Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1783    Rear Occupant Classification Sensor RH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The rear occupant classification sensor RH circuit consists of the occupant classification ECU and the rear occupant classification sensor RH.
DTC B1783 is recorded when a malfunction is detected in the rear occupant classification sensor RH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1783
When one of following conditions is met:
  1. Occupant classification ECU detects line short signal, open signal, short to ground signal or short to B+ signal in the rear occupant classification sensor RH circuit for 2 seconds
  2. Rear occupant classification sensor RH malfunction
  3. Occupant classification ECU malfunction
  1. Front seat wire RH
  2. Front seat RH (Rear occupant classification sensor RH)
  3. Occupant classification ECU

WIRING DIAGRAM


C128670E08


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see the undersurface of the seat cushion.
  2. In the above case, hold the seat so that it does not tip over. Holding the seat for a long period of time may cause a problem, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK DTC
  1. Turn the power switch ON (IG).

  1. Clear the DTCs (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG).

  1. Check the DTCs (Click here).

    OK:
    DTC B1783 is not output.

    HINT:
    DTCs other than DTC B1783 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the rear occupant classification sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTOR
OK


3.CHECK FRONT SEAT WIRE RH (TO B+)


    C130827E04
  1. Disconnect the connectors from the occupant classification ECU and the rear occupant classification sensor RH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    O5-4 (SGD4) - Body ground
    Below 1 V
    O5-6 (SVC4) - Body ground
    Below 1 V
    O5-10 (SIG4) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE FRONT SEAT WIRE RH
OK


4.CHECK FRONT SEAT WIRE RH (OPEN)


    H100920E25
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals O9-1 (SVC4) and O9-3 (SGD4), and connect terminals O9-2 (SIG4) and O9-3 (SGD4) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting them.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    O5-6 (SVC4) - O5-4 (SGD4)
    Below 1 Ω
    O5-10 (SIG4) - O5-4 (SGD4)
    Below 1 Ω



NG
REPAIR OR REPLACE FRONT SEAT WIRE RH
OK


5.CHECK FRONT SEAT WIRE RH (SHORT)


    C130827E04
  1. Disconnect the service wire from connector C.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    O5-6 (SVC4) - O5-4 (SGD4)
    1 MΩ or higher
    O5-10 (SIG4) - O5-4 (SGD4)
    1 MΩ or higher
    O5-6 (SVC4) - O5-10 (SIG4)
    1 MΩ or higher



NG
REPAIR OR REPLACE FRONT SEAT WIRE RH
OK


6.CHECK FRONT SEAT WIRE RH (TO GROUND)


    C130827E04
  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    O5-4 (SGD4) - Body ground
    1 MΩ or higher
    O5-6 (SVC4) - Body ground
    1 MΩ or higher
    O5-10 (SIG4) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE FRONT SEAT WIRE RH
OK


7.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and the rear occupant classification sensor RH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Clear the DTCs (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG).

  1. Check the DTCs (Click here).

    OK:
    DTC B1783 is not output.

    HINT:
    DTCs other than DTC B1783 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


8.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU.

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


9.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 12
OK


10.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard values:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 12
OK


11.CHECK FOR DTC
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Clear the DTCs (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG).

  1. Check the DTCs (Click here).

    OK:
    DTC B1783 is not output.

    HINT:
    DTCs other than DTC B1783 may be output at this time, but they are not related to this check.



OK
END
NG


12.REPLACE FRONT SEAT ASSEMBLY RH
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat RH (Click here).


NEXT


13.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


14.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard values:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END