Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1790    Center Airbag Sensor Assembly Communication Circuit Malfunction

for Preparation Click here


DESCRIPTION

The center airbag sensor communication circuit consists of the occupant classification ECU and the center airbag sensor.
DTC B1790 is recorded when a malfunction is detected in the center airbag sensor communication circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1790
When one of following conditions is met:
  1. Occupant classification ECU detects line short signal, open signal, short to ground signal or short circuit to B+ signal in the center airbag sensor communication circuit for 2 seconds
  2. Center airbag sensor malfunction
  3. Occupant classification ECU malfunction
  1. Floor wire No. 2
  2. Occupant classification ECU
  3. Center airbag sensor

WIRING DIAGRAM


C123527E03


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see the undersurface of the seat cushion.
  2. In the above case, hold the seat so that it does not tip over. Holding the seat for a long period of time may cause a problem, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK FOR DTC
  1. Turn the power switch ON (IG).

  1. Clear the DTCs (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG).

  1. Check the DTCs (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    DTCs other than DTC B1790 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the center airbag sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTOR
OK


3.CHECK FLOOR WIRE NO. 2 (TO B+)


    H100922E07
  1. Disconnect the connectors from the occupant classification ECU and the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    O4-8 (FSR+) - Body ground
    Below 1 V
    O4-4 (FSR-) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


4.CHECK FLOOR WIRE NO. 2 (OPEN)


    C130815E02
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals A19-16 (FSP+) and A19-24 (FSP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting them.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    O4-8 (FSR+) - O4-4 (FSR-)
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


5.CHECK FLOOR WIRE NO. 2 (SHORT)


    H100922E07
  1. Disconnect the service wire from connector B.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    O4-8 (FSR+) - O4-4 (FSR-)
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


6.CHECK FLOOR WIRE NO. 2 (TO GROUND)


    H100922E07
  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    O4-8 (FSR+) - Body ground
    1 MΩ or higher
    O4-4 (FSR-) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


7.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Clear the DTCs (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG).

  1. Check the DTCs (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    DTCs other than DTC B1790 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


8.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU.

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


9.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) terminal battery, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


10.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard values:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT


11.CHECK FOR DTC
  1. Turn the power switch ON (IG).

  1. Clear the DTCs (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG).

  1. Check the DTCs (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    DTCs other than DTC B1790 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END