Home › Vehicle Interior › DOOR LOCK › LUGGAGE COMPARTMENT DOOR LOCK › from 2021.08
RM37H0E _58 Vehicle Interior _095313 DOOR LOCK _0453006 LUGGAGE COMPARTMENT DOOR LOCK G

DOOR LOCK  LUGGAGE COMPARTMENT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 64610 1.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY (w/o Easy Closer)

a.

Check the close operation of the luggage door closer assembly.

i.

Set the luggage door closer assembly to the full latch position.


ii.
E239945C08
1.583,3.188 1.917,3.375 0.333,0.188 1.604,1.313 1.719,1.5 1.719,1.5 1.917,1.5 false 1.51,3.938 1.042,4.271 true 1.76,3.99 1.76,4.281 true 2,3.927 2.458,4.229 true 1.979,1.427 2.198,1.646 0.219,0.219 10 false *1 0.542,0.26 0.792,0.479 0.25,0.219 10 false *a 0.542,1.979 0.792,2.198 0.25,0.219 10 false *b 0.865,3.219 1.115,3.438 0.25,0.219 10 false *c 0.938,4.292 1.188,4.51 0.25,0.219 10 false D+ 1.75,4.344 2.104,4.51 0.354,0.167 10 false E 2.49,4.26 2.844,4.427 0.354,0.167 10 false B 1.667,3.219 1.979,3.417 0.313,0.198 10 false K1
*1 Latch
*a Full latch
*b Open latch
*c Component without harness connected
(Luggage Compartmen Door Lock Assembly)


Apply auxiliary battery voltage to the luggage door closer motor and check the operation of the luggage door closer motor.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(K1)Location & Routing

Click Connector(K1)Body>No. 1 Back Door Wire>Luggage Compartment Door Lock Assembly

K1-1(B) - K1-2(E) K1-1(B) - Auxiliary battery positive (+)
K1-2(E) - Auxiliary battery negative (-)
Moves to Open latch position



iii.

Check the resistance of the luggage compartment door courtesy switch.

1.

Measure the resistance according to the value(s) in the table below.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(K1)Location & Routing

Click Connector(K1)Body>No. 1 Back Door Wire>Luggage Compartment Door Lock Assembly

K1-3(D+) - K1-2(E) Open latch Below 1 Ω
K1-3(D+) - K1-2(E) Full latch 10 kΩ or higher





Hide 64650 2.INSPECT LUGGAGE DOOR CLOSER ASSEMBLY (w/ Easy Closer)

a.

Check the close operation of the luggage door closer assembly.

i.
B590832C02
1.552,3.208 1.969,3.458 0.417,0.25 2.01,2.438 2.688,2.49 true 2.042,2.646 2.656,2.792 true 1.979,2.885 2.615,3.052 true 2.115,3.792 2.51,3.792 true 2.115,3.969 2.354,4.177 2.354,4.177 2.5,4.177 true 0.5,3.115 0.813,3.271 0.313,0.156 10 false *a 2.76,2.427 3.073,2.583 0.313,0.156 10 false *b 2.75,2.75 3.063,2.906 0.313,0.156 10 false *c 2.698,3.021 3.01,3.177 0.313,0.156 10 false *d 2.583,3.719 2.896,3.875 0.313,0.156 10 false M- 2.563,4.104 2.896,4.281 0.333,0.177 10 false M+ 1.688,3.25 2.104,3.417 0.417,0.167 10 false K2
*a Component without harness connected
(Luggage Door Closer Assembly)
*b Full latch
*c Half-latch
*d Open latch


Set the luggage door closer assembly to the half-latch position.


ii.

Apply auxiliary battery voltage to the luggage door closer motor and check the operation of the luggage door closer motor.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(K2)Location & Routing

Click Connector(K2)Body>No. 1 Back Door Wire>Luggage Door Closer Assembly

K2-8(M+) - K2-1(M-) K2-8(M+) - Auxiliary battery positive (+)
K2-1(M-) - Auxiliary battery negative (-)
Moves to full latch position


HINT:

If the result is not as specified, replace the luggage door closer assembly.




b.

Check the open operation of the luggage door closer assembly.

i.

Set the luggage door closer assembly to the full-latch position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K2)Location & Routing

Click Connector(K2)Body>No. 1 Back Door Wire>Luggage Door Closer Assembly

K2-8(M+) - K2-1(M-) K2-1(M-) - Auxiliary battery positive (+)
K2-8(M+) - Auxiliary battery negative (-)
Moves to open latch position


HINT:

If the result is not as specified, replace the luggage compartment door lock assembly.