Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.
As a result, the radio receiver cannot be operated using the steering pad switch, and also the radio receiver itself cannot function.

WIRING DIAGRAM


E129490E02


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System.

1.CHECK STEERING PAD SWITCH CIRCUIT


    E107195E05
  1. Disconnect the R5 receiver connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    R5-7 (SW1) - R5-6 (GND)
    No switch is pushed
    Approx. 100 kΩ
    R5-7 (SW1) - R5-6 (GND)
    SEEK+ switch is pushed
    Below 2.5 Ω
    R5-7 (SW1) - R5-6 (GND)
    SEEK- switch is pushed
    Approx. 320 Ω
    R5-7 (SW1) - R5-6 (GND)
    VOL+ switch is pushed
    Approx. 1 kΩ
    R5-7 (SW1) - R5-6 (GND)
    VOL- switch is pushed
    Approx. 3.2 kΩ
    R5-8 (SW2) - R5-6 (GND)
    No switch is pushed
    Approx. 100 kΩ
    R5-8 (SW2) - R5-6 (GND)
    MODE switch is pushed
    Below 2.5 Ω
    R5-8 (SW2) - R5-6 (GND)
    VOICE switch is pushed
    3,110 Ω
    R5-8 (SW2) - R5-6 (GND)
    ON HOOK switch is pushed
    329 Ω
    R5-8 (SW2) - R5-6 (GND)
    OFF HOOK switch is pushed
    1,000 Ω



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.INSPECT STEERING PAD SWITCH

E126427E04

  1. Disconnect the steering pad switch connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    10 (AU1) - 8 (EAU)
    No switch is pushed
    Approx. 100 kΩ
    10 (AU1) - 8 (EAU)
    SEEK+ switch is pushed
    Below 2.5 Ω
    10 (AU1) - 8 (EAU)
    SEEK- switch is pushed
    Approx. 320 Ω
    10 (AU1) - 8 (EAU)
    VOL+ switch is pushed
    Approx. 1 kΩ
    10 (AU1) - 8 (EAU)
    VOL- switch is pushed
    Approx. 3.2 kΩ
    9 (AU2) - 8 (EAU)
    No switch is pushed
    Approx. 100 kΩ
    9 (AU2) - 8 (EAU)
    MODE switch is pushed
    Below 2.5 Ω
    9 (AU2) - 8 (EAU)
    VOICE switch is pushed
    3,110 Ω
    9 (AU2) - 8 (EAU)
    ON HOOK switch is pushed
    329 Ω
    9 (AU2) - 8 (EAU)
    OFF HOOK switch is pushed
    1,000 Ω



NG
REPLACE STEERING PAD SWITCH
OK


3.INSPECT SPIRAL CABLE


    I039337E21
  1. Disconnect the steering pad switch connector.

  1. Disconnect the spiral cable connector.

  1. Measure the resistance of the cable.

    Standard resistance:
    Tester connection
    Spiral Cable Position
    Specified condition
    A-8 (EAU) - C12-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    A-10 (AU1) - C12-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    A-9 (AU2) - C12-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the SRS section's precaution.



NG
REPLACE SPIRAL CABLE
OK


4.CHECK WIRE HARNESS (SPIRAL CABLE - RADIO RECEIVER)


    E127904E07
  1. Disconnect the R5 receiver connector.

  1. Disconnect the C12 cable connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    R5-7 (SW1) - C12-6 (AU1)
    Below 1 Ω
    R5-8 (SW2) - C12-5 (AU2)
    Below 1 Ω
    R5-6 (GND) - C12-4 (EAU)
    Below 1 Ω
    R5-7 (SW1) - Body ground
    10 kΩ or higher
    R5-8 (SW2) - Body ground
    10 kΩ or higher
    R5-6 (GND) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE