FAIL-SAFE FUNCTION
When communication fails in any of the CAN bus lines (communication lines), a fail-safe function(s) will operate. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.
The following table shows the effects on each system when communication is impossible. (For further details, see the pages for each system.)
| Function | Control Master
(ECU that mainly determines control) |
Related ECU | Behavior when Communication Impossible | Driver is Notified | DTC
(ECU that stored DTC) |
|---|---|---|---|---|---|
| Blind Spot Monitor
(Detects neighboring vehicles that are in outer mirror blind spots and notifies drivers of the existence of these vehicles.) |
Blind spot monitor sensor RH (B) | ·
Airbag ECU assembly ·
Main body ECU (multiplex network body ECU) ·
Rear television camera assembly ·
Central gateway ECU (network gateway ECU) ·
Clearance warning ECU assembly ·
Brake booster assembly (No. 1 skid control ECU) ·
EV control ECU ·
Forward recognition camera ·
Parking assist ECU ·
Combination meter assembly ·
Steering sensor |
The last value is maintained | Displayed on multi-information display | ·
U0125 ·
U0126 ·
U0129 ·
U0142 ·
U0293 (Blind spot monitor sensor RH [B]) |
| Camera Detection Function
(Monitors the shift position signal and vehicle speed, detects pedestrians in camera video while reversing, and displays a warning on the display while sounding the buzzer.) |
Rear television camera assembly | ·
Brake booster assembly (No. 1 skid control ECU) ·
EV control ECU ·
Steering sensor |
·
Warning operating: Warning display and buzzer operation are prohibited after they end ·
Warning not operating: Warning display and buzzer operation are prohibited |
Displayed on multi-information display | ·
U0126 ·
U0129 ·
U0293 (Rear television camera assembly) |
| Main body ECU (multiplex network body ECU) | ·
Warning operating: Warning display and buzzer operation are prohibited after they end ·
Warning not operating: Warning display and buzzer operation are prohibited |
Displayed on multi-information display | U0140
(Rear television camera assembly) |
||
| Blind spot monitor sensor RH (B) | ·
Warning operating: Warning buzzer immediately prohibited (warning display operates normally) ·
Warning not operating: Normal operation (buzzer operation is prohibited) |
Displayed on multi-information display | U0233
(Rear television camera assembly) |
||
| Controls Video Output to Display
·
Supplies power ·
Displays the screen on the multi-media display ·
Sets the reaction pattern |
Rear television camera assembly | Main body ECU (multiplex network body ECU) | Switch icons, guide lines, cooperative display and all other displays are hidden | Attention mark is displayed on the camera screen | U0140
(Rear television camera assembly) |
·
Radio receiver assembly ·
Radio and display receiver assembly |
Switch icons on the screen are grayed out | Attention mark is displayed on the camera screen | U0163
(Rear television camera assembly) |
||
| Guide Line Display Control
·
Vehicle path display according to the steering wheel angle ·
Screen control according to back door status ·
Changes the path according to the mechanism |
Rear television camera assembly | ·
Steering sensor ·
Rack and pinion power steering gear assembly |
Some guide lines are not displayed | Attention mark is displayed on the camera screen | ·
U0126 ·
U0131 (Rear television camera assembly) |
| Main body ECU (multiplex network body ECU) | Some switch icons are grayed out | Attention mark is displayed on the camera screen | U0140
(Rear television camera assembly) |
||
| Cooperative Display Control
·
Sonar Cooperative Display ·
Rear cross traffic alert cooperative display |
Rear television camera assembly | ·
Clearance warning ECU assembly ·
Blind spot monitor sensor RH (B) |
Nothing | Nothing | ·
U0233 ·
U1110 (Rear television camera assembly) |
| Gasoline Model/HV Model Judgment Control
(Uses engine/HV information to switch the turning characteristics pattern.) |
Rear television camera assembly | EV control ECU | The previous values are maintained | Attention mark is displayed on the camera screen | U0293
(Rear television camera assembly) |
| 2WD/4WD Judgment Control
(Uses 2WD/4WD information to switch the turning characteristics pattern.) |
Rear television camera assembly | EV control ECU | The previous values are maintained | Attention mark is displayed on the camera screen | U0293
(Rear television camera assembly) |
| EPS Variation Judgment Control
(Uses EPS information to switch the turning characteristics pattern.) |
Rear television camera assembly | Rack and pinion power steering gear assembly | The previous values are maintained | Attention mark is displayed on the camera screen | U0131
(Rear television camera assembly) |
| Steering Wheel Judgment Control
(Uses steering wheel information to switch the switch icon arrangement pattern on the screen.) |
Rear television camera assembly | Main body ECU (multiplex network body ECU) | The previous values are maintained | Attention mark is displayed on the camera screen | U0140
(Rear television camera assembly) |
| Destination Determination Control
(Switches the screen display pattern according to destination information.) |
Rear television camera assembly | Main body ECU (multiplex network body ECU) | The previous values are maintained | Attention mark is displayed on the camera screen | U0140
(Rear television camera assembly) |
| VGRS Availability Judgment Control
(Uses VGRS information to switch the turning characteristics pattern.) |
Rear television camera assembly | Steering sensor | The previous values are maintained | Attention mark is displayed on the camera screen | U0126
(Rear television camera assembly) |
| Communication Stop Counter
(Monitors the NS and NM frames of all ECUs connected to the same CAN bus connected with the central gateway ECU (network gateway ECU), and detects ECU communication stops.) |
Central gateway ECU (network gateway ECU) | All ECUs connected to the same CAN bus connected with the gateway ECU | The communication stop durations of monitored NS and NM frames are stored | Nothing | Nothing |
| Clearance Sonar
(Uses the buzzer and display to notify the driver of any stationary objects to the front sides, front, rear and sides of the vehicle, as well as the approximate distance to the object, when the vehicle is driven at low speed (less than approximately 10 km/h).) |
Clearance warning ECU assembly | ·
Steering sensor ·
Brake actuator assembly (No. 2 skid control ECU) ·
EV control ECU |
Operation is stopped | ·
Displayed on multi-information display ·
CSR off indicator illuminates ·
Meter buzzer sounds |
·
U012687 ·
U012987 ·
U029387 (Clearance warning ECU assembly) |
| Parking assist ECU | Only clearance sonar used for detection (camera not used) | CSR off indicator illuminates | U117987
(Clearance warning ECU assembly) |
||
| Combination meter assembly | System on/off and other customization not possible (operates using previous value) | Nothing | U015587
(Clearance warning ECU assembly) |
||
| Parking Support Brake
(Reduces the risk of damage during collisions by providing warnings, controlling drive torque and performing brake control, when there is a possibility of contact with stationary objects, vehicles approaching from the rear or pedestrians behind the vehicle, when driving forward or backward.) |
Clearance warning ECU assembly | ·
Steering sensor ·
Brake actuator assembly (No. 2 skid control ECU) ·
EV control ECU |
·
Before control: Control is prohibited. ·
During control: Control is continued |
·
Displayed on multi-information display ·
PKSB off indicator illuminates ·
Meter buzzer sounds |
·
U012687 ·
U012987 ·
U029387 (Clearance warning ECU assembly) |
·
Blind spot monitor sensor LH (A) ·
Blind spot monitor sensor RH (B) ·
Rear television camera assembly |
·
Before control: Parking support brake (rear approaching vehicle) control is prohibited. ·
During control: Parking support brake (rear approaching vehicle) control is continued. |
·
Displayed on multi-information display ·
PKSB off indicator illuminates ·
Meter buzzer sounds |
·
U117787 ·
U117887 ·
U026587 (Clearance warning ECU assembly) |
||
| Advanced Park
(Uses ultrasonic wave sensors installed to the front, rear and sides of the vehicle to detect empty spaces, and uses a television camera assembly installed to the outer mirror to detect parking lines and empty spaces, in order to support parking operations by providing steering operation, accelerator operation, brake operation, display to the multi-information display and operation guidance using the buzzer and speech, during reverse parking and parallel departure.) |
Clearance warning ECU assembly | ·
Shift control ECU ·
Steering sensor ·
Brake actuator assembly (No. 2 skid control ECU) ·
Rack and pinion power steering gear assembly ·
Main body ECU (multiplex network body ECU) ·
EV control ECU ·
Rack and pinion power steering gear assembly ·
Parking assist ECU |
·
Before control: Control is prohibited. ·
During control: Control is stopped. |
·
Before control: Displayed on the multi-information display. ·
During control: Displayed on the multi-information display. |
·
U010387 ·
U012687 ·
U012987 ·
U013187 ·
U014087 ·
U029387 ·
U110687 ·
U117987 (Clearance warning ECU assembly) |
·
Air conditioning amplifier assembly ·
Combination meter assembly |
·
Before control: Control is prohibited. ·
During control: Control is continued |
·
Before control: Displayed on the multi-information display. ·
During control: Not display. |
·
U015587 ·
U016487 (Clearance warning ECU assembly) |
||
| Pre-collission Safety System
·
Recognizes the obstacles, sounds warning buzzer and performs brake assist and brake control to avoid collisions. ·
If the system determines that collision avoidance via steering would be effective, collision avoidance assist via steering is performed. |
Forward recognition camera | ·
Steering sensor ·
Brake actuator assembly (No. 2 skid control ECU) ·
EV control ECU ·
Airbag ECU assembly ·
Millimeter wave radar sensor assembly ·
Rack and pinion power steering gear assembly |
·
Pre-collission brake assist, pre-collission warning buzzer, pre-collission brake, emergency steering avoidance assist and low-speed acceleration control are canceled. ·
Pre-collission safety system is stopped. |
·
PSC off indicator light illuminates ·
Displayed on multi-information display |
·
U012587 ·
U012687 ·
U012987 ·
U023587 ·
U023A87 ·
U029387 ·
U013187 ·
U041881 ·
U030051 ·
U030057 ·
U032851 ·
U032857 (Forward recognition camera) |
| Lane Tracing Assist System
(Recognizes the lane with the front camera and assists the vehicle in driving the center of the road.) |
Forward recognition camera | ·
EV control ECU ·
Combination meter assembly ·
Brake actuator assembly (No. 2 skid control ECU) ·
Steering sensor ·
Millimeter wave radar sensor assembly ·
Rack and pinion power steering gear assembly ·
Airbag ECU assembly |
Control is stopped | ·
LTA indicator illuminates (amber) ·
Displayed on multi-information display |
·
U012587 ·
U012687 ·
U012987 ·
U013187 ·
U015587 ·
U023587 ·
U029387 ·
U030051 ·
U030057 (Forward recognition camera) |
| Automatic High Beam/Adaptive High Beam
(Uses the front camera to recognize front headlights and taillights and sends that target information to the control ECU.) |
Forward recognition camera | ·
Main body ECU (multiplex network body ECU) ·
EV control ECU ·
Brake actuator assembly (No. 2 skid control ECU) ·
Millimeter wave radar sensor assembly ·
Steering sensor |
The previous values are maintained | Displayed on multi-information display | ·
U012687 ·
U012987 ·
U014087 ·
U023587 ·
U029387 (Forward recognition camera) |
| Front Camera
(Sends the common calculation and recognition result to each application in the forward recognition camera.) |
Forward recognition camera | ·
Main body ECU (multiplex network body ECU) ·
EV control ECU ·
Brake actuator assembly (No. 2 skid control ECU) ·
Airbag ECU assembly ·
Steering sensor |
·
The previous values are maintained ·
Recognition is disabled |
Nothing | ·
U012587 ·
U012687 ·
U012987 ·
U014087 ·
U029387 (Forward recognition camera) |
| Dynamic Radar Cruise Control System
(The dynamic radar cruise control system uses the millimeter wave radar sensor assembly, steering angle sensor, etc., to recognize and judge the existence of a preceding vehicle, track it while ensuring an appropriate vehicle-to-vehicle distance until the vehicle is stopped. When there are no preceding vehicles, this system allows for constant-speed driving at the set speed.) |
Forward recognition camera | ·
Millimeter wave radar sensor assembly ·
Brake actuator assembly (No. 2 skid control ECU) ·
Airbag ECU assembly ·
Steering sensor ·
EV control ECU ·
Combination meter assembly |
Radar cruise control system is stopped | Displayed on multi-information display | ·
U012587 ·
U012687 ·
U012987 ·
U015587 ·
U023587 ·
U029387 ·
U110687 (Forward recognition camera) |
| Preceding Vehicle Start Notification
(Recognizes a preceding vehicle using the forward recognition camera and millimeter wave radar sensor assembly, detects that the preceding vehicle has started off, and then notifies the driver.) |
Forward recognition camera | ·
Millimeter wave radar sensor assembly ·
EV control ECU ·
Combination meter assembly ·
Brake actuator assembly (No. 2 skid control ECU) |
Preceding vehicle start notification is stopped. | Displayed on multi-information display | ·
U012987 ·
U015587 ·
U023587 ·
U029387 (Forward recognition camera) |
| Sign Display Function
(Uses the front camera to recognize signs, and displays recognized signs on the combination meter assembly or meter mirror (HUD ECU).) |
Forward recognition camera | Combination meter assembly | Sign information is not displayed on the meter | Displayed on multi-information display | U015587
(Forward recognition camera) |
| Notification Function
·
The driver is notified if the speed limit displayed by the vehicle exceeds a certain threshold. ·
Notifies the driver if it detects a passing operation by the driver when a no overtaking/passing sign is output. ·
The driver is notified if it is detected that the vehicle is being driven into a no entry zone when a no entry sign is recognized. |
Forward recognition camera | Combination meter assembly | The notification function is not implemented | Displayed on multi-information display | U015587
(Forward recognition camera) |
| Customization Function
(Customization function that turns road sign assist on/off when the steering switch is operated, and changes the excessive speed notification method/level, no overtaking/passing notification method, etc.) |
Forward recognition camera | Combination meter assembly | Customization settings cannot be changed | Displayed on multi-information display | U015587
(Forward recognition camera) |
| Electronic Power Steering
(Calculates the current to be used for steering assist according to the torque sensor value and vehicle speed, and then operates the motor.) |
Rack and pinion power steering gear assembly | EV control ECU | Before assist: Steering assist does not start. Assist starts when the vehicle speed reaches 4 km/h. | Nothing | ·
U029300 ·
U029387 (Rack and pinion power steering gear assembly) |
| During assist: None. | Nothing | ·
U029300 ·
U029387 (Rack and pinion power steering gear assembly) |
|||
| Brake actuator assembly (No. 2 skid control ECU) | Control is performed temporarily with the steering assist amount set to when the vehicle speed is 100 km/h | EPS indicator illuminates | ·
U012900 ·
U012987 (Rack and pinion power steering gear assembly) |
||
| The steering wheel center point is not learned if there is a problem with CAN communication | Nothing | Nothing | |||
| Airbag ECU assembly | The steering wheel center point is not learned if there is a problem with CAN communication | Nothing | Nothing | ||
| Steering sensor | Steering feels worse (compensation control using the steering angle is stopped) | Nothing | Nothing | ||
| Assist Map Selection
(Selects the assist map to be used according to the destination, drive system (2WD, 4WD) and engine type before shipping from the factory or switching the ECU.) |
Rack and pinion power steering gear assembly | ·
EV control ECU ·
Main body ECU (multiplex network body ECU) ·
Brake actuator assembly (No. 2 skid control ECU) |
·
A temporary map is used to perform assist as an assist map cannot be selected according to vehicle specifications. ·
Steering feel may be unusual |
EPS indicator illuminates | Nothing |
| VDIMα System
(Calculates the current to be used for steering assist according to the command value from the brake actuator assembly (No. 2 skid control ECU), and then operates the motor.) |
Brake actuator assembly (No. 2 skid control ECU) | Brake actuator assembly (No. 2 skid control ECU) | VDIMα control ends | Nothing | ·
U012900 ·
U012987 (Rack and pinion power steering gear assembly) |
| VDIMβ System
(Calculates the current to be used for steering assist according to the command value from the brake actuator assembly (No. 2 skid control ECU) and VGRS, and then operates the motor.) |
Brake actuator assembly (No. 2 skid control ECU) | Brake actuator assembly (No. 2 skid control ECU) | VDIMβ control ends | EPS indicator illuminates | ·
U012900 ·
U012987 (Rack and pinion power steering gear assembly) |
| Lane-keeping Assist System
(Calculates the current to be used for steering assist according to the torque command from the forward recognition camera, and then operates the motor.) |
Forward recognition camera | Forward recognition camera | Lane-keeping assist system control ends | Nothing | ·
U023A00 ·
U023A87 (Rack and pinion power steering gear assembly) |
| Pedestrian Protection Function (PUH)
(Pops up the hood to protect the pedestrian when a collision with a pedestrian occurs.) |
Airbag ECU assembly | Brake actuator assembly (No. 2 skid control ECU) | Control is prohibited. | Pedestrian protection warning illuminates | U012987
(Airbag ECU assembly) |
| The previous determined value is maintained. | Nothing | Nothing | |||
| Steering sensor | Reception stop: Steering angle set to 0. | Pedestrian protection warning illuminates | U012687
(Airbag ECU assembly) |
||
| Cycle error: Previous determined value is maintained. | Nothing | Nothing | |||
| Prevention Link
(Obtains information from the PCS and uses it for side airbag deployment control.) |
Airbag ECU assembly | ·
Forward recognition camera ·
Millimeter wave radar sensor assembly |
Nothing | ·
SRS warning light illuminates ·
Equipped with pedestrian protection system: Pedestrian protection warning illuminates |
·
U023587 ·
U023A87 ·
U110487 (Airbag ECU assembly) |
| Air Conditioning Control
·
Corrects the engine speed by performing idle up, etc. ·
Adjusts the air temperature, airflow mode and airflow volume according to the engine coolant temperature ·
Performs engine coolant temperature map calibration and switches the compressor lock judgment value based on engine type |
EV control ECU | Air conditioning amplifier assembly | ·
While the ignition switch is ON, control is performed using the default engine coolant temperature value (80°C) ·
While the ignition switch is ON, control is performed using the default engine type ·
None when the ignition switch is not ON |
MIL illuminates for battery cooling OBD vehicle only | U0293
(Air conditioning amplifier assembly) |
| Simple Load Control
(Limits simple electrical load control according to the load control level.) |
Rack and pinion power steering gear assembly | Air conditioning amplifier assembly | ·
While the ignition switch is ON, previous values are maintained (during a reset, there is no load control) ·
None when the ignition switch is not ON |
Nothing | U0131
(Air conditioning amplifier assembly) |
| Panel Control
(Controls the air conditioning system operation status and panel switch IND output according to panel switch operation information) |
·
Radio receiver assembly ·
Radio and display receiver assembly |
Air conditioning amplifier assembly | ·
While the ignition switch is ON and the panel switch is turned off, exhaust gas availability information is maintained ·
None when the ignition switch is not ON |
Nothing | U0163
(Air conditioning amplifier assembly) |
| Destination Determination Control
(Switches the A/C control pattern according to the destination information) |
Main body ECU (multiplex network body ECU) | Air conditioning amplifier assembly | ·
While the ignition switch is ON, previous values are maintained ·
None when the ignition switch is not ON |
Nothing | U0142
(Air conditioning amplifier assembly) |
| Ambient Temperature Compensation Control
(Changes the air conditioning system operation status and adjusts the ambient temperature display output value according to vehicle speed information) |
Combination meter assembly | Air conditioning amplifier assembly | ·
While the ignition switch is ON, control is performed with the default vehicle speed value ·
None when the ignition switch is not ON |
Nothing | U0155
(Air conditioning amplifier assembly) |
| Air Conditioning ECO Control
(Performs ECO-mode control) |
EV control ECU | Air conditioning amplifier assembly | ·
While the ignition switch is ON, previous values are maintained ·
After a reset, the system stays in its normal state of operation |
Nothing | Nothing |
| Air Conditioning Screen Operation in TOYOTA Multi Operation Touch | Integration control sub-assembly | Air conditioning amplifier assembly | Nothing | Nothing | U1114
(Air conditioning amplifier assembly) |
| Pre-air Conditioning Control | Certification ECU (smart key ECU assembly) | Air conditioning amplifier assembly | Nothing | Nothing | U0327
(Air conditioning amplifier assembly) |
| Battery Cooling Control | Battery ECU assembly | Air conditioning amplifier assembly | Nothing | MIL illuminates for battery cooling OBD vehicle only | U0111
(Air conditioning amplifier assembly) |
| Clearance Sonar Settings
(Sets clearance sonar screen notification conditions.) |
·
Radio receiver assembly ·
Radio and display receiver assembly |
Clearance warning ECU assembly | Transitions to the last screen | Nothing | ·
U0073 ·
U1110 (Radio receiver assembly, Radio and display receiver assembly) |
| Rear View Monitor Control
(Displays the rear camera view.) |
·
Radio receiver assembly ·
Radio and display receiver assembly |
EV control ECU | Changes to the multi-media display DTC user screen only during camera mode (displays the camera screen) | ·
Changes to the multi-media display user screen only during camera mode (displays the camera screen) ·
Cannot switch to the camera screen |
U0073
(Radio receiver assembly, Radio and display receiver assembly) |
| Smart Camera Function
(Superimposes the estimated course lines of the vehicle, vehicle width extension lines and distance guide lines over the rear camera image on the display when the vehicle is driven in reverse.) |
·
Radio receiver assembly ·
Radio and display receiver assembly |
Rear television camera assembly | ·
Changes to the multi-media display user screen or multi-media display DTC screen only during camera DTC mode (displays the camera DTC screen) ·
Only when camera malfunction DTC C1610 is output: The current DTC (C1610) is cleared ·
The temporary values for the reactive force setting completion notification and pointer coordinates are sent. The camera screen pattern is treated as a temporary value, and the reaction force setting operates at camera image release. ·
Camera screen pattern is treated as default value |
·
Displays the camera diagnostic screen ·
Changes to the multi-media display user screen only during camera mode (displays the camera screen) |
·
U0073 ·
U0265 (Radio receiver assembly, Radio and display receiver assembly) |
| EV control ECU | Changes to the multi-media display user screen only during camera mode (displays the camera screen) | ·
Changes to the multi-media display user screen only during camera mode (displays the camera screen) ·
Cannot switch to the camera screen |
U0073
(Radio receiver assembly, Radio and display receiver assembly) |
||
| Peripheral Monitoring Function
(ECUs for the multiple camera system, etc.) |
·
Radio receiver assembly ·
Radio and display receiver assembly |
Parking assist ECU | ·
Changes to the multi-media display user screen or multi-media display DTC screen only during camera DTC mode (displays the camera DTC screen) ·
Only when camera malfunction DTC C1610 is output: The current DTC (C1610) is cleared ·
The temporary values for the reactive force setting completion notification and pointer coordinates are sent. The camera screen pattern is treated as a temporary value, and the reaction force setting operates at camera image release. ·
Camera screen pattern is treated as default value |
Displays the camera diagnostic screen | ·
U0073 ·
U023B (Radio receiver assembly, Radio and display receiver assembly) |
| EV control ECU | Changes to the multi-media display user screen only during camera mode (displays the camera screen) | ·
Changes to the multi-media display user screen only during camera mode (displays the camera screen) ·
Cannot switch to the camera screen |
U0073
(Radio receiver assembly, Radio and display receiver assembly) |
||
| Destination Determination
(Uses the destination information (including steering wheel information) to determine the driver seat or passenger seat and to determine whether the XM function is enabled.) |
·
Radio receiver assembly ·
Radio and display receiver assembly |
Main body ECU (multiplex network body ECU) | The destination is determined according to the last received value and the system is operated accordingly (if there is no last received value, the system operates using the default value) | The time zone and language selection screens do not match the destination | ·
U0073 ·
U0140 (Radio receiver assembly, Radio and display receiver assembly) |
| Navigation Coordinated Control (Air Conditioning)
(Automatically switches between fresh air mode and recirculated air mode based on information from the navigation system indicating whether the vehicle is in a tunnel.) |
Radio and display receiver assembly | Air conditioning amplifier assembly | Nothing | Menu settings for air conditioning coordinated control (control for changing air conditioning from fresh air mode to recirculated air mode when entering tunnel) are cleared | ·
U0073 ·
U0164 (Radio receiver assembly) |
| Vehicle Customize Function
(Allows changing of operation and control conditions for vehicle functions (illumination time, etc.).) |
·
Radio receiver assembly ·
Radio and display receiver assembly |
·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly |
Determined that remote tool communication permission is allowed | Nothing | U0073
(Radio receiver assembly, Radio and display receiver assembly) |
·
Air conditioning amplifier assembly ·
Main body ECU (multiplex network body ECU) ·
Certification ECU (smart key ECU assembly) ·
Position Control ECU Assembly |
3 retries are performed (including the first time) | ·
The applicable customization item is grayed out and the operation is prohibited ·
The applicable customization item is not displayed |
·
B15F5 ·
B15F6 ·
B15F7 ·
B15F8 (Radio receiver assembly, Radio and display receiver assembly) |
||
| Main body ECU (multiplex network body ECU) | ·
The entrance button is grayed out and cannot be selected when a communication stop occurs, even when customize information is received 1 or more times within 5 seconds after the ignition switch is turned to ON ·
Customization is performed for the applicable customization item according to diagnostic communication when customize information is not received within 5 seconds after the ignition switch is turned to ON |
The entrance button is grayed out and cannot be selected | U0073
(Radio receiver assembly, Radio and display receiver assembly) |
||
| Combination Meter Link Function
(Changes the display based on the customization information set on the combination meter assembly. Outputs the customization information set in the system.) |
·
Radio receiver assembly ·
Radio and display receiver assembly |
Combination meter assembly | ·
Linked language, unit and accent color: The last valid state is maintained ·
GS search: Control is performed as if there is an unconfirmed GS search request ·
The last set value is maintained. ·
If the setting item is displayed, it is grayed out so that the item cannot be changed. |
Function linking with the combination meter assembly cannot be performed | ·
U0073 ·
U0155 (Radio receiver assembly, Radio and display receiver assembly) |
| Information Volume Adjustment or Stop Function
(Receives flags from the driving support ECU to operate the alarm and mutes multi-media audio while the alarm is in operation.) |
·
Radio receiver assembly ·
Radio and display receiver assembly |
·
Forward recognition camera ·
Millimeter wave radar sensor assembly |
Audio mute is canceled
(Indicates the normal state (mute cancel) to the command switch unit) |
Nothing | U0073
(Radio receiver assembly, Radio and display receiver assembly) |
| Predictive Eco Support | ·
Radio receiver assembly ·
Radio and display receiver assembly |
EV control ECU | ·
Accumulation processing, etc. is prohibited ·
Information sent via CAN is initialized ·
Display of setting switch is prohibited. ·
Information display is prohibited. |
Nothing | ·
U0073 ·
U0293 (Radio receiver assembly, Radio and display receiver assembly) |
| Brake actuator assembly (No. 2 skid control ECU) | Nothing | Nothing | ·
U0073 ·
U0129 (Radio receiver assembly, Radio and display receiver assembly) |
||
| DSSS
·
Signal information provision service ·
Regulation information provision service ·
Obstacle information provision service |
·
Radio receiver assembly ·
Radio and display receiver assembly |
EV control ECU | The following functions that reference the accelerator position do not operate
·
Red light warning ·
Temporary stop warning |
Infrastructure-linked icons of the following functions are not displayed
·
Red light warning ·
Temporary stop warning |
·
U0073 ·
U0293 (Radio receiver assembly, Radio and display receiver assembly) |
| Clock Function | ·
Radio receiver assembly ·
Radio and display receiver assembly |
Combination meter assembly | Clock is not displayed | Nothing | Nothing |
| Battery Control
(Calculates the battery permitted charge/discharge.) |
Battery ECU assembly | EV control ECU | Batteryless | Master warning light illuminates | ·
U029387 ·
U115087 (Battery ECU assembly) |
| Key-linked Door Lock
(Locks and unlocks all doors with a key-linked switch operation.) |
Main body ECU (multiplex network body ECU) | Airbag ECU assembly | The driver buckle switch signal is set to "Unconfirmed" | Even if the driver seat belt is fastened when the ignition switch is ON, the doors can be locked and unlocked using the key-linked switch | U0151
(Main body ECU [multiplex network body ECU]) |
| Shift-linked Auto Lock
(Locks all doors by changing the shift position from P to other than P.) |
Main body ECU (multiplex network body ECU) | EV control ECU | The shift position P signal is set to "OFF" | All doors are not locked if the following conditions are met
Precondition:
The ignition switch is ON and all doors are closed Operation condition:
Shift position is changed from P to other than P |
U0101
(Main body ECU [multiplex network body ECU]) |
| Shift-linked Auto Unlock
(Unlocks all the doors by changing the shift position from other than P to P.) |
Main body ECU (multiplex network body ECU) | EV control ECU | The shift position P signal is set to "OFF" | All doors are not locked if the following conditions are met
Precondition:
The ignition switch is ON and all doors are closed Operation condition:
Shift position is changed from P to other than P |
U0101
(Main body ECU [multiplex network body ECU]) |
| Combination meter assembly | The vehicle speed signal (from the combination meter to other systems) is set to "0" | All doors are not locked if the following conditions are met
Precondition:
The ignition switch is ON and all doors are closed Operation condition:
Shift position is changed from P to other than P |
U0155
(Main body ECU [multiplex network body ECU]) |
||
| Vehicle Speed-linked Auto Lock
(Locks all doors automatically when it is determined that the vehicle is in motion.) |
Main body ECU (multiplex network body ECU) | Combination meter assembly | The vehicle speed signal (from the combination meter to other systems) is set to "0" | All doors are not locked if the following conditions are met
Precondition:
Ignition switch ON Operation condition:
Vehicle speed is 20 km/h or higher |
U0155
(Main body ECU [multiplex network body ECU]) |
| Manual Unlock Prohibition
(Prohibits manual unlock when the vehicle condition has been determined to be in the parked condition after passengers have exited the vehicle and the door lock and door closing operation has been detected.) |
Main body ECU (multiplex network body ECU) | EV control ECU | READY signal is set to "Not displayed" | Manual unlock prohibition is not canceled even when the ignition switch is ON (READY) in manual unlock prohibition status | U0293
(Main body ECU [multiplex network body ECU]) |
| Auto-lock Switching
(Switches each auto-lock and auto-unlock function on/off according to user operation.) |
Main body ECU (multiplex network body ECU) | EV control ECU | The shift position P signal is set to "OFF" | Shift-linked auto-lock and shift-linked auto-unlock on/off switching are performed using the shift P signal ON. Therefore, the on/off switch cannot be operated even if the following procedures are performed
1.
Turn the ignition switch from off to ON. 2.
Change the shift position to P Hold down the manual lock (when auto-locked) or unlock (when auto-unlocked) for 3 to 7 seconds 3.
After answer back is performed, shift-linked auto-lock/shift-linked auto-unlock will switch between on and off |
U0101
(Main body ECU [multiplex network body ECU]) |
| Wireless Door Lock/Unlock/Auto Relock/Panic/2-times Operation Unlock
(Locks or unlocks doors according to the wireless key switch operation. Relocks doors in order to prevent theft when a lock is unintentionally opened due to a wireless key unlock switch being operated incorrectly.) |
Main body ECU (multiplex network body ECU) | Certification ECU (smart key ECU assembly) | Communication is set to the default value | Wireless door lock/unlock does not operate | Nothing |
| Smart Door Lock/Unlock
(Locks or unlocks the door via smart operation.) |
Main body ECU (multiplex network body ECU) | Certification ECU (smart key ECU assembly) | Communication is set to the default value | Wireless door lock/unlock does not operate | U0327
(Main body ECU [multiplex network body ECU]) |
| Wireless Buzzer
(Sounds the answer back function when the wireless door lock and unlock operations are performed.) |
Main body ECU (multiplex network body ECU) | Certification ECU (smart key ECU assembly) | ·
The wireless buzzer sounding signal is set to the "Default value" ·
Wireless buzzer volume is set to "Maximum" |
No answer back occurs when the wireless door lock and unlock operations are performed | U0327
(Main body ECU [multiplex network body ECU]) |
| Smart Trunk Opener
(Unlatches the trunk after the trunk is unlocked when the trunk open switch is pressed and held in the trunk lock position.) |
Main body ECU (multiplex network body ECU) | Certification ECU (smart key ECU assembly) | ·
The trunk/back door opener switch signal is set to "OFF" ·
Communication is set to the default value |
The trunk does not unlatch even when the trunk open switch is held down with the trunk locked | U0327
(Main body ECU [multiplex network body ECU]) |
| Trunk Opener
(Unlatches the trunk according to the open switch being pressed on the instrument panel.) |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Trunk open control is prohibited | Nothing | U0155
(Main body ECU [multiplex network body ECU]) |
| EV control ECU | ·
The back door operation start and answer back hazard warning light/buzzer do not operate ·
One motion power back door does not operate |
The trunk is not unlatched even if the luggage compartment door opening switch assembly is pressed and held | U0101
(Main body ECU [multiplex network body ECU]) |
||
| Washer Nozzle Heater
(Prevents the washer nozzle from freezing due to low temperature.) |
Main body ECU (multiplex network body ECU) | Air conditioning amplifier assembly | Ambient temperature data (display) is set to "Unconfirmed" | The nozzle heater does not operate even if the ambient temperature is 5°C or lower | Nothing |
| Seat and Mirror Control
·
Memorizes and recalls memory switch ·
Memorizes and recalls memory call |
Main body ECU (multiplex network body ECU) | ·
Position Control ECU Assembly ·
Multiplex Tilt and Telescopic ECU ·
Front multiplex network door ECU LH ·
Brake actuator assembly (No. 2 skid control ECU) ·
Combination meter assembly |
Commands the seat, tilt and telescopic, etc. to stop operating | Nothing | ·
U0155 ·
U0199 ·
U0200 ·
U0208 ·
U1106 ·
U1115 (Main body ECU [multiplex network body ECU]) |
| Certification ECU (smart key ECU assembly) | Memory call registration: The operation is stopped due to a timeout while waiting for the verification results | Nothing | U0327
(Main body ECU [multiplex network body ECU]) |
||
| Dome Light
(The dome light illuminates when approaching any door while carrying the smart key.) |
Main body ECU (multiplex network body ECU) | Certification ECU (smart key ECU assembly) | The exterior illumination result signal is set to the "Default value" | Outside handle light and dome light do not illuminate when approaching one of the doors while holding the smart key | U0327
(Main body ECU [multiplex network body ECU]) |
| Interior Illumination Dimming
(Dims the instrument panel, foot light and inside handle illumination when starting to drive.) |
Main body ECU (multiplex network body ECU) | EV control ECU | The shift position P signal is set to "OFF" | The interior illumination does not dim when changing the shift position from P to other than P | U0101
(Main body ECU [multiplex network body ECU]) |
| Interior Illumination Color Switching
(Switches instrument panel/foot light/inside steering wheel illumination color when driving (ignition switch ON) via the TOYOTA Multi Operation Touch Panel switches.) |
Main body ECU (multiplex network body ECU) | Integration control sub-assembly | Switch information for the TOYOTA Multi Operation Touch Panel is set to "OFF" | Color does not change even if the TOYOTA Multi Operation Touch Panel color switching switch is pressed | U1114
(Main body ECU [multiplex network body ECU]) |
| Reverse-linked Mirror
(Changes the direction of the outer mirror when the shift position is changed to R.) |
Main body ECU (multiplex network body ECU) | EV control ECU | The shift position R signal is set to "OFF" | The reverse-linked mirror does not operate when the shift position is changed to R | U0101
(Main body ECU [multiplex network body ECU]) |
| Daytime Running Light
(Turns on or off the daytime running lights after determining whether the vehicle is driving.) |
Main body ECU (multiplex network body ECU) | ·
Headlight ECU sub-assembly LH ·
Headlight ECU sub-assembly RH |
Nothing | When the headlight ECU is equipped, the daytime running lights do not turn on | Nothing |
| Brake actuator assembly (No. 2 skid control ECU) | The electric parking brake lock condition is set to "Condition unknown" | For daytime running lights other than the Scandinavian specification, the daytime running lights do not illuminate even if the parking break is released | Nothing | ||
| Alarm Function
(When the alarm is set, this determines unauthorized intrusion according to a change in the door courtesy status and gives a warning.) |
Main body ECU (multiplex network body ECU) | Nothing | Nothing | Security indicator does not blink | Nothing |
| Certification ECU (smart key ECU assembly) | The push start switch signal is set to "OFF" and the push start key signal is set to "Push start system control key unconfirmed" | If the push start switch is pressed before the alarm is set, the alarm is not unset. However, the alarm is set when a certain amount of time elapses after a wireless lock operation is performed.
When the warning alarm is sounding, the alarm is not canceled even when certifying with the smart key registered to the vehicle and pressing the push start switch. |
U0120
(Main body ECU [multiplex network body ECU]) |
||
| EV control ECU | READY signal is set to "Not displayed" | When the warning alarm is sounding, the alarm is not canceled even with the ignition switch is ON (READY) | Nothing | ||
| Battery Saver
(Cancels illumination commands sent to the interior illumination and stops the power supply to suppress battery depletion when the system determines that the vehicle is parked.) |
Main body ECU (multiplex network body ECU) | Certification ECU (smart key ECU assembly) | The exterior illumination result signal is set to the "Default value" | During battery protection, battery protection is not canceled and illumination does not turn on even when the user approaches a door while carrying the smart key | U0327
(Main body ECU [multiplex network body ECU]) |
| Light Automatic Turn-off System
(Automatically turns lights off when exiting the vehicle with the lights still turned on.) |
Main body ECU (multiplex network body ECU) | Certification ECU (smart key ECU assembly) | Communication is set to the default value | When the wireless key lock switch is pressed while waiting for the light off delay time (30 seconds) with all the doors locked, the headlights do not turn off | U0327
(Main body ECU [multiplex network body ECU]) |
| Steering sensor | Previous values maintained for the light combination switch location information | Even if the light combination switch is operated while waiting until lights are automatically turned off or while lights are automatically being turned off, the headlights and taillights do not turn off | U0126
(Main body ECU [multiplex network body ECU]) |
||
| LED Headlight Warning
(Notifies the driver when the system detects an open circuit in the LED headlight or a driver malfunction.) |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Nothing | Unable to send LED headlight indicator illumination status (illumination status depends on the fail-safe specification of the combination meter assembly) | Nothing |
| EV control ECU | READY signal is set to "Not displayed" | Even if the low beams are on with the ignition switch ON (READY) while an LED malfunction is detected, the LED headlight indicator does not illuminate | U0293
(Main body ECU [multiplex network body ECU]) |
||
| Automatic Display Dimming
(Determines the time of day (daytime, twilight to nighttime) according to the light sensor signal and interior illumination state as time changes from twilight to nighttime and links with the tail cancel switch state to dim the interior displays and indica |
Main body ECU (multiplex network body ECU) | ·
Steering sensor ·
Radio receiver assembly ·
Radio and display receiver assembly ·
Clearance warning ECU assembly |
Nothing | Cannot dim (due to fail-safe operation of receiving ECU) | Nothing |
| Combination meter assembly | The tail cancel signal is set to "OFF" | Dimming is performed even when the tail cancel switch is on | U0155
(Main body ECU [multiplex network body ECU]) |
||
| Power Window Operation Permission
(Permits operation of the power windows for 43 seconds after the ignition switch is turned off.) |
Main body ECU (multiplex network body ECU) | EV control ECU | READY signal is set to "Not displayed" | Power window operation is not permitted even when the ignition switch is ON (READY)
(Ignition switch ON is one of the OR conditions required for operation permission in practice) |
U0293
(Main body ECU [multiplex network body ECU]) |
| Wireless Power Window
(Operates the power windows according to wireless key operation.) |
Main body ECU (multiplex network body ECU) | Certification ECU (smart key ECU assembly) | Communication is set to the default value | When the ignition switch is turned off, power windows cannot be operated up or down using wireless key switch | Nothing |
| Window Open Warning
(Displays the open window warning on the combination meter and sounds a single buzzer to remind the user to close the windows when exiting the vehicle with the windows open.) |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Nothing | Even if the ignition switch is turned off and the driver door is opened with a window open, the open window warning is not displayed on the meter | Nothing |
| Sliding Roof Open Warning
(Displays the open window warning on the combination meter and sounds a single buzzer to remind the user to close the sliding roof when exiting the vehicle with the sliding roof open.) |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Nothing | Even if the ignition switch is turned off and the driver door is opened with the sliding roof open, the sliding roof open warning is not displayed on the meter | Nothing |
| Tire Pressure Warning
(Displays tire pressure warning on the meter.) |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Nothing | Tire pressure warning is not correctly displayed on the combination meter assembly.
(This follows the fail-safe specification of the combination meter assembly) |
Nothing |
| Auto Power Retract Mirror
(Retracts/returns the outer mirrors in conjunction with the doors locking/unlocking.) |
Main body ECU (multiplex network body ECU) | ·
Front multiplex network door ECU LH ·
Front multiplex network door ECU RH |
Nothing | Automatic or manual electric retraction of the outer mirrors does not operate | Nothing |
| Certification ECU (smart key ECU assembly) | Communication is set to the default value | The outer mirrors are not retracted/returned in conjunction with wireless/smart lock/unlock operations | Nothing | ||
| Headlight Illumination Reminder
(Reminds the user to illuminate the headlights when the vehicle is driven at night with the headlights turned off.) |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Nothing | When the vehicle is driven at night with the headlight switch off or in the TAIL position, the light illumination reminder is not displayed on the multi-information display | Nothing |
·
The vehicle speed signal (from the combination meter to other systems) is set to "0" ·
Response type is set to unused ·
Response content is set to unused |
When the vehicle is driven at night with the headlight switch off or in the TAIL position, the light illumination reminder is not displayed on the multi-information display | U0155
(Main body ECU [multiplex network body ECU]) |
|||
| Headlight Turn Off Reminder
(Reminds the user to turn off the headlights when the headlight switch is on and 5 minutes elapse after the ignition switch is turned off.) |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Nothing | Even if the headlight switch is on and 5 minutes elapse after the ignition switch is turned off, the reminder to turn off the light is not displayed on the multi-information display | Nothing |
·
Response type is set to unused ·
Response content is set to unused |
The reminder does not disappear even if the steering switch return button is pressed within 6 seconds of the reminder display | Nothing | |||
| Wiper-linked Window Close
(Proposes to close the windows when the wipers are operating.) |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Nothing | Even if a window is open while the wipers are operating, the reminder to close the window is not displayed on the multi-information display | Nothing |
·
Response type is set to unused ·
Response content is set to unused |
For the contents displayed on the multi-information display, after the steering switch responds, the system does not operate according to the response contents | Nothing | |||
| Certification ECU (smart key ECU assembly) | Communication is set to the default value | When a wireless/smart-linked power window UP/DOWN operation is performed, the reminder does not disappear | Nothing | ||
| Ignition Switch Off-linked Window Close
(Proposes to close the window when exiting the vehicle.) |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Nothing | Even if the ignition switch is turned off with a window open, the reminder to close the window is not displayed on the multi-information display | Nothing |
·
Response type is set to unused ·
Response content is set to unused |
For the contents displayed on the multi-information display, after the steering switch responds, the system does not operate according to the response contents | Nothing | |||
| Certification ECU (smart key ECU assembly) | Communication is set to the default value | When a wireless/smart-linked power window UP/DOWN operation is performed, the reminder does not disappear | Nothing | ||
| Power Window Unlock Reminder
(Reminds the user to release the power window lock switch when the power window lock switch is ON and the power window switch is operated.) |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Nothing | The power window lock switch release reminder is not displayed on the multi-information display even when the power window lock switch is on and the power window switch is operated | Nothing |
| Door Open-linked Wiper Stop
(Stops the wipers when a door is opened while the wipers are operating.) |
Main body ECU (multiplex network body ECU) | Brake actuator assembly (No. 2 skid control ECU) | The electric parking brake lock condition is set to "Condition unknown" | When the ignition switch is ON, the wipers are operating in AUTO mode and the shift position is in P, the wipers do not stop even if the driver or passenger door is opened | Nothing |
| EV control ECU | The shift position P signal is set to "OFF" | When the ignition switch is ON, the wipers are operating in AUTO mode and the electric parking brake is locked, the wipers do not stop even if the driver or passenger door is opened | U0101
(Main body ECU [multiplex network body ECU]) |
||
| Diagnostic/C-BEST
(Diagnostic phase 4 communication) |
Nothing | All ECUs connected to CAN | Exits diagnostic mode | Nothing | Nothing |
| Smart Beam
(Controls high beam output automatically when the smart beam sensor detects a preceding or oncoming vehicle.) |
Main body ECU (multiplex network body ECU) | Headlight ECU sub-assembly LH | System does not operate
(The meter indicator blinks) |
The meter indicator blinks | U0182
(Main body ECU [multiplex network body ECU]) |
| Forward recognition camera | System does not operate
(The meter indicator blinks) |
The meter indicator blinks | U023A
(Main body ECU [multiplex network body ECU]) |
||
| Rear Seat Reminder
(Determines that something was left on the rear seat when a rear door is opened or closed. Provides notification when the driver exits the vehicle to prevent something from being left on the rear seat.) |
Main body ECU (multiplex network body ECU) | EV control ECU | READY signal is set to "Not displayed" | After turning the ignition switch to ON (READY), the rear seat reminder notification is not displayed even after turning the ignition switch off | U0293
(Main body ECU [multiplex network body ECU]) |
| Light Control
(Controls light illumination based on the light illumination request from the main body ECU (multiplex network body ECU).) |
·
Front multiplex network door ECU LH ·
Front multiplex network door ECU RH |
Main body ECU (multiplex network body ECU) | Door mirror foot light does not operate | Door mirror foot light does not operate | Nothing |
| Mirror Operation Control
(Controls operation of the outer mirror based on mirror switch information, etc. from the main body ECU (multiplex network body ECU).) |
·
Front multiplex network door ECU LH ·
Front multiplex network door ECU RH |
Main body ECU (multiplex network body ECU) | The mirrors cannot be operated manually | The mirrors cannot be operated manually | U0142
(Front multiplex network door ECU LH, Front multiplex network door ECU RH) |
| Mirror Heater Control
(Controls operation of the outer mirror heater based on defogger switch information, etc. from the air conditioning amplifier assembly.) |
·
Front multiplex network door ECU LH ·
Front multiplex network door ECU RH |
·
Air conditioning amplifier assembly ·
Main body ECU (multiplex network body ECU) |
Mirror heater does not operate | Mirror heater does not operate | U0142
(Front multiplex network door ECU LH, Front multiplex network door ECU RH) |
| Mirror Power Retract Control
(Controls power retraction operation of the outer mirror based on mirror switch information, etc. from the main body ECU (multiplex network body ECU).) |
·
Front multiplex network door ECU LH ·
Front multiplex network door ECU RH |
Main body ECU (multiplex network body ECU) | Mirror power retract does not operate | Mirror power retract does not operate | Nothing |
| Mirror Reverse Control
(Controls reverse operation of the outer mirror based on the reverse request from the main body ECU (multiplex network body ECU).) |
·
Front multiplex network door ECU LH ·
Front multiplex network door ECU RH |
Main body ECU (multiplex network body ECU) | Mirror reverse-linked function does not operate | Mirror reverse-linked function does not operate | Nothing |
| Mirror Memorization and Recall Control
(Stores the mirror surface position of the outer mirror and controls recall operation to the stored position based on the memory request from the main body ECU (multiplex network body ECU).) |
·
Front multiplex network door ECU LH ·
Front multiplex network door ECU RH |
Main body ECU (multiplex network body ECU) | ·
Mirror recall function does not operate ·
Mirror memorization function does not operate |
·
Mirror recall function does not operate ·
Mirror memorization function does not operate |
Nothing |
| Memory Switch Signal Substitute Transmission (Driver Side)
(Sends memory switch signals via CAN.) |
Main body ECU (multiplex network body ECU) | Nothing | Nothing | Memory system
The memory store and memory recall functions (mirror, driver seat, tilt and telescopic) do not operate |
Nothing |
| Door Closer Control
(Monitors the condition of the doors and completely closes a door when it is ajar.) |
·
Front multiplex network door ECU LH ·
Front multiplex network door ECU RH ·
Rear multiplex network door ECU LH ·
Rear multiplex network door ECU RH |
Nothing | Nothing | The door lock may operate during closer operation, and it may unlock at that time.
The door lock has a retry function, which effectively locks the doors. |
Nothing |
| Door closer does not operate | Door closer does not operate | U0142
(Rear multiplex network door ECU LH, Rear multiplex network door ECU RH) |
|||
| Air Conditioner
(Operates air conditioning functions according to operations of the touch panel switches in the display.) |
Air conditioning amplifier assembly | Air conditioning amplifier assembly | Switches in the display do not operate | Switches in the display do not operate | U0164
(Integration control sub-assembly) |
| Drive Mode Switch Information Output
(Switches the drive mode according to operations of the touch panel switches in the display.) |
EV control ECU | EV control ECU | Switches in the display do not operate | Switches in the display do not operate | U0100
(Integration control sub-assembly) |
| Night-time Dimmer
(Controls the lighting according to whether the lighting is dimmed/not dimmed at night.) |
Main body ECU (multiplex network body ECU) | Main body ECU (multiplex network body ECU) | Not dimmed | Does not dim | U0142
(Integration control sub-assembly) |
| Vehicle Speed Signal Receiver
(The touch panel receives the vehicle speed signal.) |
Combination meter assembly | Combination meter assembly | Nothing | Nothing | U0155
(Integration control sub-assembly) |
| Multi-media Link
(Switches the language of the TOYOTA Multi Operation Touch Panel when the multi-media language is switched.) |
Radio receiver assembly | Radio receiver assembly | Language not linked | Language not linked | U0163
(Integration control sub-assembly) |
| Camera Screen Display Request (Panoramic View Monitor System)
(Displays the camera screen on the TOYOTA Multi Operation Touch Panel.) |
Parking assist ECU | Parking assist ECU | Nothing | Nothing | U023B
(Integration control sub-assembly) |
| Camera Screen Display Request (Parking Assist Monitor System)
(Displays the camera screen on the TOYOTA Multi Operation Touch Panel.) |
Rear television camera assembly | Rear television camera assembly | Nothing | Nothing | U0265
(Integration control sub-assembly) |
| Seat Position Memorize/Recall
(Stores the seat position by operating the switch on the door. Also, moves each movement location to its stored position.) |
Main body ECU (multiplex network body ECU) | ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly ·
Multiplex Tilt and Telescopic ECU |
Operation of moving parts is stopped | Nothing | Nothing |
| Memory Call Recall
(Automatically moves to the driving position associated with the electrical key when the driver door is opened.) |
Main body ECU (multiplex network body ECU) | ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly ·
Multiplex Tilt and Telescopic ECU |
Operation of moving parts is stopped | Nothing | Nothing |
| Away/Return Function
(Slides the seat rearward when exiting the vehicle. It also moves it to the position it was in prior to entering the vehicle.) |
Main body ECU (multiplex network body ECU) | ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly |
Operation of moving parts is stopped | Nothing | Nothing |
| Air Conditioning Control
(Assists with transferring signals between the air conditioning amplifier assembly and compressor.) |
EV control ECU | ·
Air conditioning amplifier assembly ·
Main body ECU (multiplex network body ECU) |
Nothing | Nothing | ·
U014087 ·
U016487 (EV Control ECU) |
| Regenerative Brake Coordinated Control
(Attempts to increase the amount of energy recovered as much as possible by coordinating with the brake actuator assembly (No. 2 skid control ECU).) |
EV control ECU | Brake actuator assembly (No. 2 skid control ECU) | Nothing | Nothing | U117087
(EV Control ECU) |
| Driving Control, Cruise Control
(Adjusts the brake actuator assembly (No. 2 skid control ECU), and automatically controls the vehicle speed.) |
EV control ECU | Brake actuator assembly (No. 2 skid control ECU) | Nothing | Nothing | U012987
(EV Control ECU) |
| Vehicle Damage Determination
(Determines whether there was a collision according to the airbag signal.) |
EV control ECU | Airbag ECU assembly | Nothing | Nothing | U015187
(EV Control ECU) |
| Electronic Ignition Switch Control
(Changes the ignition switch mode and sends starter drive requests according to ignition switch operation.) |
Certification ECU (smart key ECU assembly) | Main body ECU (multiplex network body ECU) | Nothing | "Advice for starting" cannot be displayed | U0140
(Certification ECU [smart key ECU assembly]) |
| Nothing | "Advice for starting" cannot be displayed | Nothing | |||
| Air conditioning amplifier assembly | Nothing | Pre-air conditioning does not operate | U0164
(Certification ECU [smart key ECU assembly]) |
||
| Brake actuator assembly (No. 2 skid control ECU) | Nothing | When the vehicle power source is turned from on to off, the push smart system telltale blinks red due to a vehicle speed information malfunction. | ·
U0129 ·
B2282 (Certification ECU [smart key ECU assembly]) |
||
| Nothing | Nothing | B2284
(Certification ECU [smart key ECU assembly]) |
|||
| EV control ECU | Nothing | ·
For plug-in vehicles only, the ignition switch does not turn off when the AC charging plug is connected while the ignition switch is ON (READY) ·
Starting is not possible after 3 seconds have elapsed after turning the ignition switch to ON, the ignition switch is turned off via push switch operation. Starting is possible with the ignition switch turned off. ·
"Restart advice while driving" cannot be displayed after emergency stop |
Nothing | ||
| Nothing | Nothing | ·
U0100 ·
U0293 (Certification ECU [smart key ECU assembly]) |
|||
| Shift control ECU | Nothing | It will take 1 or 2 seconds for the ignition switch to turn off | U0103
(Certification ECU [smart key ECU assembly]) |
||
| Composition Control of Video from 4 Cameras | Parking assist ECU | Rear television camera assembly | ·
The display area from the rear cameras is blacked out ·
Advanced park cannot start ·
Performed until parking is completed during advanced park control |
Attention mark is displayed on the camera screen | U026587
(Parking assist ECU) |
| Controls video output to display | Parking assist ECU | Main body ECU (multiplex network body ECU) | ·
Hides guide lines and cooperative display, etc. ·
Switch is grayed out ·
Advanced park cannot start ·
Control stops during advanced park control |
Attention mark is displayed on the camera screen | U014087
(Parking assist ECU) |
·
Radio receiver assembly ·
Radio and display receiver assembly |
·
Switch is grayed out ·
Advanced park cannot start ·
Performed until parking is completed during advanced park control |
Attention mark is displayed on the camera screen | U016387
(Parking assist ECU) |
||
| Screen Switching Control | Parking assist ECU | ·
Brake actuator assembly (No. 2 skid control ECU) ·
Main body ECU (multiplex network body ECU) ·
EV control ECU |
·
Hides the camera screen (displayed in some cases) ·
Advanced park cannot start ·
Control stops during advanced park control |
Attention mark is displayed on the camera screen | ·
U012987 ·
U014087 ·
U029387 (Parking assist ECU) |
| Guide Line Display Control | Parking assist ECU | Steering sensor | Driving forward:
·
Some guide lines are cleared ·
The guide line switching switch is grayed out Driving in reverse:
·
Some guide lines are cleared ·
Advanced park cannot start |
Attention mark is displayed on the camera screen | U012687
(Parking assist ECU) |
| Main body ECU (multiplex network body ECU) | Driving in reverse:
·
All guide lines are cleared when driving in reverse ·
Grays out the guide line display mode switch ·
Advanced park system cannot start ·
Some guide lines are cleared |
Attention mark is displayed on the camera screen | U014087
(Parking assist ECU) |
||
| Rack and pinion power steering gear assembly | Driving forward:
·
Some guide lines are cleared ·
The guide line switching switch is grayed out Driving in reverse:
·
Some guide lines are cleared ·
Advanced park cannot start |
Attention mark is displayed on the camera screen | U013187
(Parking assist ECU) |
||
| Cooperative Display Control for Other Parts | Parking assist ECU | Clearance warning ECU assembly | ·
No sonar cooperative display ·
Advanced park cannot start ·
Control stops during advanced park control |
Nothing | U111087
(Parking assist ECU) |
| Blind spot monitor sensor RH (B) | No RCTA cooperative display | Nothing | U023387
(Parking assist ECU) |
||
| Forward recognition camera | No FCTA cooperative display | Nothing | U023A87
(Parking assist ECU) |
||
| ENG/HV Judgment Control | Parking assist ECU | EV control ECU | ·
The previous values are maintained ·
Advanced park cannot start ·
Control stops during advanced park control |
Attention mark is displayed on the camera screen | ·
U010087 ·
U029387 (Parking assist ECU) |
| 2WD/4WD Judgment Control | Parking assist ECU | EV control ECU | ·
The previous values are maintained ·
Advanced park cannot start ·
Control stops during advanced park control |
Attention mark is displayed on the camera screen | ·
U010087 ·
U029387 (Parking assist ECU) |
| AT/MT Judgment Control | Parking assist ECU | EV control ECU | ·
The previous values are maintained ·
Advanced park cannot start ·
Control stops during advanced park control |
Attention mark is displayed on the camera screen | ·
U010087 ·
U029387 (Parking assist ECU) |
| EPS variation judgment control | Parking assist ECU | Rack and pinion power steering gear assembly | The previous values are maintained | Attention mark is displayed on the camera screen | U013187
(Parking assist ECU) |
| Steering Wheel Judgment Control | Parking assist ECU | Main body ECU (multiplex network body ECU) | ·
The previous values are maintained ·
Advanced park cannot start ·
Control stops during advanced park control |
Attention mark is displayed on the camera screen | U014087
(Parking assist ECU) |
| Parking Assist Monitor System Judgment Control | Parking assist ECU | Rear television camera assembly | ·
The previous values are maintained ·
Advanced park cannot start ·
Performed until parking is completed during advanced park control |
Attention mark is displayed on the camera screen | U026587
(Parking assist ECU) |
| Meter
(Displays advice and warnings.) |
Combination meter assembly | Shift control ECU | The last value is maintained | Nothing | U010387
(Combination meter assembly) |
| Steering sensor | Turns off. | Nothing | U012687
(Combination meter assembly) |
||
| Brake actuator assembly (No. 2 skid control ECU) | Speedometer does not operate | ·
ABS warning light illuminates ·
VSC warning light illuminates ·
BRAKE warning light illuminates |
U012987
(Combination meter assembly) |
||
| Rack and pinion power steering gear assembly | Nothing | EPS warning light illuminates | U013187
(Combination meter assembly) |
||
| Main body ECU (multiplex network body ECU) | The last value is maintained | Nothing | U014287
(Combination meter assembly) |
||
| Airbag ECU assembly | Nothing | A/B warning light illuminates | U015587
(Combination meter assembly) |
||
| Nothing | Pedestrian protection system warning light illuminates | Nothing | |||
| Not displayed | Nothing | Nothing | |||
·
Radio receiver assembly ·
Radio and display receiver assembly |
Turns off. | Nothing | U016387
(Combination meter assembly) |
||
| Air conditioning amplifier assembly | "--" is displayed for the ambient temperature | Nothing | U016487
(Combination meter assembly) |
||
| Meter
(Displays advice and warnings.) |
Combination meter assembly | Headlight ECU sub-assembly LH | Turns off. | Nothing | U018287
(Combination meter assembly) |
| Blind spot monitor sensor RH (B) | Turns off. | Nothing | U023387
(Combination meter assembly) |
||
| Forward recognition camera | Nothing | ·
LDA, LKA and LTC telltale lights illuminate ·
Malfunction displayed on multi-information display |
U023A87
(Combination meter assembly) |
||
| EV control ECU | HV system indicator does not operate | Nothing | U029387
(Combination meter assembly) |
||
| Certification ECU (smart key ECU assembly) | The last value is maintained | Nothing | U032487
(Combination meter assembly) |
||
| Clearance warning ECU assembly | Nothing | Clearance sonar off light illuminates | U111087
(Combination meter assembly) |
||
| Meter mirror sub-assembly | The last value is maintained | Nothing | Nothing | ||
| DCM (telematics transceiver) | The last value is maintained | Nothing | Nothing | ||
| Passenger Information Transmission
(Transmits passenger information, etc., to the airbag ECU assembly.) |
Airbag ECU assembly | Airbag ECU assembly | Nothing | ABG warning light illuminates | Nothing |
| P Control
(Changes the shift position to P or changes from P to any other position (transmission parking lock mechanism is locked/unlocked auto P).) |
Shift control ECU | Main body ECU (multiplex network body ECU) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
U014000
(Shift control ECU) |
| Shift Control
(Determines the request range based on shift lever sensor input, and sends shift information to the EV control ECU.) |
Shift control ECU | Main body ECU (multiplex network body ECU) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
U014000
(Shift control ECU) |
| Shift Position Display (Meter/Indicator)
(Displays the current shift position and operation pattern on the combination meter assembly.) |
Shift control ECU | Main body ECU (multiplex network body ECU) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
U014000
(Shift control ECU) |
| P Control
(Changes the shift position to P or changes from P to any other position (transmission parking lock mechanism is locked/unlocked auto P).) |
Shift control ECU | Certification ECU (smart key ECU assembly) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
U110700
(Shift control ECU) |
| Shift Control
(Determines the request range based on shift lever sensor input, and sends shift information to the EFI/HV-ECU.) |
Shift control ECU | Certification ECU (smart key ECU assembly) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
U110700
(Shift control ECU) |
| Shift Position Display (Meter/Indicator)
(Displays the current shift position and operation pattern on the meter.) |
Shift control ECU | Certification ECU (smart key ECU assembly) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
U110700
(Shift control ECU) |
| P Control
(Changes the shift position to P or changes from P to any other position (transmission parking lock mechanism is locked/unlocked auto P).) |
Shift control ECU | Combination meter assembly | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
U010387
(Shift control ECU) |
| Shift Control
(Determines the request range based on shift lever sensor input, and sends shift information to the EFI/HV-ECU.) |
Shift control ECU | Combination meter assembly | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
U010387
(Shift control ECU) |
| Shift Position Display (Meter/Indicator)
(Displays the current shift position and operation pattern on the combination meter assembly.) |
Shift control ECU | Combination meter assembly | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
U010387
(Shift control ECU) |
| P Control
(Changes the shift position to P or changes from P to any other position (transmission parking lock mechanism is locked/unlocked auto P).) |
Shift control ECU | Brake actuator assembly (No. 2 skid control ECU) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. ·
Stop the vehicle in a safe location and press P switch |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. ·
Stop the vehicle in a safe location and press P switch |
U117000
(Shift control ECU) |
| Shift Control
(Determines the request range based on shift lever sensor input, and sends shift information to the EV control ECU.) |
Shift control ECU | Brake actuator assembly (No. 2 skid control ECU) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. ·
Stop the vehicle in a safe location and press P switch |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. ·
Stop the vehicle in a safe location and press P switch |
U117000
(Shift control ECU) |
| Shift Position Display (Meter/Indicator)
(Displays the current shift position and operation pattern on the meter.) |
Shift control ECU | Brake actuator assembly (No. 2 skid control ECU) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. ·
Stop the vehicle in a safe location and press P switch |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. ·
Stop the vehicle in a safe location and press P switch |
U117000
(Shift control ECU) |
| P Control
(Changes the shift position to P or changes from P to any other position (transmission parking lock mechanism is locked/unlocked auto P).) |
Shift control ECU | Airbag ECU assembly | ·
P switching delay control is stopped ·
Stops the control to prevent shift position change from P on incline when the ignition switch is ON or READY off |
Nothing | Nothing |
| P Control
(Changes the shift position to P or changes from P to any other position (transmission parking lock mechanism is locked/unlocked auto P).) |
Shift control ECU | Central Gateway ECU (Network Gateway ECU) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
The following message is displayed on the multi-information display | U010387
(Shift control ECU) |
| Shift Control
(Determines the request range based on shift lever sensor input, and sends shift information to the EFI/HV-ECU.) |
Shift control ECU | Central Gateway ECU (Network Gateway ECU) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
U010387
(Shift control ECU) |
| Shift Position Display (Meter/Indicator)
(Displays the current shift position and operation pattern on the meter.) |
Shift control ECU | Central Gateway ECU (Network Gateway ECU) | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Apply parking brake and check owner's manual while parked |
U010387
(Shift control ECU) |
| P Control
(Changes the shift position to P or changes from P to any other position (transmission parking lock mechanism is locked/unlocked auto P).) |
Shift control ECU | EV control ECU | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
U029300
(Shift control ECU) |
| Shift Control
(Determines the request range based on shift lever sensor input, and sends shift information to the EFI/HV-ECU.) |
Shift control ECU | EV control ECU | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
U029300
(Shift control ECU) |
| Shift Position Display (Meter/Indicator)
(Displays the current shift position and operation pattern on the meter.) |
Shift control ECU | EV control ECU | The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
The following message is displayed on the multi-information display
·
Shift system malfunction ·
Check owner's manual. |
U029300
(Shift control ECU) |
| P Control
(Changes the shift position to P or changes from P to any other position (transmission parking lock mechanism is locked/unlocked auto P).) |
Shift control ECU | Clearance warning ECU assembly | ·
Communication stop is detected (DTC stored) ·
Communication stop is sent to the clearance warning ECU assembly |
Notified by multi-information display, telltale and clearance sonar buzzer | U111087
(Shift control ECU) |
| Shift Control
(Determines the request range based on shift lever sensor input, and sends shift information to the EFI/HV-ECU.) |
Shift control ECU | Clearance warning ECU assembly | ·
Communication stop is detected (DTC stored) ·
Communication stop is sent to the clearance warning ECU assembly |
Notified by multi-information display, telltale and clearance sonar buzzer | U111087
(Shift control ECU) |
| Shift Position Display (Meter/Indicator)
(Displays the current shift position and operation pattern on the meter.) |
Shift control ECU | Clearance warning ECU assembly | ·
Communication stop is detected (DTC stored) ·
Communication stop is sent to the clearance warning ECU assembly |
Notified by multi-information display, telltale and clearance sonar buzzer | U111087
(Shift control ECU) |
| Active Sound Control System
(Obtains vehicle information signals and outputs the engine sound.) |
Stereo component equalizer assembly | Stereo component equalizer assembly | Sound output is stopped | Nothing | ·
U0125 ·
U0129 ·
U0142 ·
U0293 (Stereo component equalizer assembly) |
| Vehicle Proximity Notification Function
(The vehicle proximity notification system outputs a sound (speaker) based on the vehicle speed or other input signal, in order to provide a warning to pedestrians/bicycles when a quiet EV/HEV vehicle draws near.) |
Vehicle approaching speaker controller | Brake actuator assembly (No. 2 skid control ECU) | Control is performed with the volume set to the level that is used when the vehicle speed is 0 km/h and no frequency shift | Nothing | U0129
(Vehicle approaching speaker controller) |
| Main body ECU (multiplex network body ECU) | Control is continued using the last value | Nothing | U0140
(Vehicle approaching speaker controller) |
||
| EV control ECU | Sound playback is stopped | Nothing | U0293
(Vehicle approaching speaker controller) |
||
| ABS
(Prevents the wheels from locking during sudden stops.) |
Brake actuator assembly (No. 2 skid control ECU) | Nothing | ABS control is continued | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
Nothing |
| Brake Assist
(Estimates the driver's intentions based on the speed and force at which the brake pedal is depressed and assists the braking force.) |
Brake actuator assembly (No. 2 skid control ECU) | Airbag ECU assembly | Brake assist control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
U012587
(Brake actuator assembly [No. 2 skid control ECU]) |
| TRC/VSC/VDIM
(Suppresses vehicle instability, such as sliding sideways when cornering and wheel slippage when starting off.) |
Brake actuator assembly (No. 2 skid control ECU) | EV control ECU | TRC/VSC/VDIM control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
·
U029387 ·
U115087 (Brake actuator assembly [No. 2 skid control ECU]) |
| Airbag ECU assembly | TRC/VSC/VDIM control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
U012587
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| Steering sensor | TRC/VSC/VDIM control is stopped | ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks |
U012687
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| Hill-start Assist Control
(Maintains brake pressure for 2 seconds between depressing the brake pedal and depressing the accelerator pedal, when starting off on a hill.) |
Brake actuator assembly (No. 2 skid control ECU) | EV control ECU | Hill-start assist control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
·
U029387 ·
U115087 (Brake actuator assembly [No. 2 skid control ECU]) |
| Airbag ECU assembly | Hill-start assist control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
U012587
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| Steering sensor | Hill-start assist control is stopped | ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks |
U012687
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| Brake Hold
(Controls to maintain the brake oil pressure when the vehicle is stopped.) |
Brake actuator assembly (No. 2 skid control ECU) | EV control ECU | Brake hold control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
·
U029387 ·
U115087 (Brake actuator assembly [No. 2 skid control ECU]) |
| Airbag ECU assembly | Brake hold control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
U012587
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| Steering sensor | Brake hold control is stopped | ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks |
U012687
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| Secondary Collision Brake
(Avoids a secondary collision after a collision is detected.) |
Brake actuator assembly (No. 2 skid control ECU) | EV control ECU | Control is stopped. | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
·
U029387 ·
U115087 (Brake actuator assembly [No. 2 skid control ECU]) |
| Airbag ECU assembly | Control is stopped. | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
·
U012587 ·
U015187 (Brake actuator assembly [No. 2 skid control ECU]) |
||
| Coordinated Regeneration
(Performs regenerative brake coordinated control with the HV system.) |
Brake actuator assembly (No. 2 skid control ECU) | EV control ECU | Regenerative brake coordinated control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
·
U029387 ·
U115087 (Brake actuator assembly [No. 2 skid control ECU]) |
| Certification ECU (smart key ECU assembly) | Regenerative brake coordinated control is stopped | Brake warning light illuminates | U110787
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| Airbag ECU assembly | Regenerative brake coordinated control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
U012587
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| Brake booster assembly (No. 1 skid control ECU) | Regenerative brake coordinated control is stopped | Brake warning light illuminates | U025E87
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| TCS (Trailer Sway Control)
(Suppresses the swaying of the trailer when a trailer is being towed.) |
Brake actuator assembly (No. 2 skid control ECU) | Airbag ECU assembly | Trailer sway control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
U012587
(Brake actuator assembly [No. 2 skid control ECU]) |
| Steering sensor | Trailer sway control is stopped | ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks |
U012687
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| Shift Link
(Automatically operates the electric parking brake when the shift position is changed to P, and automatically releases the electric parking brake when the shift position is changed to D, N or R.) |
Brake actuator assembly (No. 2 skid control ECU) | EV control ECU | Shift-linked control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
U029387
(Brake actuator assembly [No. 2 skid control ECU]) |
| Drive Away Release
(Controls to release the parking brake when the accelerator pedal is depressed with the shift position in D or R.) |
Brake actuator assembly (No. 2 skid control ECU) | EV control ECU | Drive away release control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
U029387
(Brake actuator assembly [No. 2 skid control ECU]) |
| Airbag ECU assembly | Drive away release control is stopped | ·
ABS and brake assist warning light illuminates ·
Slip indicator light illuminates ·
Brake hold standby indicator light blinks ·
Brake warning light illuminates |
U012587
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| Main body ECU (multiplex network body ECU) | Drive away release control is stopped | MIL illuminates | U014087
(Brake actuator assembly [No. 2 skid control ECU]) |
||
| Eco Driving Indicator
(Displays the Eco drive indicator on the headup display according to the Eco zone display condition amount signal sent from the detection ECU.) |
Meter mirror sub-assembly | EV control ECU | Eco zone display condition amount: Displays the Eco display exception status (ECO OFF) | Nothing | U029387
(Meter mirror sub-assembly) |
| Dynamic Radar Cruise Control System
(Displays the radar preceding vehicle, set vehicle-to-vehicle distance and set vehicle speed on the headup display according to the radar cruise display signal sent from the detection ECU.) |
Meter mirror sub-assembly | EV control ECU | ACC display (preceding vehicle, interrupt, time between vehicles): Not displayed | Nothing | U029387
(Meter mirror sub-assembly) |
| Brake Override System
(Displays the operation status of the brake override system on the headup display according to the brake override system display signal sent from the detection ECU.) |
Meter mirror sub-assembly | EV control ECU | Not displayed | Nothing | U029387
(Meter mirror sub-assembly) |
| Drive-start Control System
(Displays the drive start control operation status on the headup display according to the drive start control display signal sent from the detection ECU.) |
Meter mirror sub-assembly | EV control ECU | Not displayed | Nothing | U029387
(Meter mirror sub-assembly) |
| Road Sign Assist System - Dynamic Radar Cruise Control System
(Displays a frame on the target sign on the headup display and an arrow next to the set vehicle speed according to the road sign assist - dynamic radar cruise control display signal sent from the detection ECU.) |
Meter mirror sub-assembly | EV control ECU | ·
RSA-ACC target sign box: Not displayed ·
RSA-ACC arrow: Not displayed |
Nothing | U029387
(Meter mirror sub-assembly) |
| Shift Display
(Displays the shift position on the headup display according to the shift position signal sent from the shift control ECU.) |
Meter mirror sub-assembly | Shift control ECU | ·
Shift position: Not displayed ·
Shift gear: Not displayed ·
GSI: Not displayed |
Nothing | U010387
(Meter mirror sub-assembly) |
| Destination Switching
(Switches the ambient temperature unit according to the destination.) |
Meter mirror sub-assembly | Main body ECU (multiplex network body ECU) | Control is performed using the last signal received | Nothing | U014287
(Meter mirror sub-assembly) |
| Seat Memory Link
(Stores and recalls the display position of the headup display according to the seat position signal sent from the main body ECU.) |
Meter mirror sub-assembly | Main body ECU (multiplex network body ECU) | Performs control as though there is no seat memory recall
(Continues to operate the motor and completes the position recall operation if communication loss is assumed during motor operation) |
Nothing | ·
U014087 ·
U014287 (Meter mirror sub-assembly) |
| Speedometer
(Displays the current vehicle speed on the headup display according to the current vehicle speed signal sent from the combination meter.) |
Meter mirror sub-assembly | Combination meter assembly | ·
Vehicle speed display value: 0 is displayed ·
Vehicle speed unit: Not displayed |
Nothing | U015587
(Meter mirror sub-assembly) |
| Master Caution
(Displays the master caution icon and message on the headup display according to the master caution display signal sent from the combination meter.) |
Meter mirror sub-assembly | Combination meter assembly | Not displayed | Nothing | U015587
(Meter mirror sub-assembly) |
| Information
(Hides the information icon and message on the headup display according to the information display signal sent from the combination meter.) |
Meter mirror sub-assembly | Combination meter assembly | Not displayed | Nothing | U015587
(Meter mirror sub-assembly) |
| Display Customization
(Switches whether content is displayed on the headup display in the customize setting on the multi-information display.) |
Meter mirror sub-assembly | Combination meter assembly | Performs control as though the customize switch is off | Nothing | U015587
(Meter mirror sub-assembly) |
| Language Link (Combination Meter Assembly)
(Switches the display language of the headup display (meter text) according to the language set in the combination meter assembly.) |
Meter mirror sub-assembly | Combination meter assembly | Control is performed using the last signal received | Nothing | U015587
(Meter mirror sub-assembly) |
| Brightness Adjustment
(Adjusts the display brightness of the headup display in the customize setting on the multi-information display.) |
Meter mirror sub-assembly | Combination meter assembly | ·
Brightness up/down: Control performed as though there is no input (maintains the last brightness condition) ·
Headlight illumination condition: Maintains the last valid state |
Nothing | U015587
(Meter mirror sub-assembly) |
| Display Position Adjustment
(Adjusts the display position of the headup display in the customize setting on the multi-information display.) |
Meter mirror sub-assembly | Combination meter assembly | Position up/down: Control performed as though there is no input (maintains the last position condition) | Nothing | U015587
(Meter mirror sub-assembly) |
| Correcting Direction
(Turns the headup display into the desired direction using the customize setting on the multi-information display.) |
Meter mirror sub-assembly | Combination meter assembly | Display rotation: Control performed as though there is no input (does not rotate) | Nothing | U015587
(Meter mirror sub-assembly) |
| Language Link (Multi-media)
(Switches the display language of the headup display according to the language set in the radio receiver (multi-media linked language).) |
Meter mirror sub-assembly | ·
Radio receiver assembly ·
Radio and display receiver assembly |
Control is performed using the last signal received | Nothing | U016387
(Meter mirror sub-assembly) |
| Ambient Temperature/Road Surface Ice Display
(Displays the ambient temperature and surface ice mark on the headup display according to the ambient temperature signal sent from the air conditioning amplifier.) |
Meter mirror sub-assembly | Air conditioning amplifier assembly | Ambient temperature: Error value is displayed | Nothing | U016487
(Meter mirror sub-assembly) |
| Pre-collission Safety System
(Displays "BRAKE!" on the headup display according to the pre-collission safety system warning display signal sent from the millimeter wave radar sensor.) |
Meter mirror sub-assembly | Millimeter wave radar sensor assembly | PCS warning: Not displayed | Nothing | U023587
(Meter mirror sub-assembly) |
| Pre-collission Safety System
(Displays "BRAKE!" on the headup display according to the pre-collission safety system warning display signal sent from the forward recognition camera.) |
Meter mirror sub-assembly | Forward recognition camera | PCS warning: Not displayed | Nothing | U023A87
(Meter mirror sub-assembly) |
| Lane Departure Alert System/Lane Keeping Assist System (GSP)
(Displays the left/right white line mark, steering mark and rest alert marks on the headup display according to the lane departure alert system display signal sent from the forward recognition camera.) |
Meter mirror sub-assembly | Forward recognition camera | LDA display (white lines, steering mark and rest encouragement mark): Not displayed | Nothing | U023A87
(Meter mirror sub-assembly) |
| Road Sign Assist System
(Displays traffic signs (speed limits, etc.) according to the traffic sign signal sent from the forward recognition camera.) |
Meter mirror sub-assembly | Forward recognition camera | Traffic sign: Not displayed | Nothing | U023A87
(Meter mirror sub-assembly) |
| Lane Trace Control
(Displays the advanced driving support display matched with the shape of the actual curve (lane departure alert white lines, lane trace control self-confident wall, radar cruise preceding vehicle, set vehicle distance, etc.) according to the curve number s |
Meter mirror sub-assembly | Forward recognition camera | Walls/white lines: Not displayed | Nothing | U023A87
(Meter mirror sub-assembly) |
| HV Indicator
(Displays the HV indicator on the headup display according to the HV indicator signal sent from the EV control ECU.) |
Meter mirror sub-assembly | EV control ECU | Eco zone display condition amount: Input is controlled as the default setting | Nothing | U029387
(Meter mirror sub-assembly) |
| Pre-collission Safety System
(Displays "BRAKE!" on the headup display according to the pre-collission safety system warning display signal sent from the forward recognition camera.) |
Meter mirror sub-assembly | Forward recognition camera | PCS warning: Not displayed | Nothing | U110487
(Meter mirror sub-assembly) |
| Pedestrian Warning Alert
(Displays pedestrian warning alerts according to the target direction signal sent from the forward recognition camera.) |
Meter mirror sub-assembly | Forward recognition camera | Pedestrian warning alert: Not displayed | Nothing | U110487
(Meter mirror sub-assembly) |
| Front Cross Traffic Alert System
(Displays front cross traffic alerts according to the cross traffic alert detection signal sent from the forward recognition camera.) |
Meter mirror sub-assembly | Forward recognition camera | FCTA: Not displayed | Nothing | U110487
(Meter mirror sub-assembly) |
| Lane Trace Control System
(Displays the advanced driving support display matched with the shape of the actual curve (lane departure alert white lines, lane trace control self-confident wall, radar cruise preceding vehicle, set vehicle distance, etc.) according to the curve number s |
Meter mirror sub-assembly | Forward recognition camera | Walls/white lines: Not displayed | Nothing | U110487
(Meter mirror sub-assembly) |
| Lane Control System
(Displays the operation status of the lane control system on the headup display according to the lane control system planned course signal sent from the forward recognition camera.) |
Meter mirror sub-assembly | Forward recognition camera | Not displayed | Nothing | U110487
(Meter mirror sub-assembly) |
| Vehicle Stop Support System
(Displays the operation status of the stop support system on the headup display according to the vehicle stop support system display request signal sent from the forward recognition camera.) |
Meter mirror sub-assembly | Forward recognition camera | Not displayed | Nothing | U110487
(Meter mirror sub-assembly) |
| Preceding Vehicle Start Notification System
(Displays LVN "Preceding Vehicle Start" on the headup display according to the LVN display signal sent from the forward recognition camera.) |
Meter mirror sub-assembly | Forward recognition camera | Not displayed | Nothing | U110487
(Meter mirror sub-assembly) |
| Clearance Sonar System
(Displays the clearance sonar detection status on the headup display according to the clearance sonar display signal sent from the clearance warning ECU.) |
Meter mirror sub-assembly | Clearance warning ECU assembly | Clearance sonar (the vehicle/detection bar/frame): Not displayed | Nothing | U111087
(Meter mirror sub-assembly) |
| Intelligent Clearance Sonar System
(Displays the operation status of the intelligent clearance sonar system on the headup display according to the intelligent clearance sonar system display signal sent from the clearance warning ECU.) |
Meter mirror sub-assembly | Clearance warning ECU assembly | Not displayed | Nothing | U111087
(Meter mirror sub-assembly) |
| Smart Entry Function
(Stops smart entry when the power source is on, stops smart entry when the door is open, and performs smart unlock, smart PSD (left side) open, smart PSD (right side) open, smart back door unlatch and back door kick sensor unlock.) |
Certification ECU (smart key ECU assembly) | ·
Main body ECU (multiplex network body ECU) ·
Rear multiplex network door ECU RH ·
Rear multiplex network door ECU LH |
Nothing | Nothing | ·
U0140 ·
U0201 ·
U0202 (Certification ECU [smart key ECU assembly]) |
| Smart Lock Function
(Stops smart lock when the power source is on, stops smart lock when the door is open, stops smart lock when driving, and performs smart lock, power back door close & lock and power back door kick sensor close.) |
Certification ECU (smart key ECU assembly) | ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly ·
Rear multiplex network door ECU RH ·
Rear multiplex network door ECU LH |
Nothing | Nothing | ·
U0140 ·
U0155 ·
U0201 ·
U0202 (Certification ECU [smart key ECU assembly]) |
| Smart Trunk Open Function
(Performs smart trunk opening and trunk kick sensor opening.) |
Certification ECU (smart key ECU assembly) | Main body ECU (multiplex network body ECU) | Nothing | Nothing | U0140
(Certification ECU [smart key ECU assembly]) |
| Key Lock-in Prevention Function for Cabin
(Performs key lock-in prevention for cabin.) |
Certification ECU (smart key ECU assembly) | Main body ECU (multiplex network body ECU) | Nothing | Nothing | U0140
(Certification ECU [smart key ECU assembly]) |
| Smart Warning/Advice Display Function
(Provides smart key portable device low battery warnings, emergency operation displays, EV system start operation notifications, passenger leaves with key warnings, EV system start without smart vehicle interior key warnings , smart key lock-in prevention |
Certification ECU (smart key ECU assembly) | Combination meter assembly | Nothing | Nothing | U0155
(Certification ECU [smart key ECU assembly]) |
| Steering Function
(Locks/unlocks the steering lock.) |
Certification ECU (smart key ECU assembly) | ·
Main body ECU (multiplex network body ECU) ·
Brake actuator assembly (No. 2 skid control ECU) |
Nothing | Nothing | ·
U0140 ·
U0129 (Certification ECU [smart key ECU assembly]) |
| Power Switch Lettering Illumination Function
(Operates the power switch lettering illumination in conjunction with illumination of the dome light, whether the door is opened/closed, etc.) |
Certification ECU (smart key ECU assembly) | ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly |
Nothing | Nothing | ·
U0140 ·
U0155 (Certification ECU [smart key ECU assembly]) |
| Memory Function
(Performs memory key registration and recall.) |
Certification ECU (smart key ECU assembly) | Main body ECU (multiplex network body ECU) | Nothing | Nothing | U0140
(Certification ECU [smart key ECU assembly]) |
| Key Registration Function
(Creates/adds/deletes a key, deletes all keys and perform ECU code registration.) |
Certification ECU (smart key ECU assembly) | ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly |
Nothing | Nothing | ·
U0140 ·
U0155 (Certification ECU [smart key ECU assembly]) |
| Wireless Function
(Locks/unlocks the vehicle, etc. via remote operation.) |
Certification ECU (smart key ECU assembly) | Main body ECU (multiplex network body ECU) | Nothing | Nothing | U0140
(Certification ECU [smart key ECU assembly]) |
| Headlight On/Off Control
(Turns the low beams, high beams, daytime running lights and clearance lights of/off.) |
Main body ECU (multiplex network body ECU) | ·
EV control ECU ·
Headlight ECU sub-assembly LH ·
Headlight ECU sub-assembly RH |
Nothing | ·
Nothing ·
Nothing for this function (notification may be provided from another function) |
U029387
(Main body ECU [multiplex network body ECU]) |
| The low beams are forced on if there is a malfunction in the low beams | Headlight system malfunction (telltale, or message displayed on multi-information display) | U014087
(Main body ECU [multiplex network body ECU]) |
|||
| Nothing | Nothing | ·
U014087 ·
U114F87 (Main body ECU [multiplex network body ECU]) |
|||
| Nothing | Nothing (not possible as headlight ECU sub-assembly LH communication is stopped) | U024187
(Main body ECU [multiplex network body ECU]) |
|||
| Nothing | Nothing for this function (notification may be provided from another function) | U024287
(Main body ECU [multiplex network body ECU]) |
|||
| Cornering Light (CL) Control
(Turns the cornering light on/off based on the wheel speed, turn, steering angle and shift position data.) |
Headlight ECU sub-assembly LH | ·
Main body ECU (multiplex network body ECU) ·
EV control ECU ·
Headlight ECU sub-assembly RH ·
Steering sensor ·
Rack and pinion power steering gear assembly ·
Brake actuator assembly (No. 2 skid control ECU) |
Nothing | ·
Nothing ·
Nothing for this function (notification may be provided from another function) |
U029387
(Headlight ECU sub-assembly LH) |
| Cornering light control is stopped | Nothing for this function (notification may be provided from another function) | U010187
(Headlight ECU sub-assembly LH) |
|||
| Cornering Light (CL) Control
(Performs headlight cleaner on/off control.) |
Headlight ECU sub-assembly LH | ·
Main body ECU (multiplex network body ECU) ·
EV control ECU ·
Headlight ECU sub-assembly RH ·
Steering sensor ·
Rack and pinion power steering gear assembly ·
Brake actuator assembly (No. 2 skid control ECU) |
Cornering light control is stopped | Nothing for this function (notification may be provided from another function) | ·
U013187 ·
U012987 (Headlight ECU sub-assembly LH) |
·
Nothing ·
Cornering light control is stopped |
·
Nothing ·
Nothing for this function (notification may be provided from another function) |
U014087
(Headlight ECU sub-assembly LH) |
|||
| Cornering light control for the right headlight is stopped | Nothing (not possible as headlight ECU sub-assembly LH communication is stopped) | U024187
(Headlight ECU sub-assembly LH) |
|||
| Cornering light control is stopped | Nothing for this function (notification may be provided from another function) | U024287
(Headlight ECU sub-assembly LH) |
|||
| Headlight Cleaner (HLC) Control
(Performs headlight cleaner on/off control.) |
Headlight ECU sub-assembly RH | ·
Main body ECU (multiplex network body ECU) ·
EV control ECU ·
Steering sensor ·
Headlight ECU sub-assembly LH |
Nothing | ·
Nothing ·
Nothing for this function (notification may be provided from another function) |
U029387
[Headlight ECU sub-assembly RH] |
| Headlight cleaner control is stopped | Nothing | U012687
[Headlight ECU sub-assembly RH] |
|||
·
Nothing ·
Headlight cleaner control is stopped |
·
Nothing ·
Nothing for this function (notification may be provided from another function) |
U014087
[Headlight ECU sub-assembly RH] |
|||
| Nothing | Nothing (not possible as headlight ECU sub-assembly LH communication is stopped) | U024187
[Headlight ECU sub-assembly RH] |
|||
| Headlight cleaner control is stopped | Nothing for this function (notification may be provided from another function) | U024287
[Headlight ECU sub-assembly RH] |
|||
| Static Leveling (SHL) Control
(Adjust the vertical beam axis direction of the headlights according to the pitch angle calculated using the wheel speeds and vehicle height sensor value.) |
Headlight ECU sub-assembly LH | ·
Main body ECU (multiplex network body ECU) ·
EV control ECU ·
Headlight ECU sub-assembly RH ·
Combination meter assembly ·
Brake actuator assembly (No. 2 skid control ECU) |
Nothing | ·
Nothing ·
Nothing for this function (notification may be provided from another function) |
U029387
(Headlight ECU sub-assembly LH) |
| Static leveling control is stopped | Headlight system malfunction (telltale, or message displayed on multi-information display) | U012987
(Headlight ECU sub-assembly LH) |
|||
| Nothing | ·
Nothing ·
Nothing for this function (notification may be provided from another function) |
U014087
(Headlight ECU sub-assembly LH) |
|||
| Nothing | Nothing | U015587
(Headlight ECU sub-assembly LH) |
|||
| Nothing | Nothing (not possible as headlight ECU sub-assembly LH communication is stopped) | U024187
(Headlight ECU sub-assembly LH) |
|||
| Nothing | Headlight system malfunction (telltale, or message displayed on multi-information display) | U024287
(Headlight ECU sub-assembly LH) |
|||
| Dynamic Leveling (DHL) Control
(Adjust the vertical beam axis direction of the headlights according to the pitch angle calculated using the wheel speeds and vehicle height sensor value.) |
Headlight ECU sub-assembly LH | ·
Main body ECU (multiplex network body ECU) ·
EV control ECU ·
Headlight ECU sub-assembly RH ·
Combination meter assembly ·
Brake actuator assembly (No. 2 skid control ECU) |
Nothing | ·
Nothing ·
Headlight system malfunction (telltale, or message displayed on multi-information display) |
U029387
(Headlight ECU sub-assembly LH) |
| Dynamic leveling control with the vehicle speed at 0 km/h is performed | Headlight system malfunction (telltale, or message displayed on multi-information display) | U012987
(Headlight ECU sub-assembly LH) |
|||
| Nothing | ·
Nothing ·
Nothing for this function (notification may be provided from another function) |
U014087
(Headlight ECU sub-assembly LH) |
|||
| Nothing | Nothing | U015587
(Headlight ECU sub-assembly LH) |
|||
| Nothing | Nothing (not possible as headlight ECU sub-assembly LH communication is stopped) | U024187
(Headlight ECU sub-assembly LH) |
|||
| Nothing | Headlight system malfunction (telltale, or message displayed on multi-information display) | U024287
(Headlight ECU sub-assembly LH) |
|||
| AFS Control
(Performs headlight beam axis control in the swiveling direction while the vehicle is turning.) |
Headlight ECU sub-assembly LH | ·
Main body ECU (multiplex network body ECU) ·
EV control ECU ·
Headlight ECU sub-assembly RH ·
Combination meter assembly ·
Steering sensor ·
Rack and pinion power steering gear assembly ·
Brake actuator assembly (No. 2 skid control ECU) |
Nothing | ·
Nothing ·
Headlight system malfunction (telltale, or message displayed on multi-information display) |
U029387
(Headlight ECU sub-assembly LH) |
| AFS control is stopped | Headlight system malfunction (telltale, or message displayed on multi-information display) | ·
U010187 ·
U013187 ·
U012987 (Headlight ECU sub-assembly LH) |
|||
| AFS control is stopped | ·
Nothing ·
Headlight system malfunction (telltale, or message displayed on multi-information display) |
U014087
(Headlight ECU sub-assembly LH) |
|||
| Nothing | Nothing | U015587
(Headlight ECU sub-assembly LH) |
|||
| AFS control is stopped | Nothing (not possible as headlight ECU sub-assembly LH communication is stopped) | U024187
(Headlight ECU sub-assembly LH) |
|||
| AFS control is stopped | Headlight system malfunction (telltale, or message displayed on multi-information display) | U024287
(Headlight ECU sub-assembly LH) |
|||
| AHS Control
(Automatically turns Hi on/off, illuminates the light sources of the cornering lights at low speed (when starting off or stopped), performs upward control of the headlight beam axis at high speed, and performs cut-off line preceding vehicle following.) |
Headlight ECU sub-assembly LH | ·
Main body ECU (multiplex network body ECU) ·
EV control ECU ·
Headlight ECU sub-assembly RH ·
Combination meter assembly ·
Rack and pinion power steering gear assembly ·
Brake actuator assembly (No. 2 skid control ECU) |
Nothing | ·
Nothing ·
Headlight system malfunction (telltale, or message displayed on multi-information display) |
U029387
(Headlight ECU sub-assembly LH) |
| AHS control is stopped | Headlight system malfunction (telltale, or message displayed on multi-information display) | ·
U010187 ·
U013187 ·
U012987 (Headlight ECU sub-assembly LH) |
|||
| AHS control is stopped | Headlight system malfunction (telltale, or message displayed on multi-information display) | U014087
(Headlight ECU sub-assembly LH) |
|||
| Nothing | Nothing | ·
U014087 ·
U015587 (Headlight ECU sub-assembly LH) |
|||
| AHS control rain mode is stopped | Headlight system malfunction (telltale, or message displayed on multi-information display) | U014087
(Headlight ECU sub-assembly LH) |
|||
| Nothing | Nothing (not possible as headlight ECU sub-assembly LH communication is stopped) | U024187
(Headlight ECU sub-assembly LH) |
|||
| AHS control is stopped | Headlight system malfunction (telltale, or message displayed on multi-information display) | U024287
(Headlight ECU sub-assembly LH) |
|||
| Multi-weather Light (MWL) Control
(Increases illumination toward the front of the vehicle during bad weather (such as fog).) |
Headlight ECU sub-assembly LH | ·
Main body ECU (multiplex network body ECU) ·
EV control ECU ·
Headlight ECU sub-assembly RH ·
Combination meter assembly ·
Steering sensor ·
Brake actuator assembly (No. 2 skid control ECU) |
Nothing | ·
Nothing for this function (notification may be provided from another function) ·
Headlight system malfunction (telltale, or message displayed on multi-information display) |
U029387
(Headlight ECU sub-assembly LH) |
| Multi-weather light control is stopped | Headlight system malfunction (telltale, or message displayed on multi-information display) | U010187
(Headlight ECU sub-assembly LH) |
|||
| Nothing | Nothing | ·
U012687 ·
U015587 (Headlight ECU sub-assembly LH) |
|||
| Multi-weather light control is stopped | Headlight system malfunction (telltale, or message displayed on multi-information display) | U012987
(Headlight ECU sub-assembly LH) |
|||
·
Multi-weather light control is stopped ·
Nothing |
·
Headlight system malfunction (telltale, or message displayed on multi-information display) ·
Nothing |
U014087
(Headlight ECU sub-assembly LH) |
|||
| Nothing | Nothing (not possible as headlight ECU sub-assembly LH communication is stopped) | U024187
(Headlight ECU sub-assembly LH) |
|||
| Multi-weather light control is stopped | Headlight system malfunction (telltale, or message displayed on multi-information display) | U024287
(Headlight ECU sub-assembly LH) |
|||
| Front Collision Detection Judgment
(Front collision detection judgment) |
Occupant detection ECU | Airbag ECU assembly | Only sensors are used to judge collision detection | Nothing | Nothing |
| Passenger Judgment
(Passenger judgment) |
Occupant detection ECU | Brake actuator assembly (No. 2 skid control ECU) | A malfunction is sent to the airbag ECU assembly | ABG warning light illuminates | U0129
(Occupant detection ECU) |
| Airbag ECU assembly | A malfunction is sent to the airbag ECU assembly | ABG warning light illuminates | U0125
(Occupant detection ECU) |