The cooler control switch assembly communicates with the air conditioning amplifier assembly via LIN communication.
If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate even if the cooler control switch assembly is operated.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| B14B3 | Lost Communication with Rear Panel LIN | Lost communication with cooler control switch assembly
Diagnosis condition:
Ignition switch ON Malfunction status:
Lost communication with cooler control switch assembly Detection time:
Continuously for 10 seconds or more |
·
Harness or connector ·
Cooler control switch assembly ·
Air conditioning amplifier assembly |
Memorized | Air Conditioner | A |
Inspect the fuses for circuits related to this system before performing the following procedure.
Pre-procedure1
Disconnect the l1 cooler control switch assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(I1)Location & Routingewd_type=routing;type=c;code=I1 Click Connector(I1)Seat>Rear Console Box Wire>Cooler Control Switch Assemblyewd_type=component;type=c;code=I1;pinno=16 |
||
| I1-16 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the l1 cooler control switch assembly connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(I1)Location & Routingewd_type=routing;type=c;code=I1 Click Connector(I1)Seat>Rear Console Box Wire>Cooler Control Switch Assemblyewd_type=component;type=c;code=I1;pinno=1,9,10 |
||
| I1-1 - Body ground | Ignition switch ON | 11 to 14 V |
| I1-1 - Body ground | Ignition switch off | Below 1 V |
| I1-9 - Body ground | Ignition switch ON | 11 to 14 V |
| I1-9 - Body ground | Ignition switch off | Below 1 V |
| I1-10 - Body ground | Ignition switch ON | 11 to 14 V |
| I1-10 - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I1 rear console box wire connector.
Disconnect the D79 air conditioning amplifier assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(I1,D79)Location & Routingewd_type=routing;type=c,c;code=I1,D79 Click Connector(I1)Seat>Rear Console Box Wire>Cooler Control Switch Assemblyewd_type=component;type=c;code=I1;pinno=13 Click Connector(D79)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=D79;pinno=20 |
||
| I1-13 - D79-20 (RLIN) | Always | Below 1 Ω |
| I1-13 or D79-20 (RLIN) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I1 rear console box wire connector.
Procedure1
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Using an oscilloscope, check the waveform.
| Tester Connection | Tool Setting | Switch Condition |
|---|---|---|
|
Click Location & Routing(D79)Location & Routingewd_type=routing;type=c;code=D79 Click Connector(D79)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=D79;pinno=20 |
||
| D79-20 (RLIN) - Body ground | 2 V/DIV., 20 ms/DIV. | Ignition switch ON |
The waveform displays properly.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG