Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

OCCUPANT CLASSIFICATION SYSTEM > Trouble in Passenger Airbag ON / OFF Indicator

for Preparation Click here


DESCRIPTION

The occupant classification system detects the front passenger seat condition and then indicates whether the front passenger airbag is activated or not through the passenger airbag ON / OFF indicator illumination.
The passenger airbag ON / OFF indicator illumination changes depending on the front passenger seat condition as shown in the table below.

Front Passenger Seat Condition
ON Indicator
OFF Indicator
Adult is seated
ON
OFF
Child is seated
OFF
ON
Vacant
OFF
OFF
Occupant classification system failure
OFF
ON

WIRING DIAGRAM


C128675E04


INSPECTION PROCEDURE

1.CHECK SRS WARNING LIGHT
  1. Turn the power switch ON (IG), and check the SRS warning light condition.

    OK:
    The SRS warning light does not come on.



NG
Go to step 9
OK


2.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
  1. Turn the power switch ON (IG).

  1. Check if the passenger airbag ON/OFF indicator correctly indicates the front passenger seat condition.

    OK:

    Front Passenger Seat Condition
    ON Indicator
    OFF Indicator
    Adult is seated
    ON
    OFF
    Child is seated
    OFF
    ON
    Vacant
    OFF
    OFF
    Occupant classification system failure
    OFF
    ON



OK
END
NG


3.PERFORM ZERO POINT CALIBRATION
  1. Turn the power switch OFF.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 5
OK


4.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 5
OK

END 

5.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
  1. Turn the power switch OFF.

  1. Loosen the 4 installation bolts of the front seat RH.

  1. Tighten the 4 installation bolts of the front seat RH to the specified torque (Click here).

    Torque:
    37 N*m {380 kgf*cm, 27 ft.*lbf}


NEXT


6.PERFORM ZERO POINT CALIBRATION
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 8
OK


7.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 8
OK

END 

8.CHECK CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the 4 occupant classification sensors.

    OK:
    The connectors are connected.

  1. Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.

  1. Check that the connectors are not damaged or deformed.

    OK:
    The connectors are normal.



NG
REPAIR OR REPLACE WIRE HARNESS AND CONNECTOR
OK


9.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Turn the power switch OFF.

  1. Clear the DTCs (Click here).

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC is not output.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK


10.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).


NEXT


11.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


12.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END