Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

OCCUPANT CLASSIFICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK OCCUPANT CLASSIFICATION ECU


  1. Measure the voltage of the connector.


    H100909E09


    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B (O4-1) - GND (O4-3)
    L - W-B
    +B power source
    Always
    10 to 14 V
    DIA (O4-2) - GND (O4-3)
    W - W-B
    Diagnosis (DLC3)
    Power switch ON (IG)
    Pulse generation
    GND (O4-3) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 V
    FSR- (O4-4) - GND (O4-3)
    Y-B - W-B
    Center airbag sensor communication line
    Always
    Below 1 V
    BGND (O4-5) - GND (O4-3)
    R - W-B
    Passenger side buckle switch ground line
    Always
    Below 1 V
    IG (O4-7) - GND (O4-3)
    B - W-B
    IG power source
    Power switch ON (IG)
    10 to 14 V
    FSR+ (O4-8) - FSR- (O4-4)
    Y - Y-B
    Center airbag sensor communication line
    Power switch ON (IG)
    Pulse generation
    BSW (O4-9) - BGND (O4-5)
    G - R
    Passenger side buckle switch line
    Buckle switch ON
    Buckle switch OFF
    Pulse generation
    SGD1 (O5-1) - GND (O4-3)
    G - W-B
    Front occupant classification sensor LH ground line
    Always
    Below 1 V
    SGD2 (O5-2) - GND (O4-3)
    O - W-B
    Front occupant classification sensor RH ground line
    Always
    Below 1 V
    SGD3 (O5-3) - GND (O4-3)
    W - W-B
    Rear occupant classification sensor LH ground line
    Always
    Below 1 V
    SGD4 (O5-4) - GND (O4-3)
    BR - W-B
    Rear occupant classification sensor RH ground line
    Always
    Below 1 V
    SVC1 (O5-11) - SGD1 (O5-1)
    R - G
    Front occupant classification sensor LH power supply line
    Power switch ON (IG), a load is applied to front occupant classification sensor LH
    4.5 to 5.1 V
    SVC2 (O5-12) - SGD2 (O5-2)
    W - O
    Front occupant classification sensor RH power supply line
    Power switch ON (IG), a load is applied to front occupant classification sensor RH
    4.5 to 5.1 V
    SVC3 (O5-5) - SGD3 (O5-3)
    GR - W
    Rear occupant classification sensor LH power supply line
    Power switch ON (IG), a load is applied to rear occupant classification sensor LH
    4.5 to 5.1 V
    SVC4 (O5-6) - SGD4 (O5-4)
    V - BR
    Rear occupant classification sensor RH power supply line
    Power switch ON (IG), a load is applied to rear occupant classification sensor RH
    4.5 to 5.1 V
    SIG1 (O5-7) - SGD1 (O5-1)
    SB - G
    Front occupant classification sensor LH signal line
    Power switch ON (IG), a load is applied to front occupant classification sensor LH
    0.2 to 4.7 V
    SIG2 (O5-8) - SGD2 (O5-2)
    L - O
    Front occupant classification sensor RH signal line
    Power switch ON (IG), a load is applied to front occupant classification sensor RH
    0.2 to 4.7 V
    SIG3 (O5-9) - SGD3 (O5-3)
    Y - W
    Rear occupant classification sensor LH signal line
    Power switch ON (IG), a load is applied to rear occupant classification sensor LH
    0.2 to 4.7 V
    SIG4 (O5-10) - SGD4 (O5-4)
    R - BR
    Rear occupant classification sensor RH signal line
    Power switch ON (IG), a load is applied to rear occupant classification sensor RH
    0.2 to 4.7 V