensor Voltage
Hydrogen Pump Motor Temperature (Filtered Value)
Hydrogen Injector Injection Number
Hydrogen Injector 1 Injection Period
Hydrogen Injector 2 Injection Period
Hydrogen Injector 3 Injection Period
Hydrogen Intake Pressure Sensor Voltage
Hydrogen Intake Pressure Sensor Value
Target Low-Range Hydrogen Pressure
High-Range Hydrogen Pressure (Filtered Value)
Medium-Range Hydrogen Pressure (Filtered Value)
Low-Range Hydrogen Pressure (Filtered Value)
Hydrogen Detector (Motor Room) Frequency
Motor Room Hydrogen Density
Hydrogen Detector 1 Frequency
Tank Area 1 Hydrogen Density
Hydrogen Detector 2 Frequency
Tank Area 2 Hydrogen Density
Hydrogen Gas Empty
Purge Amount Estimate Value
Hydrogen Gas Level
Exhaust Drainage Valve
Hydrogen Tank 1 Temperature at Hydrogen Filling
Hydrogen Tank 1 Temperature (Filtered Value)
Hydrogen Tank 1 Temperature Sensor Voltage
Hydrogen Tank 1 Temperature (1 sec before Hydrogen Filling Abort)
Hydrogen Tank 1 Temperature (2 sec before Hydrogen Filling Abort)
Hydrogen Tank 1 Temperature (3 sec before Hydrogen Filling Abort)
Hydrogen Tank 1 Temperature at Hydrogen Filling Abort
Hydrogen Tank 2 Temperature at Hydrogen Filling
Hydrogen Tank 2 Temperature (Filtered Value)
Hydrogen Tank 2 Temperature Sensor Voltage
Hydrogen Tank 2 Temperature (1 sec before Hydrogen Filling Abort)
Hydrogen Tank 2 Temperature (2 sec before Hydrogen Filling Abort)
Hydrogen Tank 2 Temperature (3 sec before Hydrogen Filling Abort)
Hydrogen Tank 2 Temperature at Hydrogen Filling Abort
Hydrogen Tank 3 Temperature at Hydrogen Filling
Hydrogen Tank 3 Temperature (Filtered Value)
Hydrogen Tank 3 Temperature Sensor Voltage
Hydrogen Tank 3 Temperature (1 sec before Hydrogen Filling Abort)
Hydrogen Tank 3 Temperature (2 sec before Hydrogen Filling Abort)
Hydrogen Tank 3 Temperature (3 sec before Hydrogen Filling Abort)
Hydrogen Tank 3 Temperature at Hydrogen Filling Abort
Hydrogen Intake Pressure (1 sec before Hydrogen Filling Abort)
Hydrogen Intake Pressure (2 sec before Hydrogen Filling Abort)
Hydrogen Intake Pressure (3 sec before Hydrogen Filling Abort)
Hydrogen Intake Pressure at Hydrogen Filling Abort
Hydrogen Intake Pressure at Hydrogen Filling
Hydrogen Tank SOC (1 sec before Hydrogen Filling Abort)
Hydrogen Tank SOC (2 sec before Hydrogen Filling Abort)
Hydrogen Tank SOC (3 sec before Hydrogen Filling Abort)
Hydrogen Tank SOC at Hydrogen Filling Abort
Main Radiator Fan Voltage
Main Radiator Fan Control Duty
Radiator Outlet Coolant Temperature Sensor Voltage
Radiator Outlet Coolant Temperature (Filtered Value)
FCV System Status
FCDC Permission Current
FCDC Input Voltage
FCDC Output Voltage
Master Warning Lighting Request (FCDC)
FCDC Fail Signal
Fail Safe Request
Fail Safe Status (FCDC CAN Communication Status)
Communication Error from Cell Monitor to FCDC
Cell Monitor AD Abnormal
Cell Monitor ROM Abnormal
Cell Monitor RAM Abnormal
Cell Monitor Abnormal 1
Cell Monitor Abnormal 2
Cell Monitor Abnormal 1 (First Out)
Cell Monitor Abnormal 2 (First Out)
Cell Monitor Power Supply Voltage Low
Cell Monitor Power Supply Voltage
Ion Exchanger Maintenance Distance
Conductivity Reduction Complete



VEHICLE CONTROL HISTORY (FCDC)


HINT:

Customer vehicle operations or vehicle drive conditions may cause the vehicle control history to be activated. Even if stored information was found in the vehicle control history, the vehicle is not in need of repairs unless the customer experienced power decreases or filling cancelation. Clear the vehicle control history and return the vehicle to the customer.


a.

Check Vehicle Control History

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / FCDC / Utility / Vehicle Control History (RoB).


v.

Check Vehicle Control History.

Powertrain > FCDC > Utility
Tester Display
Vehicle Control History (RoB)
50005 493 1055


b.

Clear Vehicle Control History

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / FCDC / Utility / Vehicle Control History (RoB).


v.

Press the "Clear key" at the bottom left of the screen.

HINT:

Performing this procedure will only clear the Vehicle Control History.





Vehicle control history items
FFD Group Code GTS Display Possible Cause Action to be Taken
01 X05A2 Target FC Current Not Reached
·

The FC boost control ECU outputs an FC current based on the FC current command value from the EV control ECU, but the function is not fulfilled for some reason

The history will remain when in any of the following conditions. Refer to the freeze frame data of each item.
-

The FC current upper limit (FC boost control ECU restriction) is 480 A or less continuously for 3 seconds

-

The FC current upper limit (FC boost control ECU restriction) is 240 A or less continuously for 1 second

-

The FC current value is 60 A less than the FC boost control ECU current command value continuously for 3 seconds

-

The FC current value is 120 A less than the FC boost control ECU current command value continuously for 1 second



Explain that the upper limit of 600 A (when the FC boost control ECU is operating normally) cannot be output or that the FC current value is insufficient for the FC boost control ECU current command value for some reason, when output is limited due to a high temperature or there are limitations due to a malfunction occurring.
- XF01B ECU Security Key Not Registered ECU security key has not been updated (Click here)

Vehicle Control History Freeze Frame Data (FCDC)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / FCDC / Utility / Vehicle Control History.


e.

Select a vehicle control history item to access the applicable freeze frame data.


f.

Check the freeze frame Data recorded with the Vehicle Control History.

HINT:

Refer to the Data List for item descriptions.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>DATA LIST / ACTIVE TEST


Vehicle Control History Freeze Frame Data
Tester Display
Shutdown Request (Hybrid/EV)
Inverter Shutdown Status
Fail Safe Status
FC Voltage (Filtered Value)
FC Converter Output Voltage (Filtered Value)
FC Voltage
FC Converter Output Voltage
Power Supply Monitor Voltage (+B)
Power Supply Monitor Voltage (-5V)
FC Current
FC Current Upper Limit
Target FC Current (Hybrid/EV)
FC Current (Filtered Value)
Phase U Duty
Phase U Temperature 1
Phase U Temperature 2
Phase U Current
Phase U Current (Offset Value)
Phase V Duty
Phase V Temperature 1
Phase V Temperature 2
Phase V Current
Phase V Current (Offset Value)
Phase W Duty
Phase W Temperature 1
Phase W Temperature 2
Phase W Current
Phase W Current (Offset Value)
Phase X Duty
Phase X Temperature 1
Phase X Temperature 2
Phase X Current
Phase X Current (Offset Value)



VEHICLE CONTROL HISTORY (SRS AIRBAG)


HINT:

A part of the control history can be confirmed using the vehicle control history.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>VEHICLE CONTROL HISTORY