Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1D0618  FC Converter Phase U Current Circuit Current Below Threshold  P1D0718  FC Converter Phase V Current Circuit Current Below Threshold  P1D0818  FC Converter Phase W Current Circuit Current Below Threshold  P1D0918  FC Converter Phase X Current Circuit Current Below Threshold  


DESCRIPTION

The FC boost control ECU is located inside the FC converter assembly. It monitors the electric current of the circuits using the reactor current sensor inside the FC converter assembly and detects a short in the diode circuits.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D0618 FC Converter Phase U Current Circuit Current Below Threshold A short in the phase U output diode circuit is detected.
(The phase U reactor current output from the negative terminal is estimated to be caused by a reverse charging of the FC stack.)
(1 trip detection logic)
FC converter assembly Master Warning: Comes on FCDC B
P1D0718 FC Converter Phase V Current Circuit Current Below Threshold A short in the phase V output diode circuit is detected.
(The phase V reactor current output from the negative terminal is estimated to be caused by a reverse charging of the FC stack.)
(1 trip detection logic)
FC converter assembly Master Warning: Comes on FCDC B
P1D0818 FC Converter Phase W Current Circuit Current Below Threshold A short in the phase W output diode circuit is detected.
(The phase W reactor current output from the negative terminal is estimated to be caused by a reverse charging of the FC stack.)
(1 trip detection logic)
FC converter assembly Master Warning: Comes on FCDC B
P1D0918 FC Converter Phase X Current Circuit Current Below Threshold A short in the phase X output diode circuit is detected.
(The phase X reactor current output from the negative terminal is estimated to be caused by a reverse charging of the FC stack.)
(1 trip detection logic)
FC converter assembly Master Warning: Comes on FCDC B

Related Data List
DTC No. Data List
P1D0618 Phase U Current
P1D0718 Phase V Current
P1D0818 Phase W Current
P1D0918 Phase X Current

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON.

2.

Enter the following menus: Powertrain / EV / Data List / FC Work Mode, FC Intermittent Operation.

3.

Put the state in park (P), turn the ignition switch to ON (READY) and wait until the FC system is activated (Waiting for at least 2 minutes is required after turning the ignition switch to ON (READY)).

FC system is activated: Data List shows that "FC Work Mode" is "Working" and "FC Intermittent Operation" is "OFF".


4.

Wait at least 15 seconds with the FC system activated.

5.

Drive the vehicle forward with the shift state in drive (D) for 5 m (16 ft.) or more.

6.

Drive the vehicle backward with the shift state in reverse (R) for 5 m (16 ft.) or more.



PROCEDURE

1.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
Only P1D0618, P1D0718, P1D0818 or P1D0918 is output A
P1D0618, P1D0718, P1D0818 or P1D0918 is output and DTCs other than the DTCs in the table below are output B
P1D0618, P1D0718, P1D0818 or P1D0918 is output and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1D3011 Phase U Reactor Current Sensor Circuit Short to Ground
P1D3015 Phase U Reactor Current Sensor Circuit Short to Battery or Open
P1D301C Phase U Reactor Current Sensor Circuit Voltage Out of Range
P1D3028 Phase U Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3511 Phase V Reactor Current Sensor Circuit Short to Ground
P1D3515 Phase V Reactor Current Sensor Circuit Short to Battery or Open
P1D351C Phase V Reactor Current Sensor Circuit Voltage Out of Range
P1D3528 Phase V Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3A11 Phase W Reactor Current Sensor Circuit Short to Ground
P1D3A15 Phase W Reactor Current Sensor Circuit Short to Battery or Open
P1D3A1C Phase W Reactor Current Sensor Circuit Voltage Out of Range
P1D3A28 Phase W Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D4011 Phase X Reactor Current Sensor Circuit Short to Ground
P1D4015 Phase X Reactor Current Sensor Circuit Short to Battery or Open
P1D401C Phase X Reactor Current Sensor Circuit Voltage Out of Range
P1D4028 Phase X Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure


HINT:

DTC P1D0618, P1D0718, P1D0818 or P1D0918 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (EV)

B

2.CHECK DTC OUTPUT (EV)

C

GO TO DTC CHART

2.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
System malfunction P1A8F00 Drive Motor "A" Inverter Overvoltage (System Performance)
P1C8149 High Voltage Power Resource Circuit Consumption Circuit Short


HINT:

DTC P1D0618, P1D0718, P1D0818 or P1D0918 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

3.CLEAR DTC

B

3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > FCDC > Clear DTCs
50002 493
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

4.CHECK DTC OUTPUT (FCDC)
4.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
DTCs are not output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1D3011 Phase U Reactor Current Sensor Circuit Short to Ground
P1D3015 Phase U Reactor Current Sensor Circuit Short to Battery or Open
P1D301C Phase U Reactor Current Sensor Circuit Voltage Out of Range
P1D3028 Phase U Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3511 Phase V Reactor Current Sensor Circuit Short to Ground
P1D3515 Phase V Reactor Current Sensor Circuit Short to Battery or Open
P1D351C Phase V Reactor Current Sensor Circuit Voltage Out of Range
P1D3528 Phase V Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3A11 Phase W Reactor Current Sensor Circuit Short to Ground
P1D3A15 Phase W Reactor Current Sensor Circuit Short to Battery or Open
P1D3A1C Phase W Reactor Current Sensor Circuit Voltage Out of Range
P1D3A28 Phase W Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D4011 Phase X Reactor Current Sensor Circuit Short to Ground
P1D4015 Phase X Reactor Current Sensor Circuit Short to Battery or Open
P1D401C Phase X Reactor Current Sensor Circuit Voltage Out of Range
P1D4028 Phase X Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure


HINT:

DTC P1D0618, P1D0718, P1D0818 or P1D0918 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

5.SIMULATION TEST

B

GO TO DTC CHART

5.SIMULATION TEST

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


b.

Drive the vehicle in a city area under the vehicle and driving conditions based on the recorded freeze frame data for approximately 10 minutes.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
DTCs are not output A
Only P1D0618, P1D0718, P1D0818 or P1D0918 is output B
P1D0618, P1D0718, P1D0818 or P1D0918 is output and DTCs other than the DTCs in the table below are output C
P1D0618, P1D0718, P1D0818 or P1D0918 is output and any DTCs in the table below are output D

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1D3011 Phase U Reactor Current Sensor Circuit Short to Ground
P1D3015 Phase U Reactor Current Sensor Circuit Short to Battery or Open
P1D301C Phase U Reactor Current Sensor Circuit Voltage Out of Range
P1D3028 Phase U Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3511 Phase V Reactor Current Sensor Circuit Short to Ground
P1D3515 Phase V Reactor Current Sensor Circuit Short to Battery or Open
P1D351C Phase V Reactor Current Sensor Circuit Voltage Out of Range
P1D3528 Phase V Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D3A11 Phase W Reactor Current Sensor Circuit Short to Ground
P1D3A15 Phase W Reactor Current Sensor Circuit Short to Battery or Open
P1D3A1C Phase W Reactor Current Sensor Circuit Voltage Out of Range
P1D3A28 Phase W Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure
P1D4011 Phase X Reactor Current Sensor Circuit Short to Ground
P1D4015 Phase X Reactor Current Sensor Circuit Short to Battery or Open
P1D401C Phase X Reactor Current Sensor Circuit Voltage Out of Range
P1D4028 Phase X Reactor Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure


HINT:

DTC P1D0618, P1D0718, P1D0818 or P1D0918 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

B

REPLACE FC CONVERTER ASSEMBLY

C

REPLACE FC CONVERTER ASSEMBLY

D

GO TO DTC CHART