Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2021.08
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0448454 THEFT DETERRENT SYSTEM D

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  SYSTEM DESCRIPTION  


OUTLINE OF THEFT DETERRENT SYSTEM


·

The theft deterrent system can be set by locking the doors using any of the following operations:

-

Entry lock operation

-

Wireless lock operation

-

Key linked lock operation*

-

By opening and closing the doors*

*: w/ Answer-back (Wireless Door Lock Buzzer) Function



·

In the armed state, the alarm function will be activated if one of the following conditions is met:

-

Any of the doors are unlocked.

-

Any of the doors, the hood or the luggage compartment door is opened.

-

The intrusion sensor (theft warning ultrasonic and tilt sensor) detects movement inside the cabin.

-

The tilt sensor (theft warning ultrasonic and tilt sensor) detects that the vehicle is tilted.*

*: Double Locking System



·

In the alarm sounding state, the system blinks the turn signal lights. At the same time, the system sounds the vehicle horns and theft warning siren assembly to deter break-in and theft as well as to warn people around the vehicle.

·

The theft deterrent system can be canceled by unlocking the doors using the following operation:

-

Entry unlock operation

-

Wireless unlock operation

-

Key linked unlock operation*

*: This function is set through the customize function.



·

The theft deterrent system has an active arming mode. There are 4 states in this mode: a disarmed state, an arming preparation state, an armed state and an alarm sounding state.


a.

Disarmed state:

·

The alarm function is not operating.

·

The theft deterrent system is not operating.



b.

Arming preparation state:

·

The time until the system goes into the armed state.

·

The theft deterrent system is not operating.



c.

Armed state:

·

The theft deterrent system is operating.



d.

Alarm sounding state:

·

The alarm function is operating.


Alarm time:

Approximately 27.5 seconds


Alarm Methods
Alarm Method Turn Signal Lights Blinking
Vehicle Horns Sounding
(approximately 0.4-second cycles)
Theft Warning Siren Assembly Sounding



FUNCTION OF MAIN COMPONENTS


Component Function
Security indicator light Informs driver of theft deterrent system status.
Theft warning siren assembly Sounds when attempted break-in or theft is detected.
Turn signal lights Blink when attempted break-in or theft is detected.
Vehicle horns Sound when attempted break-in or theft is detected.
·

Front door courtesy light switch assembly (for LH/RH)

·

Rear door courtesy light switch assembly (for LH/RH)


Detects door status (open or closed).
Door unlock detection switch Detects door status (locked or unlocked).
Hood lock assembly (hood courtesy switch) Detects hood status (open or closed).
Luggage compartment door lock assembly (luggage compartment door courtesy light switch) Detects luggage compartment door status (open or closed).
Intrusion sensor cancel switch
·

Sends a signal to the main body ECU (multiplex network body ECU) to cancel the intrusion sensor (theft warning ultrasonic and tilt sensor).

·

Sends a signal to the main body ECU (multiplex network body ECU) to cancel the tilt sensor (theft warning ultrasonic and tilt sensor).


Certification ECU (smart key ECU assembly)
·

Receives wireless door lock/unlock signal.

·

Receives entry door lock/unlock signal.


Intrusion sensor (theft warning ultrasonic and tilt sensor) Sends a signal to the main body ECU (multiplex network body ECU) to sound the alarm when detecting an intrusion.
Tilt sensor (theft warning ultrasonic and tilt sensor)* Sends a signal to the main body ECU (multiplex network body ECU) to sound the alarm when detecting a change in the pitch angle of the vehicle inclination.

*: w/ Double Locking System



ACTIVE ARMING MODE


a.

Active arming mode:

This system operates as described in the diagram below when one of the items for each condition is met.

HINT:

The term "all doors" used in this section refers to the driver door, front passenger door, rear door LH, rear door RH and luggage compartment door.


B163417E20
1.708,1.479 2.969,1.656 1.26,0.177 10 Disarmed State 1*1 5.01,1.5 6.271,1.677 1.26,0.177 10 Disarmed State 2*2 2.344,3.198 4.208,3.604 1.865,0.406 10 Arming Preparation State 2.75,4.604 3.563,4.781 0.813,0.177 10 Armed State 2.448,5.99 4.031,6.313 1.583,0.323 10 Alarm Sounding State 1.083,2.573 2.292,3.01 1.208,0.438 10 Condition [3] 2.99,2.573 4.031,2.979 1.042,0.406 10 Condition [1] 3.563,1.969 4.563,2.323 1,0.354 10 Condition [9] 3.542,1.323 4.49,1.5 0.948,0.177 10 Condition [10] 4.333,2.708 5.26,3.01 0.927,0.302 10 Condition [8] 3.76,5.302 4.833,5.615 1.073,0.313 10 Condition [4] 4.896,5.823 5.854,6.104 0.958,0.281 10 Condition [7] 0.333,6.875 3.49,7.042 3.156,0.167 10 *1: Disarmed state 1 is the normal disarmed state. 0.333,7.188 6.323,7.615 5.99,0.427 10 *2: Disarmed state 2 is set from disarmed state 1, the arming preparation state, the armed state or alarm sounding state. 4.885,4.458 5.875,4.771 0.99,0.313 10 Condition [7] 2.458,5.302 3.594,5.667 1.135,0.365 10 Condition [6] 0.479,5.792 1.51,6.094 1.031,0.302 10 Condition [5] 0.479,4.427 1.729,4.885 1.25,0.458 10 Condition [5] 3.76,3.906 4.792,4.292 1.031,0.385 10 Condition [2] 4.885,3.573 5.792,3.75 0.906,0.177 10 Condition [11] 1.042,0.854 2.073,1.042 1.031,0.188 10 Disarmed State

w/ Answer-back (Wireless Door Lock Buzzer) Function
Condition Item
Condition [1] In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met:
·

With all doors and the hood closed, all doors are locked by wireless operation, entry operation or key linked power door lock operation.

·

With all doors locked and the hood closed, the state changes from any of the doors being opened to all doors being closed.


Condition [2]
·

Allow approximately 30 seconds to elapse.


Condition [3] One of the following conditions is met:
·

All doors are unlocked by wireless operation, entry operation or key linked power door lock operation*.

·

Any door is unlocked.

·

Any door is opened.

·

The ignition switch is pushed.

·

The ignition switch is turned to ON or ACC.

·

The auxiliary battery is reconnected.


Condition [4] One of the following conditions is met:
·

The hood is opened when the hood is closed.

·

The intrusion sensor (theft warning ultrasonic and tilt sensor) detects movement within the vehicle.

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation, entry operation or key linked power door lock operation.

·

When 5 seconds or more have elapsed after the ignition switch is pressed, the power source mode is changed from off to ON without pressing the ignition switch.

·

The auxiliary battery is reconnected when the hood is open, any door is open or any door is unlocked.


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic and tilt sensor) using the intrusion sensor cancel switch.


Condition [5] One of the following conditions is met:
·

The ignition switch is turned on (READY).

·

All doors are unlocked by wireless operation, entry operation or key linked power door lock operation*.

·

The ignition switch is turned to ON or ACC within 5 seconds after the ignition switch is pushed.


Condition [6]
·

After approximately 27.5 seconds, the alarm stops and the system returns to the armed state.


Condition [7]
·

The luggage compartment door is opened by wireless operation or entry operation.


Condition [8] One of the following conditions is met:
·

The hood is closed with all the doors closed.

·

The luggage compartment door is closed with hood and all doors except for luggage compartment door closed.


Condition [9] One of the following conditions is met:
·

Any door is unlocked when all doors are locked.

·

Any door is opened.

·

The ignition switch is pushed.

·

The ignition switch is turned to ON or ACC.

·

The auxiliary battery is reconnected.

·

All doors are unlocked by wireless operation, entry operation or key linked power door lock operation*.


Condition [10] In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met:
·

With all doors closed and the hood open, all doors are locked by wireless operation, entry operation or key linked power door lock operation.

·

With all doors closed except for the luggage compartment door, the hood closed and the luggage compartment door is open, all doors are locked by wireless operation, entry operation or key linked power door lock operation.


In disarmed state 1, when the ignition switch is off and all doors are locked, the system state is switched if the following condition is met:
·

With hood closed and luggage compartment door open, the state changes from any of the doors being opened to all doors being closed.

·

With hood open and luggage compartment door closed, the state changes from any of the doors being opened to all doors being closed.


Condition [11]
·

The hood is opened.

·

The luggage compartment door is opened.

·

The luggage compartment door is opened by wireless operation or entry operation.



*: This function is set through the customize function.


w/o Answer-back (Wireless Door Lock Buzzer) Function
Condition Item
Condition [1] In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met:
·

With all doors and the hood closed, all doors are locked by wireless operation or entry operation.


Condition [2] Allow approximately 30 seconds to elapse.*3
Allow approximately 9 seconds to elapse.*4
Condition [3] One of the following conditions is met:
·

All doors are unlocked by wireless operation, entry operation or key linked power door lock operation*2.

·

Any door is unlocked.

·

Any door is opened.

·

The ignition switch is pushed.

·

The ignition switch is turned to ON or ACC.

·

The auxiliary battery is reconnected.


Condition [4] One of the following conditions is met:
·

The hood is opened when the hood is closed.

·

The intrusion sensor (theft warning ultrasonic and tilt sensor) detects movement within the vehicle.

·

The tilt sensor (theft warning ultrasonic and tilt sensor) detects a change in the pitch angle of the vehicle inclination.*1

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation or entry operation.

·

When 5 seconds or more have elapsed after the ignition switch is pressed, the power source mode is changed from off to ON without pressing the ignition switch.

·

The auxiliary battery is reconnected when the hood is open, any door is open or any door is unlocked.

·

The hood is open.

·

Any door is open.

·

The power source mode is ON.


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic and tilt sensor) using the intrusion sensor cancel switch.


Condition [5] One of the following conditions is met:
·

The ignition switch is turned on (READY).

·

All doors are unlocked by wireless operation, entry operation or key linked power door lock operation*2.


Condition [6]
·

After approximately 27.5 seconds, the alarm stops and 5 seconds later the system returns to the armed state.


Condition [7]
·

The luggage compartment door is opened by wireless operation or entry operation.


Condition [8] One of the following conditions is met:
·

The hood is closed with all the doors closed.

The luggage compartment door is closed with hood and all doors except for luggage compartment door closed.


Condition [9] One of the following conditions is met:
·

Any door is unlocked when all doors are locked.

·

Any door is opened.

·

The ignition switch is pushed.

·

The ignition switch is turned to ON or ACC.

·

The auxiliary battery is reconnected.

·

All doors are unlocked by wireless operation, entry operation or key linked power door lock operation*2.


Condition [10] In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met:
·

With all doors closed and the hood open, all doors are locked by wireless operation or entry operation.

·

With all doors closed except for the luggage compartment door, the hood closed and the luggage compartment door is open, all doors are locked by wireless operation or entry operation.


Condition [11]
·

The hood is opened.

·

The luggage compartment door is opened.

·

The luggage compartment door is opened by wireless operation or entry operation.



*1: w/ Double Locking System

*2: This function is set through the customize function.

*3: w/ Door Ajar Warning Buzzer Function

*4: w/o Door Ajar Warning Buzzer Function




FORCED DOOR LOCK CONTROL


a.

The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (armed state), all doors are forced to lock by a forced door lock signal.

i.

If the following conditions are met, the forced door lock control is operated.

·

The theft deterrent system is in the armed state.

·

Any door is unlocked.





PANIC ALARM CONTROL (w/ Panic Switch)


a.

Panic alarm control makes it possible to voluntarily set off the panic alarm by pressing the panic switch on the electrical key transmitter sub-assembly.

i.

Conditions that cause panic alarm control to set off the panic alarm:

The panic switch on the electrical key transmitter sub-assembly is pressed under the following conditions:

·

The ignition switch is off.

·

The theft deterrent system is not in the alarm sounding state.



ii.

Conditions that cause the panic alarm control to shut off the alarm:

Any of the following conditions is met during panic alarm control operation:

·

The ignition switch is turned to ON.

·

The panic switch is pressed again.

·

Any of the switches on the electrical key transmitter sub-assembly (lock/unlock/luggage compartment door open) is pressed.

·

The panic alarm ends (approximately 27.5 seconds have elapsed).

·

The theft deterrent system switches to the alarm sounding state. Under this condition, the theft deterrent system controls the alarm rather than the panic alarm control. In order to cancel this alarm, refer to the theft deterrent system alarm sounding state cancellation procedure.





INTRUSION SENSOR (THEFT WARNING ULTRASONIC AND TILT SENSOR)


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic and tilt sensor) using the intrusion sensor cancel switch.


a.

An intrusion sensor (theft warning ultrasonic and tilt sensor) is provided in the map light assembly located in the front of the vehicle interior.


b.

The main body ECU (multiplex network body ECU) activates the intrusion sensor (theft warning ultrasonic and tilt sensor) when the system changes from the disarmed state to the armed preparation state.

·

All windows are closed:

If an intrusion detection signal is input after the glass breakage signal is input from the intrusion sensor (theft warning ultrasonic and tilt sensor) during the armed state, the main body ECU (multiplex network body ECU) changes to the alarm state in order to output an alarm.

·

Any window is opened:

If an intrusion detection signal is input from the intrusion sensor (theft warning ultrasonic and tilt sensor) during the armed state, the main body ECU (multiplex network body ECU) changes to the alarm state in order to output an alarm.



c.

When the system is in the disarmed state, the function of the intrusion sensor (theft warning ultrasonic and tilt sensor) can be disabled by pressing the intrusion sensor cancel switch.


d.

The intrusion sensor (theft warning ultrasonic and tilt sensor) may erroneously detect intrusion in the following states:

·

Persons or pets are in the vehicle.

·

The vehicle is parked in a place where extreme vibrations or noises occur, such as in a parking garage.

·

Ice or snow is removed from the vehicle, causing the vehicle to receive repeated impacts or vibrations.

·

The wind or something similar causes an externally mounted reflectively coated windshield cover to move.

·

The intrusion sensor (theft warning ultrasonic and tilt sensor) may react to a hanger or other objects hanging in the cabin when they drop or swing.

·

The system changes to the armed state even when any of the windows is open. The intrusion sensor (theft warning ultrasonic and tilt sensor) may react to objects moving outside the vehicle when any of the windows is open.

·

The vehicle is inside an automatic or high-pressure car wash.

·

The vehicle experiences impacts, such as hail, lightning strikes and other kinds of repeated impacts or vibrations.




TILT SENSOR (THEFT WARNING ULTRASONIC AND TILT SENSOR) (w/ Double Locking System)


a.

The tilt sensor (theft warning ultrasonic and tilt sensor) detects the pitch angle of vehicle inclination using 2 deceleration sensors. When the tilt sensor (theft warning ultrasonic and tilt sensor) detects a change in the pitch angle of vehicle inclination, such as a thief attempting to tow the vehicle, it transmits the warning signal to the main body ECU (multiplex network body ECU).


b.

The main body ECU (multiplex network body ECU) activates the tilt sensor (theft warning ultrasonic and tilt sensor) when the system changes from the armed preparation state to the armed state. If a warning signal is received from the tilt sensor (theft warning ultrasonic and tilt sensor) when in the armed state, the main body ECU (multiplex network body ECU) changes to the alarm sounding state in order to sound the alarm.


c.

When the system is in the disarmed state, pressing the intrusion sensor cancel switch disables the function of the tilt sensor (theft warning ultrasonic and tilt sensor). If the system changes to the armed state, the tilt sensor (theft warning ultrasonic and tilt sensor) will not activate. This function is canceled each time all doors are unlocked by the wireless operation, entry and start system or key linked power door lock operation, and is reinstated when the tilt sensor (theft warning ultrasonic and tilt sensor) is on.


d.

Under the following conditions, if the vehicle tilts or acceleration in the vertical or horizontal direction is detected by the tilt sensor (theft warning ultrasonic and tilt sensor), the alarm may activate accidentally. To avoid accidental alarm activation, turn the tilt sensor (theft warning ultrasonic and tilt sensor) off using the intrusion sensor cancel switch.

·

The vehicle is transported by a ferry, trailer or train.

·

The vehicle is parked in a multi-story parking facility.

·

The vehicle is washed by a conveyor type car washing machine.

·

A tire blows out.

·

The vehicle is jacked up for a tire or wheel change.

·

An earthquake occurs or the road subsides.

·

Goods such as skis or snowboards are loaded or unloaded.




THEFT WARNING SIREN ASSEMBLY


a.

The theft warning siren assembly has an internal battery. If power to the theft warning siren assembly is interrupted or the communication line is open, the theft warning siren assembly detects it and sounds the alarm using the internal battery.


b.

The theft warning siren assembly has the following alarm controls: normal alarm control and open circuit alarm control. Under normal alarm control, the alarm sounds based on instructions from the main body ECU (multiplex network body ECU) whereas under open circuit alarm control, the theft warning siren assembly judges current security conditions and sounds the alarm by itself.

i.

Normal alarm control

The theft warning siren assembly sounds when the theft deterrent system is in the alarm sounding state and does not sound when the system is not in the alarm sounding state.

HINT:

If communication interruption between the theft warning siren assembly and main body ECU (multiplex network body ECU) continues for 70 seconds or more while the theft deterrent system is in the alarm sounding state, the theft warning siren assembly stops sounding.



ii.
B315877E02
0.083,0.083 2.979,0.458 2.896,0.375 10 false Conditions of theft warning siren assembly 1.292,0.875 2.26,1.125 0.969,0.25 10 false Disarmed State 1.385,2.219 2.323,2.469 0.938,0.25 10 false Armed State 0.958,1.667 1.104,1.813 0.146,0.146 10 false *1 2.448,1.677 2.729,1.854 0.281,0.177 10 false *2 0.458,3.177 2.99,3.531 2.531,0.354 10 false *1: Theft deterrent system changes to the armed state. 0.479,3.938 3.031,4.323 2.552,0.385 10 false *2: Theft deterrent system changes to the disarmed state.

Open circuit alarm control

The theft warning siren assembly changes between the disarmed state and armed state in accordance with the theft deterrent system changes between the disarmed state and armed state. If the power source, ground or communication line is open while the theft warning siren assembly is in the armed state, the theft warning siren assembly sounds.

During the open circuit alarm sounding state, the theft warning siren assembly sounds intermittently for 28 seconds and then stops for 5 seconds. This pattern repeats a maximum of 9 times.

The intermittent sounding will stop when either condition is met:

1. The theft warning siren assembly changes to the disarmed state.

2. The open circuit is returned to normal.

B267215E14
0.063,0.083 3.781,0.302 3.719,0.219 10 false (a) Intermittent sound pattern repeats a maximum of 9 times 0.229,0.427 2.74,0.635 2.51,0.208 10 false Theft warning siren is in the armed state 1.854,1.25 2.76,1.49 0.906,0.24 10 false Circuit is open 1.729,1.76 2.75,2 1.021,0.24 10 false Circuit is normal 1.031,2.063 3.469,2.302 2.438,0.24 10 false Theft warning siren sounds 0.729,2.573 2.802,2.823 2.073,0.25 10 false Theft warning siren sounds stop 1.854,8.031 2.76,8.271 0.906,0.24 10 false Circuit is open 1.729,8.552 2.75,8.781 1.021,0.229 10 false Circuit is normal 1.031,8.854 3.281,9.083 2.25,0.229 10 false Theft warning siren sounds 0.729,9.365 2.76,9.615 2.031,0.25 10 false Theft warning siren sounds stop 0.063,0.917 2.729,1.146 2.667,0.229 10 false Theft warning siren is in the disarmed state 0.26,7.219 2.75,7.438 2.49,0.219 10 false Theft warning siren is in the armed state 0.063,7.708 2.729,7.938 2.667,0.229 10 false Theft warning siren is in the disarmed state 1.854,4.719 2.76,4.927 0.906,0.208 10 false Circuit is open 1.729,5.229 2.75,5.469 1.021,0.24 10 false Circuit is normal 1.031,5.531 3.375,5.75 2.344,0.219 10 false Theft warning siren sounds 0.729,6.052 2.75,6.302 2.021,0.25 10 false Theft warning siren sounds stop 0.26,3.896 2.76,4.146 2.5,0.25 10 false Theft warning siren is in the armed state 0.063,4.396 2.74,4.604 2.677,0.208 10 false Theft warning siren is in the disarmed state 4.74,0.083 5.833,0.281 1.094,0.198 10 false T1: 28 seconds 3.344,2.417 3.531,2.563 0.188,0.146 10 false T1 3.531,2.885 3.719,3.031 0.188,0.146 10 false T2 3.333,5.885 3.521,6.031 0.188,0.146 10 false T1 3.333,9.188 3.521,9.333 0.188,0.146 10 false T1 3.531,9.656 3.719,9.802 0.188,0.146 10 false T2 6.052,0.083 6.948,0.344 0.896,0.26 10 false T2: 5 seconds 0.063,3.229 2.604,3.458 2.542,0.229 10 false (b) The open circuit is returned to normal 0.24,3.51 4.094,3.74 3.854,0.229 10 false (1) The open circuit is returned to normal within 28 seconds 0.24,6.792 4.969,7.021 4.729,0.229 10 false (2) The open circuit is returned to normal after 28 seconds or more elapsed




SECURITY INDICATOR LIGHT OUTPUT


a.

According to the state of the theft deterrent system, the main body ECU (multiplex network body ECU) outputs a signal to turn the security indicator light on. However, some of the actual lighting conditions of the security indicator light are different from the output signals of the main body ECU (multiplex network body ECU).

Output
State of Theft Deterrent System Security Indicator Light
Output Signal from Main Body ECU (Multiplex Network Body ECU) Actual Lighting Condition
Disarmed state (1), (2) Off
·

Off (Immobiliser function unset)

·

Blinking (Immobiliser function set)


Arming preparation state On On
Armed state Off Blinking
Alarm sounding state On On

Blinking Cycle
Time Security Indicator Light
0.125 seconds On
1.875 seconds Off

HINT:

When the immobiliser function is set, the security indicator light blinks during both the disarmed state and the armed state due to output signals from the immobiliser function.




CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC AND TILT SENSOR)


*1: w/ Door Ajar Warning Buzzer Function

*2: w/o Door Ajar Warning Buzzer Function


NOTICE:

Perform the intrusion sensor (theft warning ultrasonic and tilt sensor) operation inspection with the GTS disconnected.


a.

Check that the hood is closed.


b.

Check the intrusion sensor (theft warning ultrasonic and tilt sensor) operation (customize setting "Intrusion Sensor Sound Detection Function" is "ON").

i.

Turn the ignition switch off.


ii.

Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state) (all windows need to be opened).


iii.

Wait 30*1 or 9*2 seconds after locking all the doors using the wireless door lock or entry door lock function and check that the security indicator light blinks (armed state). Then, make a loud sound by hitting metal objects together (jangle a bunch of keys, etc.) near the intrusion sensor (theft warning ultrasonic and tilt sensor) in the vehicle and check that the theft deterrent system alarm operates due to movement inside the vehicle.

HINT:

If the electrical key transmitter is within the entry exterior area at this time, the alarm does not operate due to the intrusion sensor.



iv.

Perform an unlock operation using the wireless or entry operation to stop the alarm.



c.

Check the intrusion sensor (theft warning ultrasonic and tilt sensor) operation (customize setting "Intrusion Sensor Sound Detection Function" is "OFF").

i.

Turn the ignition switch off.


ii.

Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state) (all windows need to be opened).


iii.

Wait 30*1 or 9*2 seconds after locking all the doors using the wireless door lock or entry door lock function and check that the security indicator light blinks (armed state). Then, check that the theft deterrent system alarm operates due to movement inside the vehicle.

HINT:

If the electrical key transmitter is within the entry exterior area at this time, the alarm does not operate due to the intrusion sensor.



iv.

Perform an unlock operation using the wireless or entry operation to stop the alarm.




CHECK INTRUSION SENSOR OFF SWITCH


*1: w/ Door Ajar Warning Buzzer Function

*2: w/o Door Ajar Warning Buzzer Function


NOTICE:

Perform the intrusion sensor (theft warning ultrasonic and tilt sensor) operation inspection with the GTS disconnected.


a.

Check that the hood is closed.


b.

Check the intrusion sensor OFF switch operation (customize setting "Intrusion Sensor Sound Detection Function" is "ON").

i.

Turn the ignition switch off.


ii.

Press the intrusion sensor OFF switch and check that "Theft Sensor Turned OFF" is displayed on the combination meter.


iii.

Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state).


iv.

Approximately 30*1 or 9*2 seconds after locking all the doors via wireless operation or smart operation, check that the security indicator light changes to blinking (armed state). Also, after making a metal-on-metal striking sound (such as by shaking keys) near the sensor, check that the auto alarm warning does not operate according to movement in the cabin. At this time, do not bring the electrical key transmitter sub-assembly close to the smart exterior area.

HINT:

Even if the intrusion sensor (theft warning ultrasonic and tilt sensor) is off, the theft deterrent system is in the armed state. Therefore, if any of the doors is manually unlocked, the alarm operates.




c.

Check the intrusion sensor OFF switch operation (customize setting "Intrusion Sensor Sound Detection Function" is "OFF").

i.

Turn the ignition switch off.


ii.

Press the intrusion sensor OFF switch and check that "Theft Sensor Turned OFF" is displayed on the combination meter.


iii.

Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state).


iv.

Approximately 30*1 or 9*2 seconds after locking all the doors via wireless operation or smart operation, check that the security indicator light changes to blinking (armed state) and the auto alarm does not operate according to movement in the cabin. At this time, do not bring the electrical key transmitter sub-assembly close to the smart exterior area.

HINT:

Even if the intrusion sensor (theft warning ultrasonic and tilt sensor) is off, the theft deterrent system is in the armed state. Therefore, if any of the doors is manually unlocked, the alarm operates.