Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > FREEZE FRAME DATA

for Preparation Click here



DESCRIPTION
  1. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

  2. A103809E24
    Techstream displays freeze frame data recorded at five different points: 1) 3 times before the DTC is set, 2) once when the DTC is set, and 3) once after the DTC is set. The data can be used to simulate the vehicle's condition around the time of the malfunction. The data may be helpful in determining the cause of a malfunction. It may also be helpful in determining whether a DTC is being caused by a temporary malfunction.
  1. The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using Techstream, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.

LIST OF FREEZE FRAME DATA

LABEL
(Techstream Display)
Measurement Item/Range
Diagnostic Note
Injector (Port)
Injection period of No. 1 cylinder
-
IGN Advance
Ignition advance
-
Calculate Load
Calculate load
Calculated load by ECM (Included in HV Control ECU)
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If value is approximately 0.0 g/s:
  1. Mass air flow meter power source circuit open or shorted
  1. VG circuit open or short
If value is 160.0 g/s or more:
  1. E2G circuit open
Engine Speed
Engine speed
-
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Coolant Temp
Engine coolant temperature
If value is -40°C, sensor circuit open
If value is 140°C, sensor circuit shorted
Intake Air
Intake air temperature
If value is -40°C, sensor circuit open
If value is 140°C, sensor circuit shorted
Air-Fuel Ratio
Air-fuel ratio
-
Ambient Temperature
Ambient temperature
-
Purge Density Learn Value
Learning value of purge density
-
Evap Purge Flow
Purge flow
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Knock Correct Learn Value
Correction learning value of knocking
-
Knock Feedback Value
Feedback value of knocking
-
Electromagnetic Clutch
Electromagnetic clutch
-
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting idle
-
Throttle Fully Close Learn
Throttle valve fully closed (learned value)
-
Fail Safe Drive
Whether or not fail safe function executed
-
Fail Safe Drive (Main CPU)
Whether or not fail safe function executed
-
ST1
Brake pedal signal
-
System Guard
System guard
-
Open Side Malfunction
Open side malfunction
-
Throttle Idle Position
Whether or not throttle position sensor detecting idle
-
Throttle Require Position
Throttle requirement position
-
Throttle Sensor Position
Throttle sensor positioning
Read value with power switch ON (IG) (Do not start engine)
Throttle Sensor Position #2
Throttle sensor positioning #2
-
Throttle Position No.1
Throttle position sensor No. 1 output voltage
Read value with power switch ON (IG) (Do not start engine)
Throttle Position No.2
Throttle position sensor No. 2 output voltage
Read value with power switch ON (IG) (Do not start engine)
Throttle Position Command
Throttle position command value
Read value with power switch ON (IG) (Do not start engine)
Throttle Sens Open Pos #1
Throttle position sensor position No. 1
-
Throttle Sens Open Pos #2
Throttle position sensor position No. 2
-
Throttle Sens Open #1(AD)
Throttle position sensor No. 1 output voltage (AD)
Read value with power switch ON (IG) (Do not start engine)
Throttle Motor
Throttle motor
-
Throttle Motor Current
Throttle actuator current
-
Throttle Motor DUTY
Throttle actuator
-
Throttle Motor Duty (Open)
Throttle actuator duty ratio (open)
-
Throttle Motor Duty (Close)
Throttle actuator duty ratio (closed)
-
O2S B1 S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
AFS B1 S1
A/F sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
Total FT #1
Total fuel trim
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #1
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value
Fuel System Status (Bank1)
Fuel system status (Bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  1. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
  1. OL FAULT: Open loop due to detected system fault
  1. CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control, malfunctioning
Fuel System Status (Bank2)
Fuel system status (Bank 2)
  1. OL (Open Loop ): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  1. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
  1. OL FAULT: Open loop due to detected system fault
  1. CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control, malfunctioning
Catalyst Temp (B1 S1)
Catalyst temperature
-
Catalyst Temp (B1 S2)
Catalyst temperature
-
Sub O2S Impedance B1S2
HO2 sensor impedance (Bank 1 Sensor 2)
-
Initial Engine Coolant Temp
Initial engine coolant temperature
-
Initial Intake Air Temp
Initial intake air temperature
-
Injection Volum (Cylinder1)
Injection volume
-
Closed Throttle Position SW
Closed throttle position switch
-
Engine Oil Pressure SW
Engine oil pressure switch signal
Always ON while engine is running
ETCS Actuator Power
Whether or not electric throttle control system power input
-
+BM Voltage
+BM voltage
-
Battery Voltage
Battery voltage
-
Actuator Power Supply
Actuator power supply
-
Atmosphere Pressure
Atmospheric pressure
-
EVAP Purge VSV
EVAP purge VSV
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
VVT Control Status (Bank1)
VVT control status (bank 1)
-
Vacuum Pump
Vacuum pump
ON: Operate
EVAP System Vent Valve
EVAP system vent valve
ON: Close
Electric Fan Motor
Electric fan motor
ON: Operate
Tank Bypass VSV
Tank bypass VSV
-
TC and TE1
TC and TE1 terminals of DLC3
-
VVT Aim Angle (Bank1)
VVT aim angle (bank1)
-
VVT Change Angle (Bank1)
VVT change angle (bank 1)
-
VVT OCV Duty (Bank1)
VVT OCV operation duty (bank 1)
-
Idle Fuel Cut
Idle fuel cut
ON: when throttle valve fully closed and engine speed over 1,500 rpm
FC TAU
FC TAU
Fuel cut being performed under very light load to prevent incomplete engine combustion
Ignition
Ignition
-
Cylinder #1 Misfire Count
Cylinder #1 misfire rate
Displayed only during idling
Cylinder #2 Misfire Count
Cylinder #2 misfire rate
Displayed only during idling
Cylinder #3 Misfire Count
Cylinder #3 misfire rate
Displayed only during idling
Cylinder #4 Misfire Count
Cylinder #4 misfire rate
Displayed only during idling
All Cylinders Misfire Count
All cylinder misfire rate
Displayed only during idling
Misfire RPM
Misfire RPM
-
Misfire Load
Misfired load
-
Misfire Margin
Misfire monitoring
-
Engine Run Time
Accumulated engine running time
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleard DTC
Warm-up cycle after DTC cleared
-
Requested Engine Torque
Requested engine torque
-
HV Target Engine Speed
HV target engine speed
-
Actual Engine Torque
Actual engine torque
-
Estimated Engine Torque
Estimated engine torque
-
Engine Run Time
Engine run time
-
Request Engine Run Time
Request engine run time
-
Judge Time Engine Ignition
Judge time engine ignition
-
Judge Time Engine Output
Judge time engine output
-
Estimated Intake Port Temp
Estimated intake port temperature
-
Fuel Level
Fuel level
-
ISC Learning
ISC learning
-
F/C for Engine Stop Req
Fuel cut for engine stop request
-
Engine Independent
Engine independent operation
-
Racing Operation
Racing operation
-
Request Warm-up
Request warm-up
-
Engine Independent Control
Engine independent control
-
Tank Outlet Water Temp
Tank outlet water temperature
-
Water Flow Valve
Water flow valve
-
ISC Learning Value
ISC learning control
-
Direction Value 1
Direction value (water valve) (control side)
-
Direction Value 2
Direction value (water valve) (OBD side)
-