Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1788    Rear Occupant Classification Sensor RH Collision Detection

for Preparation Click here


DESCRIPTION

DTC B1788 is output when the occupant classification ECU receives a collision detection signal sent by the rear occupant classification sensor RH when an accident occurs.
DTC B1788 is also output when the front seat RH is subjected to a strong impact, even if an actual accident does not occur.
However, when the occupant classification ECU outputs a collision detection signal, even if the vehicle is not in a collision, DTC B1788 can be cleared by performing the zero point calibration and sensitivity check.
Therefore, when DTC B1788 is output, first perform the zero point calibration and sensitivity check.

DTC No.
DTC Detection Condition
Trouble Area
B1788
When one of following conditions is met:
  1. Front seat RH malfunction
  2. Occupant classification ECU malfunction
  3. Rear occupant classification sensor RH detects large load
  1. Occupant classification ECU
  2. Front seat RH (Rear occupant classification sensor RH)

WIRING DIAGRAM


C128670E12


INSPECTION PROCEDURE

1.PERFORM ZERO POINT CALIBRATION
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 4
OK


2.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 4
OK


3.CHECK FOR DTC
  1. Turn the power switch ON (IG).

  1. Clear the DTCs (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG).

  1. Check the DTCs (Click here).

    OK:
    DTC B1788 is not output.

    HINT:
    DTCs other than DTC B1788 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


4.REPLACE FRONT SEAT ASSEMBLY RH
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat RH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


5.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 8
OK


6.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 8
OK


7.CHECK FOR DTC
  1. Turn the power switch ON (IG).

  1. Clear the DTCs (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG).

  1. Check the DTCs (Click here).

    OK:
    DTC B1788 is not output.

    HINT:
    DTCs other than DTC B1788 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


8.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU.


NEXT


9.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


10.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END