Home › BODY › WINDSHIELD / WINDOWGLASS › FRONT SIDE FIX WINDOW GLASS

FRONT SIDE FIX WINDOW GLASS > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL QUARTER PANEL SPACER


B073860E01
  1. Install a new spacer to the vehicle body as shown in the illustration.



2. INSTALL HOOK FASTENER


B075785E01
  1. Apply Primer G to the glass where the fastener will be installed.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

  1. Install a new hook fastener onto the glass as shown in the illustration.



3. INSTALL WINDSHIELD GLASS


    B073858E01
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply primer to the adhesive.
    3. Throw away any leftover primer.
    4. Do not apply too much primer.



  1. Using a brush or sponge, apply Primer G to the contact surface of the glass.


    B073859E04

    HINT:
    If the primer is applied to an area that is not specified, apply white gasoline to a clean cloth and wipe off the excess primer.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Apply adhesive to the glass.


    B073861E02

    Adhesive:
    Part No. 08850-00801 or equivalent


    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the glass as shown in the illustration.

      Standard measurement:
      Area
      Specified Condition
      a
      8.0 mm (0.315 in.)
      b
      6.0 mm (0.236 in.)

  1. Install the front side fix window to the vehicle body.

    1. Hold the front side fix window in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      1. Check that the spacer is attached to the vehicle body correctly.
      2. Check that the vehicle body and glass have a small gap between them.

    2. Lightly press the front surface of the glass to ensure that the glass is securely fit to the vehicle body.

      NOTICE:
      Do not drive the vehicle for the amount of time written in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



4. INSTALL FRONT PILLAR GARNISH LH


    B073594E03
  1. w/o Curtain Shield Airbag:
    Attach the 2 clips to install the pillar garnish.

  1. w/ Curtain Shield Airbag:
    Remove the protective cover.



  1. w/ Curtain Shield Airbag:
    Install the pillar garnish.



      B132621E01
    1. Set the claws of the pillar garnish to the area labeled C.

    2. Insert the tip of clip A into the pillar garnish's hole.

    3. Using needle-nose pliers, rotate the tip of clip A 90°. Then push the pillar garnish toward the vehicle body to attach the base of clip A and clip B.



5. INSTALL FRONT PILLAR GARNISH CORNER PIECE LH


    B136013E01
  1. Put protective tape as shown in the illustration.

    Standard measurement:
    Area
    Specified Condition
    A
    2.0 mm (0.079 in.)
    B
    10.0 mm (0.394 in.)
    C
    50.0 mm (1.969 in.)

  1. Attach the 5 claws to install the corner piece.



6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


7. INSTALL COWL SIDE TRIM BOARD LH


    B073588E02
  1. Attach the claw and 2 clips to install the trim board.



8. INSTALL FRONT DOOR SCUFF PLATE LH


    B073586E02
  1. Attach the 8 claws and 2 clips to install the scuff plate.



9. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.