Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0455055 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B14B2  Lost Communication with Front Panel LIN  


DESCRIPTION

The air conditioning control assembly communicates with the air conditioning amplifier assembly via LIN communication.

If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate even if the air conditioning control assembly is operated.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B14B2 Lost Communication with Front Panel LIN Lost communication with air conditioning control assembly
Diagnosis condition:

Ignition switch ON


Malfunction status:

Lost communication with air conditioning control assembly


Detection time:

Continuously for 10 seconds or more


·

Harness or connector

·

Air conditioning control assembly

·

Air conditioning amplifier assembly


Memorized Air Conditioner A

WIRING DIAGRAM

w/ Navigation System:
E457280E03
5.615,0.479 6.073,0.677 0.458,0.198 10 false +B 5.625,1.542 6.083,1.74 0.458,0.198 10 false LIN1 5.625,2.073 6.083,2.271 0.458,0.198 10 false GND 5.365,2.427 5.823,2.625 0.458,0.198 10 false D81 6.5,1.667 6.792,1.865 0.292,0.198 10 false AD 5.385,2.604 6.958,3.115 1.573,0.51 10 false Air Conditioning Amplifier Assembly 5.385,0.375 5.844,0.573 0.458,0.198 10 false 5 5.396,1.531 5.854,1.729 0.458,0.198 10 false 7 5.292,1.927 5.75,2.125 0.458,0.198 10 false 17 1.76,1.146 2.219,1.344 0.458,0.198 10 false 4 1.75,1.531 2.208,1.729 0.458,0.198 10 false 3 1.76,1.927 2.219,2.125 0.458,0.198 10 false 8 1.385,1.146 1.844,1.344 0.458,0.198 10 false IG+ 1.344,1.531 1.802,1.729 0.458,0.198 10 false LIN1 1.531,1.927 1.99,2.125 0.458,0.198 10 false E 0.49,1.677 0.948,1.875 0.458,0.198 10 false CPU 0.229,2.438 0.688,2.635 0.458,0.198 10 false D90 0.24,2.615 1.719,2.979 1.479,0.365 10 false Air Conditioning Control Assembly 0.781,3.458 2.823,3.656 2.042,0.198 10 false : LIN Communication Line 2.021,1.427 3.031,1.635 1.01,0.208 10 false IG1 P NO.4 4.51,1.01 5.521,1.219 1.01,0.208 10 false A/C NO.1 3.135,0.844 4.698,1.063 1.563,0.219 10 false from A/C Relay 4.49,0.646 5.5,0.854 1.01,0.208 10 false A/C NO.2 2.938,0.49 4.479,0.677 1.542,0.188 10 false from A/C Relay 5.635,0.875 6.094,1.073 0.458,0.198 10 false IG+ 5.385,0.76 5.844,0.958 0.458,0.198 10 false 6 3.281,1.25 4.844,1.469 1.563,0.219 10 false from IG1 P NO.2 Relay

w/o Navigation System:
E457280E04
5.615,0.479 6.073,0.677 0.458,0.198 10 false +B 5.625,1.542 6.083,1.74 0.458,0.198 10 false LIN1 5.625,2.073 6.083,2.271 0.458,0.198 10 false GND 5.365,2.427 5.823,2.625 0.458,0.198 10 false D81 6.5,1.667 6.792,1.865 0.292,0.198 10 false AD 5.385,2.604 6.958,3.115 1.573,0.51 10 false Air Conditioning Amplifier Assembly 5.385,0.375 5.844,0.573 0.458,0.198 10 false 5 5.396,1.531 5.854,1.729 0.458,0.198 10 false 7 5.292,1.927 5.75,2.125 0.458,0.198 10 false 17 1.76,1.146 2.219,1.344 0.458,0.198 10 false 8 1.75,1.531 2.208,1.729 0.458,0.198 10 false 6 1.76,1.927 2.219,2.125 0.458,0.198 10 false 1 1.385,1.146 1.844,1.344 0.458,0.198 10 false IG+ 1.344,1.531 1.802,1.729 0.458,0.198 10 false LIN1 1.531,1.927 1.99,2.125 0.458,0.198 10 false E 0.49,1.677 0.948,1.875 0.458,0.198 10 false CPU 0.229,2.438 0.688,2.635 0.458,0.198 10 false D91 0.24,2.615 1.719,2.979 1.479,0.365 10 false Air Conditioning Control Assembly 0.781,3.458 2.823,3.656 2.042,0.198 10 false : LIN Communication Line 2.021,1.427 3.031,1.635 1.01,0.208 10 false IG1 P NO.4 4.51,1.01 5.521,1.219 1.01,0.208 10 false A/C NO.1 3.135,0.844 4.698,1.063 1.563,0.219 10 false from A/C Relay 4.49,0.646 5.5,0.854 1.01,0.208 10 false A/C NO.2 2.938,0.49 4.479,0.677 1.542,0.188 10 false from A/C Relay 5.635,0.875 6.094,1.073 0.458,0.198 10 false IG+ 5.385,0.76 5.844,0.958 0.458,0.198 10 false 6 3.281,1.25 4.844,1.469 1.563,0.219 10 false from IG1 P NO.2 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)

B

6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the D90 air conditioning control assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D90)Location & Routing

Click Connector(D90)Instrument Panel>Instrument Panel Wire>Air Conditioning Control Assembly

D90-8 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BATTERY)

Pre-procedure1

a.

Disconnect the D90 air conditioning control assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D90)Location & Routing

Click Connector(D90)Instrument Panel>Instrument Panel Wire>Air Conditioning Control Assembly

D90-4 (IG+) - Body ground Ignition switch ON 11 to 14 V
D90-4 (IG+) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the D90 air conditioning control assembly connector.


b.

Disconnect the D81 air conditioning amplifier assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D90,D81)Location & Routing

Click Connector(D90)Instrument Panel>Instrument Panel Wire>Air Conditioning Control Assembly

Click Connector(D81)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assembly

D90-3 (LIN1) - D81-7 (LIN1) Always Below 1 Ω
D90-3 (LIN1) or D81-7 (LIN1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

Pre-procedure1

a.
E407118C09
0.417,0.5 0.917,0.75 0.5,0.25 2.5,0.99 2.25,0.99 2.25,0.99 1.99,0.719 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 0.177,2.948 0.563,3.146 0.385,0.198 10 false GND 2.563,0.906 2.917,1.104 0.354,0.198 10 false LIN1 0.542,0.552 0.854,0.75 0.313,0.198 10 false D81
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Disconnect the D90 air conditioning control assembly connector.


Procedure1

a.

Using an oscilloscope, check the waveform.

Tester Connection Tool Setting Switch Condition

Click Location & Routing(D81)Location & Routing

Click Connector(D81)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assembly

D81-7 (LIN1) - Body ground 2 V/DIV., 20 ms/DIV. Ignition switch ON

OK:

The waveform displays properly.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the D91 air conditioning control assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D91)Location & Routing

Click Connector(D91)Instrument Panel>Instrument Panel Wire>Air Conditioning Control Assembly

D91-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BATTERY)

Pre-procedure1

a.

Disconnect the D91 air conditioning control assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D91)Location & Routing

Click Connector(D91)Instrument Panel>Instrument Panel Wire>Air Conditioning Control Assembly

D91-8 (IG+) - Body ground Ignition switch ON 11 to 14 V
D91-8 (IG+) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the D91 air conditioning control assembly connector.


b.

Disconnect the D81 air conditioning amplifier assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D91,D81)Location & Routing

Click Connector(D91)Instrument Panel>Instrument Panel Wire>Air Conditioning Control Assembly

Click Connector(D81)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assembly

D91-6 (LIN1) - D81-7 (LIN1) Always Below 1 Ω
D91-6 (LIN1) or D81-7 (LIN1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

Pre-procedure1

a.
E407118C09
0.417,0.5 0.917,0.75 0.5,0.25 2.5,0.99 2.25,0.99 2.25,0.99 1.99,0.719 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 0.177,2.948 0.563,3.146 0.385,0.198 10 false GND 2.563,0.906 2.917,1.104 0.354,0.198 10 false LIN1 0.542,0.552 0.854,0.75 0.313,0.198 10 false D81
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Disconnect the D91 air conditioning control assembly connector.


Procedure1

a.

Using an oscilloscope, check the waveform.

Tester Connection Tool Setting Switch Condition

Click Location & Routing(D81)Location & Routing

Click Connector(D81)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assembly

D81-7 (LIN1) - Body ground 2 V/DIV., 20 ms/DIV. Ignition switch ON

OK:

The waveform displays properly.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG