TELEMATICS SYSTEM OUTLINE
The telematics system is a telematics service that links the vehicle and TOYOTA Connect network (provides information from the TOYOTA Connect center or content providers).
The user needs to follow the instructions on the multi-display assembly screen to start using the telematics system service after applying for the service at a dealership.
FUNCTION OF MAIN COMPONENTS
| Component | Function | |||
|---|---|---|---|---|
| Map Light Assembly
·
Emergency Call Switch |
When the emergency call switch is pressed, a switch signal is sent to the telematics transceiver. (When a manual maintenance check or manual emergency call is performed.) | |||
| LED Indicator Light | Green | ·
Turns on for 5 seconds after the ignition switch is turned to ON. ·
Turns on when the system is under a service contract and the telematics transceiver is within the service area. ·
Blinks during an emergency call. ·
Blinks during a manual maintenance check. ·
Turns off when the system is malfunctioning or the telematics transceiver is not within the service area. |
||
| Red | ·
Turns on for 5 seconds after the ignition switch is turned to ON. ·
Turns on when the telematics transceiver is not within the service area. ·
Blinks when an emergency call is made while the system is still malfunctioning. ·
Turns off when the system is operating normally. ·
Blinks in diagnostic mode to indicate a DTC. ·
Blinks in diagnostic mode to indicate a specific vehicle history. |
|||
| Telephone Microphone Assembly | ·
When the operator service is used: Sends the microphone voice signal to the radio receiver assembly. ·
When an emergency call is made: Sends the microphone voice signal to the telematics transceiver. |
|||
| Telephone Antenna Assembly | Telephone Antenna (Main) | Sends and receives the data and voice signals used for the TOYOTA Connect through a communication network. (Connect as main) | ||
| GPS Antenna | Receives signals from GPS satellites and transmits these signals to the navigation ECU assembly. | |||
| Navigation Antenna Assembly | Telephone Antenna (Sub) | Receives signals from the service center. (Connect as sub) | ||
| Telematics Transceiver | ·
Uses the telephone antenna assembly to send and receive the data and voice signals used for the TOYOTA Connect through a communication network. -
When the operator service is used: Sends the received voice signal to the radio receiver assembly. -
When the operator service is used: Sends the sent voice signal from the radio receiver assembly to the telephone antenna assembly. -
When an emergency call is made: Sends the received voice signal to the vehicle speakers. -
When an emergency call is made: Receives the sent voice signal from the telephone microphone assembly. -
When an emergency call is made: Sends a mute signal to the stereo component amplifier assembly. (Mute function becomes active during the call.) -
When an emergency call is made: Sends vehicle location information to the TOYOTA Connect center. -
When a warning occurs, the telematics transceiver receives a warning ON signal from the combination meter assembly via CAN communication and sends it to the TOYOTA Connect center. -
When the theft deterrent system is activated, the telematics transceiver sends information that the security horn has sounded to the TOYOTA Connect center. |
|||
| Mobilephone battery (Back-up Battery) | ·
When an automatic emergency call is performed, the mobilephone battery provides power to the telematics transceiver. ·
When a manual emergency call is made, the mobilephone battery is not used as the power source. ·
The mobilephone battery conducts a self-diagnosis every time the ignition switch is turned to ON, and after an automatic emergency call or manual emergency call is made, and the result is sent to the telematics transceiver. |
|||
| Main Body ECU (Multiplex Network Body ECU) | Sends a security horn sounding signal to the telematics transceiver when the theft deterrent system is activated. | |||
| Radio Receiver Assembly | Sends and receives the data used for the TOYOTA Connect to and from the telematics transceiver using a telematics data signal. -
When the operator service is used: Sends the sent voice signal from the telephone microphone assembly to the telematics transceiver. -
When the operator service is used: Sends the received voice signal from the telematics transceiver to the stereo component amplifier assembly using a MOST signal. |
|||
| Navigation ECU Assembly | Sends and receives the data used for the TOYOTA Connect to and from the telematics transceiver using a telematics data signal. -
Sends vehicle location information to the telematics transceiver. |
|||
| Stereo Component Amplifier Assembly | Receives the received voice signal sent from the radio receiver assembly as a sound signal and outputs it as sound from the front No. 1 speaker assembly RH and No. 3 speaker assembly RH via the telematics transceiver. (When the operator service is used.) | |||
| Airbag ECU Assembly | Sends an activation signal to the telematics transceiver when airbags deploy. (An automatic emergency call is made.) | |||
| Combination Meter Assembly | Sends a warning signal to the telematics transceiver via CAN communication when a warning occurs. | |||
DEVICE USED FOR TELEMATICS SYSTEM COMMUNICATION
The telematics transceiver is used for data communication or emergency call service telephone calls and operator service telephone calls.
The hands-free function does not use the telematics transceiver. A user's "Bluetooth" compatible cellular phone needs to be used.
Perform the following if the device used for telematics system communication is replaced.
If the navigation ECU assembly or the telematics transceiver is replaced on vehicles that do not have a contract for the TOYOTA Connect, perform vehicle contract setting.
If the navigation ECU assembly or the telematics transceiver is replaced on vehicles that have a contract for the TOYOTA Connect, perform the vehicle contract setting and the procedure to resume the TOYOTA Connect to start the emergency call service.
TELEMATICS TRANSCEIVER OUTLINE
On this model, the telematics transceiver functions as the TOYOTA Connect device.
The telematics transceiver has a serial number (IMEI) which can be used to determine the individual device when servicing.
TOYOTA Connect SUPPORT CENTER OUTLINE
The TOYOTA Connect support center provides members with opportunities to ask questions and information necessary for troubleshooting.
| Main Service | Outline |
|---|---|
| Answering questions about the telematics system | Answers questions from customers about the telematics system |
| Contracting or canceling the TOYOTA Connect | Performs procedures to make or cancel a contract for customers |
| Confirming server or communication conditions | Confirms the TOYOTA Connect center condition |
| Re-registering a TOYOTA Connect device or telematics transceiver | Performs procedures for re-registration when the TOYOTA Connect device or telematics transceiver is replaced |
| Answering questions about a manual maintenance check for the emergency call service | Answers questions when a manual maintenance check for the emergency call service has not completed normally |
COMMUNICATION SYSTEM
USB Outline
Telematics system components communicate with each other via USB communication.
If a short or open circuit occurs in a USB communication line, communication will be interrupted and the system will not operate normally.
MOST Network Outline
Refer to System Description of Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>SYSTEM DESCRIPTION
CAN Communication Outline
Refer to System Description of Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>SYSTEM DESCRIPTION
DIAGNOSTIC FUNCTION OUTLINE
The telematics system has a diagnostic function (the result will be displayed on the master unit or GTS).
DIAGNOSIS DISPLAY DETAILED DESCRIPTION
This section contains a detailed description of displays in diagnostic mode.
Enter diagnostic mode.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Select "Service Information" on the "Service Menu" screen.
Select "MEU Information" from the "Service Information" screen.
Select "G-BOOK Information for Contract" on the "MEU Information" screen.
"G-BOOK Information for Contract" screen
| Display | Content |
|---|---|
| G-BOOK ID | The TOYOTA Connect ID of the navigation ECU assembly is displayed. |
| IMEI | The 15-digit serial number of the telematics transceiver is displayed. |
| FLAG | The TOYOTA Connect service flag of the navigation receiver assembly, navigation ECU assembly and telematics transceiver is displayed. |
Service flag description
| *a | Example |
Flag information display
| Display | Content |
|---|---|
| 1 | Under service contract is in progress |
| 0 | No service contract |
| X | The TOYOTA Connect service is suspended |
Flag information details
The content shown below is an example. Content varies depending on the specification of the vehicle.
| *1 | TOYOTA Connect contract flag | *2 | Vehicle stop position UP |
| *3 | Alarm report | *4 | Remote diagnosis |
| *5 | Remote customize | *6 | Remote warning |
| *7 | Remote immobiliser | *8 | Remote confirmation |
| *9 | Operation forgetting notification | *10 | Remote control |
| *11 | Gracenote service | *12 | Congestion forecast |
| *13 | Congestion forecast (time required) | *14 | Destination setting (set by TOYOTA Connect) |
| *15 | DRGSCC | *16 | Help net |
| *17 | DCM voice call | *18 | diagnosis trigger function |
| *19 | FFD function | *20 | Map on demand |
| *21 | Probe | *22 | My request |
| *23 | DCMOSS call | *24 | ESPO |
| *25 | ETC charge display | *26 | POI web search |
| *27 | Navi probe | *28 | Remote monitoring |
| *29 | Remote diagnosis recorder | *30 | G Traffic information automatic acquisition service |
| *31 | Remote DDR | *32 | Screen display |
| *33 | Position upload | *34 | Full browser |
| *35 | Center route | *36 | Remote maintenance notice |
| *37 | Center voice recognition | *38 | Stolen vehicle tracking |
| *39 | Usage based insurance | *40 | eConnect status change notification |
| *41 | Multimodal route searching | *42 | Recommend guidance |
| *43 | Server POI | *44 | Temporary map delivery |
| *45 | MM systems setting status | *46 | Vehicle info utilization: Collection |
| *47 | Vehicle info utilization: Delivery | *48 | Highway driving assist |
| *49 | Keyboard input support | - | - |
COMMUNICATION BASED VOICE RECOGNITION FUNCTION
There are two types of voice recognition; the voice recognition function uses voice recognition data stored in the onboard device. The other is communication based and uses voice recognition data sent from communication with the telematics transceiver as audio signals to be stored at the center.
Refer to the navigation system for information about voice recognition.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Communication Based Voice Recognition
By performing the voice recognition process at the center, natural language input and interactive voice operations besides the specified commands can be performed.
COMMUNICATION FUNCTION PAUSING
Before performing inspections or repairs which may cause warning messages or DTCs to occur, such as a simulation test or road test, it is necessary to activate warning notification restraint mode so that the TOYOTA Connect center does not recognize the warnings as real ones.
Communication function pausing mode can be entered by using the GTS or operating the multi-display assembly.
The warning notification function sends a warning ON signal, received from the combination meter assembly via CAN communication, to the TOYOTA Connect center using the TOYOTA Connect device if a warning is displayed in the vehicle due to a vehicle malfunction.
Communication function pausing mode
Communication function pausing mode (Using the GTS)
Enter the following menus: Body Electrical / Telematics
Use the GTS to cancel communication function pausing mode.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>UTILITY
Warning notification restraint mode (Using the multi-display)
Enter diagnostic mode of navigation system.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
To cancel communication function pausing mode, turn the ignition switch off and to ON to display the service mode screen and cancel communication function pausing mode.