Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2021.08
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0490698 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1785  Front Occupant Classification Sensor LH Collision Detection  


DESCRIPTION

DTC B1785 is stored when the occupant detection ECU receives a collision detection signal sent by the front occupant classification sensor LH in the case of an accident.

DTC B1785 is also stored when the front seat assembly RH is subjected to a strong impact, even if an actual accident did not occur.

If the vehicle was not in a collision, but the occupant detection ECU receives a collision detection signal and stores DTC B1785, the DTC can be cleared by performing zero point calibration.

Therefore, if DTC B1785 is output, first perform zero point calibration.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1785 Front Occupant Classification Sensor LH Collision Detection
·

Front occupant classification sensor LH sensed large load.

·

Front seat adjuster assembly RH malfunction


Front seat adjuster assembly RH (Front occupant classification sensor LH)* Occupant Detection A

*: The front occupant classification sensor LH is built into the front seat adjuster assembly RH.


CAUTION / NOTICE / HINT

CAUTION:

When this DTC is stored, repair of the malfunction indicated can only be performed by initializing the occupant detection ECU or replacing the front seat adjuster assembly RH. Do not replace the occupant detection ECU to repair the malfunction indicated by this DTC.

If the occupant detection ECU is replaced, this DTC will not be output but the occupant detection system may not function properly.


NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

When RoB X2102 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1785 is output, perform troubleshooting for this DTC first.


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION


Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435
OK:

"Zero Point Calibration is complete." is displayed.



Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

6.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
2.CLEAR DTC
a.

Clear the DTCs stored in the occupant detection ECU.

Body Electrical > Occupant Detection > Clear DTCs
50002 394

Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 10 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > Occupant Detection > Trouble Codes
50001 394

Result:
Result Proceed to
B1785 is not output A
B1785 is output B


HINT:

Codes other than DTC B1785 may be output at this time, but they are not related to this check.


Post-procedure1

a.

None



A

END (NORMAL AFTER PERFORMING ZERO POINT CALIBRATION)

B

4.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
4.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Replace the front seat adjuster assembly RH with a new one.

HINT:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY



d.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

5.PERFORM ZERO POINT CALIBRATION
5.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION


Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END (FRONT SEAT ADJUSTER ASSEMBLY RH WAS DEFECTIVE)

6.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Replace the front seat adjuster assembly RH with a new one.

HINT:

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY



d.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION


Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END (FRONT SEAT ADJUSTER ASSEMBLY RH WAS DEFECTIVE)