Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the multi-display and steering pad switch illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


E142755E02


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).

1.CHECK ILLUMINATION LIGHT
  1. Check if the illumination for the multi-display, radio receiver, steering pad switch, glove box light or others (combination meter, hazard switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.

    Result:

    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except multi-display.
    B
    Illumination comes on only for glove box light and steering pad switch.
    C



B
Go to step 6

C
GO TO METER / GAUGE SYSTEM
A


2.CHECK WIRE HARNESS (SPIRAL CABLE - BATTERY)


    E126428E01
  1. Disconnect the C12 cable connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    C12-12 (ILL+) - Body ground
    Light control switch TAIL or HEAD
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK STEERING PAD SWITCH ASSEMBLY

E126440E01

  1. Disconnect the switch connector.

  1. Connect the positive (+) lead to terminal 5 (ILL+) and the negative (-) lead to terminal 8 (EAU) of the steering pad switch connector.

  1. Check if the illumination for the steering pad switch comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY
OK


4.INSPECT SPIRAL CABLE


    I102015E08
  1. Disconnect the cable connectors.

  1. Measure the resistance of the cable.

    Standard resistance:
    Tester Connection
    Spiral Cable Position
    Specified Condition
    C12-4 (EAU) - 8 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    C12-12 (ILL+) - 5 (ILL+)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY
OK


5.CHECK WIRE HARNESS (RADIO RECEIVER - SPIRAL CABLE AND BODY GROUND)


    E126495E03
  1. Disconnect the R5 and R6 receiver connectors.

  1. Disconnect the C12 cable connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    R5-6 (GND) - C12-4 (EAU)
    Below 1 Ω
    R6-20 (GND) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER 

6.CHECK WIRE HARNESS (MULTI-DISPLAY - BATTERY AND BODY GROUND)


    B122460E23
  1. Disconnect the M13 display connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    M13-12 (ILL+) - Body ground
    Light control switch TAIL or HEAD
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK MULTI-DISPLAY


    E142507E01
  1. Reconnect the M13 display connector.

  1. Measure the voltage of the display.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    M13-11 (ILL-) - Body ground
    Light control switch TAIL or HEAD
    10 to 14 V



NG
REPLACE MULTI-DISPLAY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MULTI-DISPLAY - LIGHT CONTROL RHEOSTAT)