DTC B1782 Rear Occupant Classification Sensor LH Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1782 | When one of following conditions is met:
|
|

| 1.CHECK FOR DTC |
Turn the power switch ON (IG).
Clear the DTCs (Click here).
Turn the power switch OFF.
Turn the power switch ON (IG).
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the power switch OFF.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the rear occupant classification sensor LH.
|
| ||||
| OK | |
| 3.CHECK FRONT SEAT WIRE RH (TO B+) |
![]() |
Disconnect the connectors from the occupant classification ECU and the rear occupant classification sensor LH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the power switch ON (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| O5-3 (SGD3) - Body ground | Below 1 V |
| O5-5 (SVC3) - Body ground | Below 1 V |
| O5-9 (SIG3) - Body ground | Below 1 V |
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT WIRE RH (OPEN) |
![]() |
Turn the power switch OFF.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals O8-1 (SVC3) and O8-3 (SGD3), and connect terminals O8-2 (SIG3) and O8-3 (SGD3) of connector C.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| O5-5 (SVC3) - O5-3 (SGD3) | Below 1 Ω |
| O5-9 (SIG3) - O5-3 (SGD3) | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK FRONT SEAT WIRE RH (SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| O5-5 (SVC3) - O5-3 (SGD3) | 1 MΩ or higher |
| O5-9 (SIG3) - O5-3 (SGD3) | 1 MΩ or higher |
| O5-5 (SVC3) - O5-9 (SIG3) | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK FRONT SEAT WIRE RH (TO GROUND) |
![]() |
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| O5-3 (SGD3) - Body ground | 1 MΩ or higher |
| O5-5 (SVC3) - Body ground | 1 MΩ or higher |
| O5-9 (SIG3) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK FOR DTC |
Connect the connectors to the occupant classification ECU and the rear occupant classification sensor LH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the power switch ON (IG).
Clear the DTCs (Click here).
Turn the power switch OFF.
Turn the power switch ON (IG).
Check the DTCs (Click here).
|
| ||||
| NG | |
| 8.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the power switch OFF.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant classification ECU.
| NEXT | |
| 9.PERFORM ZERO POINT CALIBRATION |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Connect the Techstream to the DLC3.
Turn the power switch ON (IG).
Using the Techstream, perform the zero point calibration (Click here).
|
| ||||
| OK | |
| 10.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
|
| ||||
| OK | |
| 11.CHECK FOR DTC |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the power switch ON (IG).
Clear the DTCs (Click here).
Turn the power switch OFF.
Turn the power switch ON (IG).
Check the DTCs (Click here).
|
| ||||
| NG | |
| 12.REPLACE FRONT SEAT ASSEMBLY RH |
Turn the power switch OFF.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the front seat RH (Click here).
| NEXT | |
| 13.PERFORM ZERO POINT CALIBRATION |
Connect the cable to the negative (-) terminal battery, and wait for at least 2 seconds.
Connect the Techstream to the DLC3.
Turn the power switch ON (IG).
Using the Techstream, perform the zero point calibration (Click here).
| NEXT | |
| 14.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
| NEXT | ||
| ||